[deathbyfreezeray]

I managed to install NetBSD 6.1.5 on my G4 mac mini but the keyboard doesn't work. I have to ssh in to use the machine. Things to note are that it worked in the INSTALL CD, wscons=YES in my rc.conf, and the the kernel appears to detect it as shown by the output of dmesg below:

EDIT: I should add in the log it is listed as "uhub4 at uhub3 port 1: Apple, Inc. Keyboard Hub, class 9/0, rev 2.00/96.15, addr 2" but doesn't appear to be shown as a keyboard.

ersave: 1
cpu0: 1250.00 MHz, 512KB L2 cache no parity parity enabled
memory0 at mainbus0: len=128
spdmem0 at memory0
spdmem0: DDR SDRAM, no parity or ECC, 1GB, 333MHz (PC-2700)
spdmem0: 13 rows, 11 cols, 2 ranks, 4 banks/chip, 6.0ns cycle time
spdmem0: tAA-tRCD-tRP-tRAS: 1-3-3-7
spdmem0: voltage SSTL 2.5V, refresh time 7.8us (self-refreshing)
uni_n0 at mainbus0 address 0xf8000000
hw-clock at uni_n0 not configured
ki2c0 at uni_n0 address 0xf8001000
iic1 at ki2c0: I2C bus
cereal at ki2c0 address 0x1c0 not configured
uninorth0 at mainbus0
pci0 at uninorth0 bus 0
pci0: i/o space, memory space enabled
pchb0 at pci0 dev 11 function 0
pchb0: Apple Computer UniNorth AGP Bridge (rev. 0x00)
genfb0 at pci0 dev 16 function 0: ATI Technologies Radeon 9200 5962 (rev. 0x01)
genfb0: framebuffer at 0x9c008000, size 1280x768, depth 32, stride 5120
wsdisplay0 at genfb0 kbdmux 1: console (default, vt100 emulation)
wsmux1: connecting to wsdisplay0
drm at genfb0 not configured
uninorth1 at mainbus0
pci1 at uninorth1 bus 0
pci1: i/o space, memory space enabled
pchb1 at pci1 dev 11 function 0
pchb1: Apple Computer UniNorth Host-PCI Bridge (rev. 0x00)
obio0 at pci1 dev 23 function 0: addr 0x80000000
zsc0 at obio0 irq 22,23
zstty0 at zsc0 channel 0
zstty1 at zsc0 channel 1
snapper0 at obio0 offset 0x10000: irq 30,1,2
pmu0 at obio0 offset 0x16000 irq 47:  rev. 85
pmu0: initializing IIC bus
pmu0: initializing RTC
pmu0: power-mgt not configured
pmu0: pmu-pwm-fans not configured
ki2c1 at obio0
iic2 at ki2c1: I2C bus
cereal at ki2c1 address 0x1c0 not configured
wdc0 at obio0 offset 0x20000 irq 24, level triggered: DMA transfer
atabus0 at wdc0 channel 0
snapper0: software codec
audio0 at snapper0: full duplex, playback, capture
ohci0 at pci1 dev 24 function 0: Apple Computer Intrepid USB Controller (rev. 0x00)
ohci0: memory access is disabled
ohci1 at pci1 dev 25 function 0: Apple Computer Intrepid USB Controller (rev. 0x00)
ohci1: memory access is disabled
ohci2 at pci1 dev 26 function 0: Apple Computer Intrepid USB Controller (rev. 0x00)
ohci2: interrupting at irq 29
ohci2: OHCI version 1.0, legacy support
usb0 at ohci2: USB revision 1.0
ohci3 at pci1 dev 27 function 0: NEC USB Host Controller (rev. 0x43)
ohci3: interrupting at irq 63
ohci3: OHCI version 1.0
usb1 at ohci3: USB revision 1.0
ohci4 at pci1 dev 27 function 1: NEC USB Host Controller (rev. 0x43)
ohci4: interrupting at irq 63
ohci4: OHCI version 1.0
usb2 at ohci4: USB revision 1.0
ehci0 at pci1 dev 27 function 2: NEC USB2 Host Controller (rev. 0x04)
ehci0: interrupting at irq 63
ehci0: EHCI version 1.0
