I recently purchased Intel ATOM D945GCLF mini ITX board (excelent router in my opininon). I put another PIC 10/100 MB Level one network card. When I try to install Freebsd 6.x or 7.0 only one card-PCI card is detected, onboard not. Onboard card is 10/100 Mbits/sec LAN subsystem using the Realtek* LAN adapter device.
How to fix this problem? Huh
Any help is much apreciated.
here is dmesg:
Copyright (c) 1992-2008 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 6.3-RELEASE #0: Wed Jan 16 04:45:45 UTC 2008
root@dessler.cse.buffalo.edu:/usr/obj/usr/src/sys/SMP
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Intel(R) Atom(TM) CPU 230 @ 1.60GHz (1599.32-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x106c2 Stepping = 2
Features=0xbfe9fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE ,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,CLFLUSH,DTS,AC PI,MMX,FXSR,SSE,SSE2 ,SS,HTT,TM,PBE>
Features2=0x40e31d<SSE3,RSVD2,MON,DS_CPL,TM2,SSSE3 ,CX16,xTPR,PDCM,<b22>>
AMD Features=0x20100000<NX,LM>
AMD Features2=0x1<LAHF>
Logical CPUs per core: 2
real memory = 1063649280 (1014 MB)
avail memory = 1027358720 (979 MB)
ACPI APIC Table: <INTEL D945GLF >
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
cpu0 (BSP): APIC ID: 0
cpu1 (AP): APIC ID: 1
ioapic0: Changing APIC ID to 2
ioapic0 <Version 2.0> irqs 0-23 on motherboard
kbd1 at kbdmux0
ath_hal: 0.9.20.3 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
hptrr: HPT RocketRAID controller driver v1.1 (Jan 16 2008 04:43:12)
acpi0: <INTEL D945GLF> on motherboard
acpi0: Power Button (fixed)
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x408-0x40b on acpi0
cpu0: <ACPI CPU> on acpi0
cpu1: <ACPI CPU> on acpi0
acpi_button0: <Sleep Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
agp0: <Intel 82945G (945G GMCH) SVGA controller> port 0x30e0-0x30e7 mem 0x50300000-0x5037ffff,0x40000000-0x4fffffff,0x50380000-0x503bffff irq 16 at device 2.0 on pci0
agp0: detected 7932k stolen memory
agp0: aperture size is 256M
pcib1: <ACPI PCI-PCI bridge> at device 28.0 on pci0
pci1: <ACPI PCI bus> on pcib1
pci1: <network, ethernet> at device 0.0 (no driver attached)
pcib2: <ACPI PCI-PCI bridge> at device 28.2 on pci0
pci2: <ACPI PCI bus> on pcib2
pcib3: <ACPI PCI-PCI bridge> at device 28.3 on pci0
pci3: <ACPI PCI bus> on pcib3
uhci0: <UHCI (generic) USB controller> port 0x3080-0x309f irq 23 at device 29.0 on pci0
uhci0: [GIANT-LOCKED]
usb0: <UHCI (generic) USB controller> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1: <UHCI (generic) USB controller> port 0x3060-0x307f irq 19 at device 29.1 on pci0
uhci1: [GIANT-LOCKED]
usb1: <UHCI (generic) USB controller> on uhci1
usb1: USB revision 1.0
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2: <UHCI (generic) USB controller> port 0x3040-0x305f irq 18 at device 29.2 on pci0
uhci2: [GIANT-LOCKED]
usb2: <UHCI (generic) USB controller> on uhci2
usb2: USB revision 1.0
uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
uhci3: <UHCI (generic) USB controller> port 0x3020-0x303f irq 16 at device 29.3 on pci0
uhci3: [GIANT-LOCKED]
usb3: <UHCI (generic) USB controller> on uhci3
usb3: USB revision 1.0
uhub3: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub3: 2 ports with 2 removable, self powered
ehci0: <Intel 82801GB/R (ICH7) USB 2.0 controller> mem 0x503c0000-0x503c03ff irq 23 at device 29.7 on pci0
ehci0: [GIANT-LOCKED]
usb4: EHCI version 1.0
usb4: companion controllers, 2 ports each: usb0 usb1 usb2 usb3
usb4: <Intel 82801GB/R (ICH7) USB 2.0 controller> on ehci0
usb4: USB revision 2.0
uhub4: Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub4: 8 ports with 8 removable, self powered
pcib4: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pci4: <ACPI PCI bus> on pcib4
rl0: <RealTek 8139 10/100BaseTX> port 0x1000-0x10ff mem 0x50100000-0x501000ff irq 21 at device 0.0 on pci4
miibus0: <MII bus> on rl0
rlphy0: <RealTek internal media interface> on miibus0
rlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
rl0: Ethernet address: 00:11:6b:95:f9:d7
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH7 UDMA100 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0x30b0-0x30bf irq 18 at device 31.1 on pci0
ata0: <ATA channel 0> on atapci0
ata1: <ATA channel 1> on atapci0
atapci1: <Intel ICH7 SATA300 controller> port 0x30c8-0x30cf,0x30ec-0x30ef,0x30c0-0x30c7,0x30e8-0x30eb,0x30a0-0x30af irq 19 at device 31.2 on pci0
ata2: <ATA channel 0> on atapci1
ata3: <ATA channel 1> on atapci1
pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: [GIANT-LOCKED]
psm0: model IntelliMouse, device ID 3
pmtimer0 on isa0
ppc0: parallel port not found.
