View Single Post
  #7   (View Single Post)  
Old 2nd January 2009
bogd bogd is offline
New User
 
Join Date: Dec 2008
Posts: 7
Default

Hi jggimi

Here is the result from running smartctl -a /dev/wd0c

Code:
smartctl version 5.38 [x86_64-unknown-openbsd4.4] Copyright (C) 2002-8 Bruce All
en
Home page is http://smartmontools.sourceforge.net/

=== START OF INFORMATION SECTION ===
Device Model:     FUJITSU MHY2250BH
Serial Number:    K413T842NJ4R
Firmware Version: 890B
User Capacity:    250,059,350,016 bytes
Device is:        Not in smartctl database [for details use: -P showall]
ATA Version is:   8
ATA Standard is:  ATA-8-ACS revision 3f
Local Time is:    Fri Jan  2 16:56:41 2009 EST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x00) Offline data collection activity
                                        was never started.
                                        Auto Offline Data Collection: Disabled.
Self-test execution status:      (   0) The previous self-test routine completed
                                        without error or no self-test has ever 
                                        been run.
Total time to complete Offline 
data collection:                 (1009) seconds.
Offline data collection
capabilities:                    (0x51) SMART execute Offline immediate.
                                        No Auto Offline data collection support.
                                        Suspend Offline collection upon new
                                        command.
                                        No Offline surface scan supported.
                                        Self-test supported.
                                        No Conveyance Self-test supported.
                                        Selective Self-test supported.
SMART capabilities:            (0x0003) Saves SMART data before entering
                                        power-saving mode.
                                        Supports SMART auto save timer.
Error logging capability:        (0x01) Error logging supported.
                                        General Purpose Logging supported.
Short self-test routine 
recommended polling time:        (   2) minutes.
Extended self-test routine
recommended polling time:        ( 143) minutes.
SCT capabilities:              (0x003f) SCT Status supported.
                                        SCT Feature Control supported.
                                        SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_
FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x000f   100   100   046    Pre-fail  Always       -
       60550
  2 Throughput_Performance  0x0005   100   100   030    Pre-fail  Offline      -
       53411840
  3 Spin_Up_Time            0x0003   100   100   025    Pre-fail  Always       -
       1
  4 Start_Stop_Count        0x0032   099   099   000    Old_age   Always       -
       394
  5 Reallocated_Sector_Ct   0x0033   100   100   024    Pre-fail  Always       -
       8589934592000
  7 Seek_Error_Rate         0x000f   100   100   047    Pre-fail  Always       -
       1538
  8 Seek_Time_Performance   0x0005   100   100   019    Pre-fail  Offline      -
       0
  9 Power_On_Hours          0x0032   097   097   000    Old_age   Always       -
       1871
 10 Spin_Retry_Count        0x0013   100   100   020    Pre-fail  Always       -
       0
 11 Calibration_Retry_Count 0x0032   253   253   000    Old_age   Always       -
       0
 12 Power_Cycle_Count       0x0032   100   100   000    Old_age   Always       -
       378
182 Unknown_Attribute       0x0032   100   100   000    Old_age   Always       -
       0
184 Unknown_Attribute       0x0033   253   253   097    Pre-fail  Always       -
       0
185 Unknown_Attribute       0x0010   253   253   000    Old_age   Offline      -
       0
186 Unknown_Attribute       0x0032   253   253   000    Old_age   Always       -
       0
187 Reported_Uncorrect      0x0032   100   100   000    Old_age   Always       -
       42949672960
188 Unknown_Attribute       0x0032   100   100   000    Old_age   Always       -
       0
189 High_Fly_Writes         0x003a   100   100   000    Old_age   Always       -
       0
190 Airflow_Temperature_Cel 0x0022   057   045   000    Old_age   Always       -
       43 (Lifetime Min/Max 20/45)
191 G-Sense_Error_Rate      0x0032   253   253   000    Old_age   Always       -
       16580608
192 Power-Off_Retract_Count 0x0032   100   100   000    Old_age   Always       -
       2031647
193 Load_Cycle_Count        0x0032   099   099   000    Old_age   Always       -
       35569
195 Hardware_ECC_Recovered  0x001a   100   100   000    Old_age   Always       -
       16
196 Reallocated_Event_Count 0x0032   100   100   000    Old_age   Always       -
       445448192
197 Current_Pending_Sector  0x0012   100   100   000    Old_age   Always       -
       0
198 Offline_Uncorrectable   0x0010   100   100   000    Old_age   Offline      -
       0
199 UDMA_CRC_Error_Count    0x003e   200   253   000    Old_age   Always       -
       0
200 Multi_Zone_Error_Rate   0x000f   100   100   060    Pre-fail  Always       -
       6691
203 Run_Out_Cancel          0x0002   100   100   000    Old_age   Always       -
       3732259668357
240 Head_Flying_Hours       0x003e   200   200   000    Old_age   Always       -
       0

SMART Error Log Version: 1
No Errors Logged

SMART Self-test log structure revision number 1
No self-tests have been logged.  [To run self-tests, use: smartctl -t]


SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Reply With Quote