Code:
# ifconfig -A
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 33200
priority: 0
groups: lo
inet 127.0.0.1 netmask 0xff000000
inet6 ::1 prefixlen 128
inet6 fe80::1%lo0 prefixlen 64 scopeid 0x5
ral0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
lladdr 00:1d:6a:3a:48:66
priority: 4
groups: wlan
media: IEEE802.11 autoselect mode 11g hostap
status: active
ieee80211: nwid Inland_Empire chan 10 bssid 00:1d:6a:3a:48:66
inet 192.168.1.1 netmask 0xffffff00 broadcast 192.168.1.255
inet6 fe80::21d:6aff:fe3a:4866%ral0 prefixlen 64 scopeid 0x1
re0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
lladdr 00:18:e7:18:3d:34
priority: 0
media: Ethernet autoselect (100baseTX full-duplex,rxpause,txpause)
status: active
inet 192.168.0.1 netmask 0xffffff00 broadcast 192.168.0.255
inet6 fe80::218:e7ff:fe18:3d34%re0 prefixlen 64 scopeid 0x2
em0: flags=8b43<UP,BROADCAST,RUNNING,PROMISC,ALLMULTI,SIMPLEX,MULTICAST> mtu 1500
lladdr 00:0d:60:47:d3:9c
priority: 0
groups: egress
media: Ethernet autoselect (100baseTX full-duplex,rxpause,txpause)
status: active
inet6 fe80::20d:60ff:fe47:d39c%em0 prefixlen 64 scopeid 0x3
inet 70.64.72.16 netmask 0xfffffc00 broadcast 255.255.255.255
enc0: flags=0<> mtu 1536
priority: 0
pflog0: flags=141<UP,RUNNING,PROMISC> mtu 33200
priority: 0
groups: pflog
Code:
# netstat -rn -f inet
Routing tables
Internet:
Destination Gateway Flags Refs Use Mtu Prio Iface
default 70.64.72.1 UGS 0 173 - 8 em0
70.64.72/22 link#3 UC 1 0 - 4 em0
70.64.72.1 00:30:b8:c5:05:40 UHLc 1 0 - 4 em0
70.64.72.16 127.0.0.1 UGHS 0 0 33200 8 lo0
127/8 127.0.0.1 UGRS 0 0 33200 8 lo0
127.0.0.1 127.0.0.1 UH 2 0 33200 4 lo0
192.168.0/24 link#2 UC 1 0 - 4 re0
192.168.0.10 00:24:8c:b9:1d:e4 UHLc 1 269 - 4 re0
192.168.1/24 link#1 UC 0 0 - 4 ral0
224/4 127.0.0.1 URS 0 0 33200 8 lo0
I have 2 laptops connecting to ral0 i'm also not using dhcpd