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0: configured irq 4 not in bitmap of probed irqs 0
sio0: port may not be enabled
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 8250 or not responding
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
umass0: Generic USB Flash Disk, rev 1.10/1.00, addr 2
Timecounters tick every 1.000 msec
hptrr: no controller detected.
ad0: FAILURE - SET_MULTI status=51<READY,DSC,ERROR> error=4<ABORTED>
ad0: 499MB <InnoDisk Corp. - EDC4000 512MB 06/05/18> at ata0-master UDMA66
da0 at umass-sim0 bus 0 target 0 lun 0
da0: <Generic USB Flash Disk 2.01> Removable Direct Access SCSI-2 device
da0: 1.000MB/s transfers
da0: 127MB (260288 512 byte sectors: 64H 32S/T 127C)
acd0: DVDROM <TSSTcorpDVD-ROM SH-D163B/SB01> at ata3-master SATA150
SMP: AP CPU #1 Launched!
Trying to mount root from ufs:/dev/ad0s1a
and pciconf -lv
hostb0@pci0:0:0: class=0x060000 card=0x464c8086 chip=0x27708086 rev=0x02 hdr=0x00
vendor = 'Intel Corporation'
device = '82945G/GZ/P/PL Host Bridge/DRAM Controller'
class = bridge
subclass = HOST-PCI
agp0@pci0:2:0: class=0x030000 card=0x464c8086 chip=0x27728086 rev=0x02 hdr=0x00
vendor = 'Intel Corporation'
device = '82945G Integrated Graphics Controller'
class = display
subclass = VGA
pcib1@pci0:28:0: class=0x060400 card=0x00000000 chip=0x27d08086 rev=0x01 hdr=0x01
vendor = 'Intel Corporation'
device = '82801G (ICH7 Family) PCIe Root Port'
class = bridge
subclass = PCI-PCI
pcib2@pci0:28:2: class=0x060400 card=0x00000000 chip=0x27d48086 rev=0x01 hdr=0x01
vendor = 'Intel Corporation'
device = '82801G (ICH7 Family) PCIe Root Port'
class = bridge
subclass = PCI-PCI
pcib3@pci0:28:3: class=0x060400 card=0x00000000 chip=0x27d68086 rev=0x01 hdr=0x01
vendor = 'Intel Corporation'
device = '82801G (ICH7 Family) PCIe Root Port'
class = bridge
subclass = PCI-PCI
uhci0@pci0:29:0: class=0x0c0300 card=0x464c8086 chip=0x27c88086 rev=0x01 hdr=0x00
vendor = 'Intel Corporation'
device = '82801G (ICH7 Family) USB Universal Host Controller'
class = serial bus
subclass = USB
uhci1@pci0:29:1: class=0x0c0300 card=0x464c8086 chip=0x27c98086 rev=0x01 hdr=0x00
vendor = 'Intel Corporation'
device = '82801G (ICH7 Family) USB Universal Host Controller'
class = serial bus
subclass = USB
uhci2@pci0:29:2: class=0x0c0300 card=0x464c8086 chip=0x27ca8086 rev=0x01 hdr=0x00
vendor = 'Intel Corporation'
device = '82801G (ICH7 Family) USB Universal Host Controller'
class = serial bus
subclass = USB
uhci3@pci0:29:3: class=0x0c0300 card=0x464c8086 chip=0x27cb8086 rev=0x01 hdr=0x00
vendor = 'Intel Corporation'
device = '82801G (ICH7 Family) USB Universal Host Controller'
class = serial bus
subclass = USB
ehci0@pci0:29:7: class=0x0c0320 card=0x464c8086 chip=0x27cc8086 rev=0x01 hdr=0x00
vendor = 'Intel Corporation'
device = '82801G (ICH7 Family) USB 2.0 Enhanced Host Controller'
class = serial bus
subclass = USB
pcib4@pci0:30:0: class=0x060401 card=0x464c8086 chip=0x244e8086 rev=0xe1 hdr=0x01
vendor = 'Intel Corporation'
device = '82801 Family (ICH2/3/4/4/5/5/6/7/8/9,63xxESB) Hub Interface to PCI Bridge'
class = bridge
subclass = PCI-PCI
isab0@pci0:31:0: class=0x060100 card=0x464c8086 chip=0x27b88086 rev=0x01 hdr=0x00
vendor = 'Intel Corporation'
device = '945GL Intel 82801GB/GR (ICH7 Family) LPC Interface Controller - 27B8'
class = bridge
subclass = PCI-ISA
atapci0@pci0:31:1: class=0x01018a card=0x464c8086 chip=0x27df8086 rev=0x01 hdr=0x00
vendor = 'Intel Corporation'
device = '82801G (ICH7 Family) Ultra ATA Storage Controller'
class = mass storage
subclass = ATA
atapci1@pci0:31:2: class=0x01018f card=0x464c8086 chip=0x27c08086 rev=0x01 hdr=0x00
vendor = 'Intel Corporation'
device = '82801GB/GR/GH (ICH7 Family) Serial ATA Storage Controller'
class = mass storage
subclass = ATA
none0@pci0:31:3: class=0x0c0500 card=0x464c8086 chip=0x27da8086 rev=0x01 hdr=0x00
vendor = 'Intel Corporation'
device = '82801G (ICH7 Family) SMBus Controller'
class = serial bus
subclass = SMBus
none1@pci1:0:0: class=0x020000 card=0x00018086 chip=0x813610ec rev=0x02 hdr=0x00
vendor = 'Realtek Semiconductor'
device = 'RTL8139/810x Family Fast Ethernet NIC'
class = network
subclass = ethernet
rl0@pci4:0:0: class=0x020000 card=0x813910ec chip=0x813910ec rev=0x10 hdr=0x00
vendor = 'Realtek Semiconductor'
device = 'RT8139 (A/B/C/810x/813x/C+) Fast Ethernet Adapter'
class = network
subclass = ethernet
any help is really apreciated
onboard card works in Puppy linux ...????
Regards
Regards