Thread: soekris help
View Single Post
  #1   (View Single Post)  
Old 13th December 2008
revzalot's Avatar
revzalot revzalot is offline
Shell Scout
 
Join Date: May 2008
Posts: 123
Default soekris help

Awhile back I bought a soekris off ebay and installed OBSD in a compact flash using bowlfish. I'm getting a ddb error unknown to me. I really hope it's not the box and just the CF.

Code:
comBIOS ver. 1.27  20041122  Copyright (C) 2000-2004 Soekris Engineering.

net45xx

0064 Mbyte Memory                        CPU 80486 133 Mhz 

Pri Mas  LEXAR ATA FLASH                 LBA 993-16-63  500 Mbyte

Slot   Vend Dev  ClassRev Cmd  Stat CL LT HT  Base1    Base2   Int 
-------------------------------------------------------------------
0:00:0 1022 3000 06000000 0006 2280 00 00 00 00000000 00000000 
0:17:0 104C AC51 06070000 0107 0210 10 3F 82 A0000000 020000A0 10
0:17:1 104C AC51 06070000 0107 0210 10 3F 82 A0001000 020000A0 10
0:18:0 100B 0020 02000000 0107 0290 00 3F 00 0000E101 A0002000 11
0:19:0 100B 0020 02000000 0107 0290 00 3F 00 0000E201 A0003000 05

 1 Seconds to automatic boot.   Press Ctrl-P for entering Monitor.
Using drive 0, partition 3.
Loading...
probing: pc0 com0 com1 mem[639K 63M a20=on] 
disk: hd0+
>> OpenBSD/i386 BOOT 3.01
switching console to com0                                                       
>> OpenBSD/i386 BOOT 3.01                                                       
com0: changing speed to 19200 baud in 5 seconds, change your terminal to match! 
                                                                                
com0: 19200 baud                                                                
boot>                                                                           
booting hd0a:/bsd: 1833484+365768 [52+105808+97045]=0x24a8e4                    
entry point at 0x200120                                                         
                                                                                
[ using 203280 bytes of bsd ELF symbol table ]                                  
Copyright (c) 1982, 1986, 1989, 1991, 1993                                      
        The Regents of the University of California.  All rights reserved.      
Copyright (c) 1995-2008 OpenBSD. All rights reserved.  http://www.OpenBSD.org   
                                                                                
OpenBSD 4.3 (NET45xx) #0: Fri Mar 21 12:39:33 PDT 2008                          
    anton@hpv.my.domain:/usr/src/sys/arch/i386/compile/NET45xx                  
cpu0: AMD Am486DX4 W/B or Am5x86 W/B 150 ("AuthenticAMD" 486-class)             
cpu0: FPU                                                                       
real mem  = 66678784 (63MB)                                                     
avail mem = 60432384 (57MB)                                                     
mainbus0 at root                                                                
bios0 at mainbus0: AT/286+ BIOS, date 20/41/22, BIOS32 rev. 0 @ 0xf7840         
pcibios0 at bios0: rev 2.0 @ 0xf0000/0x10000                                    
pcibios0: pcibios_get_intr_routing - function not supported                     
pcibios0: PCI IRQ Routing information unavailable.                              
pcibios0: PCI bus #2 is the last bus                                            
bios0: ROM list: 0xc8000/0x9000                                                 
cpu0 at mainbus0                                                                
pci0 at mainbus0 bus 0: configuration mode 1 (no bios)                          
elansc0 at pci0 dev 0 function 0 "AMD ElanSC520 PCI" rev 0x00: product 0 steppi>
gpio0 at elansc0: 32 pins                                                       
cbb0 at pci0 dev 17 function 0 "TI PCI1420 CardBus" rev 0x00: irq 10            
cbb1 at pci0 dev 17 function 1 "TI PCI1420 CardBus" rev 0x00: irq 10            
sis0 at pci0 dev 18 function 0 "NS DP83815 10/100" rev 0x00, DP83816A: irq 11, 8
nsphyter0 at sis0 phy 0: DP83815 10/100 PHY, rev. 1                             
sis1 at pci0 dev 19 function 0 "NS DP83815 10/100" rev 0x00, DP83816A: irq 5, a9
nsphyter1 at sis1 phy 0: DP83815 10/100 PHY, rev. 1                             
cardslot0 at cbb0 slot 0 flags 0                                                
cardbus0 at cardslot0: bus 1 device 0 cacheline 0x10, lattimer 0x3f             
pcmcia0 at cardslot0                                                            
cardslot1 at cbb1 slot 1 flags 0                                                
cardbus1 at cardslot1: bus 2 device 0 cacheline 0x10, lattimer 0x3f             
pcmcia1 at cardslot1                                                            
isa0 at mainbus0                                                                
isadma0 at isa0                                                                 
wdc0 at isa0 port 0x1f0/8 irq 14                                                
wd0 at wdc0 channel 0 drive 0: <LEXAR ATA FLASH>                                
wd0: 16-sector PIO, LBA, 488MB, 1000944 sectors                                 
wd0(wdc0:0:0): using BIOS timings                                               
npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16                
pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo                       
pccom0: console                                                                 
pccom1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo                       
biomask f7c7 netmask ffe7 ttymask ffe7                                          
root on wd0a swap on wd0b dump on wd0b                                          
filesystem type 8 not known.. assuming ffs                                      
warning: /dev/console error 22                                                  
exec /sbin/init: error 22                                                       
exec /sbin/oinit: error 22                                                      
exec /sbin/init.bak: error 22                                                   
init: not found                                                                 
panic: no init                                                                  
Stopped at      Debugger+0x4:   leave                                           
RUN AT LEAST 'trace' AND 'ps' AND INCLUDE OUTPUT WHEN REPORTING THIS PANIC!     
DO NOT EVEN BOTHER REPORTING THIS WITHOUT INCLUDING THAT INFORMATION!           
ddb>
Reply With Quote