ehci0: companion controllers, 3 ports each: ohci3 ohci4
usb3 at ehci0: USB revision 2.0
uninorth2 at mainbus0
pci2 at uninorth2 bus 0
pci2: i/o space, memory space enabled
pchb2 at pci2 dev 11 function 0
pchb2: Apple Computer UniNorth Host-PCI Bridge (rev. 0x00)
wdc1 at pci2 dev 13 function 0: interrupting at irq 39
atabus1 at wdc1 channel 0
fwohci0 at pci2 dev 14 function 0: Apple Computer UniNorth Firewire (rev. 0x81)
fwohci0: interrupting at irq 40
fwohci0: OHCI version 1.10 (ROM=0)
fwohci0: No. of Isochronous channels is 8.
fwohci0: EUI64 00:11:24:ff:fe:7e:86:f6
fwohci0: Phy 1394a available S400, 2 ports.
fwohci0: Link S400, max_rec 2048 bytes.
ieee1394if0 at fwohci0: IEEE1394 bus
fwip0 at ieee1394if0: IP over IEEE1394
fwohci0: Initiate bus reset
gem0 at pci2 dev 15 function 0: Apple Computer GMAC Ethernet (rev. 0x80)
gem0: interrupting at irq 41
bmtphy0 at gem0 phy 0: BCM5221 10/100 media interface, rev. 4
bmtphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
gem0: Ethernet address 00:11:24:7e:86:f6, 10KB RX fifo, 4KB TX fifo
vmmask 66f80000 schedmask 7ff80000 highmask 7ff80000
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
timecounter: Timecounter "mftb" frequency 41620997 Hz quality 100
fwohci0: BUS reset
fwohci0: node_id=0xc800ffc0, gen=2, CYCLEMASTER mode
ieee1394if0: 1 nodes, maxhop <= 0 cable IRM irm(0) (me)
ieee1394if0: bus manager 0
uhub0 at usb0: Apple Computer OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhub1 at usb1: NEC OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 3 ports with 3 removable, self powered
uhub2 at usb2: NEC OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
uhub3 at usb3: NEC EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub3: 5 ports with 5 removable, self powered
atapibus0 at atabus1: 2 targets
cd0 at atapibus0 drive 1: <MATSHITACD-RW  CW-8124, , DACD> cdrom removable
cd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 2 (Ultra/33)
wd0 at atabus1 drive 0
wd0: <ST940110A>
wd0: drive supports 16-sector PIO transfers, LBA48 addressing
wd0: 38154 MB, 77520 cyl, 16 head, 63 sec, 512 bytes/sect x 78140160 sectors
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
wd0(wdc1:0:0): using PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100) (using DMA)
cd0(wdc1:0:1): using PIO mode 4, DMA mode 2, Ultra-DMA mode 2 (Ultra/33) (using DMA)
uhub4 at uhub3 port 1: Apple, Inc. Keyboard Hub, class 9/0, rev 2.00/96.15, addr 2
uhub4: single transaction translator
uhub4: 3 ports with 2 removable, bus powered
uhub4: device problem, disabling port 2
Kernelized RAIDframe activated
swwdog0: software watchdog initialized
boot device: wd0
root on wd0a dumps on wd0b
root file system type: ffs
uhidev0 at uhub2 port 1 configuration 1 interface 0
uhidev0: Holtek Semiconductor product 0x1135, rev 1.10/1.00, addr 2, iclass 3/1
ums0 at uhidev0: 5 buttons and Z dir
wsmouse0 at ums0 mux 0
wsdisplay0: screen 1 added (default, vt100 emulation
wsdisplay0: screen 2 added (default, vt100 emulation)
wsdisplay0: screen 3 added (default, vt100 emulation)
wsdisplay0: screen 4 added (default, vt100 emulation)