View Single Post
  #6   (View Single Post)  
Old 19th August 2008
TomAmundsen TomAmundsen is offline
Real Name: Tom Amundsen
Computional Linguist
 
Join Date: Jul 2008
Location: Los Angeles, CA
Posts: 23
Default

Quote:
Originally Posted by BSDfan666 View Post
You need to associate with an access point before you can use a Wireless interface.. otherwise how would you differentiate between your network and a neighbours?

As mentioned, bfe(4) is not a wireless interface.. with that said, it's probably an unused Ethernet port.

Post the output of ifconfig so we can determine more about your current configuration... a dmesg would be nice too.

Please contain the output inside [code][/code] blocks..


Yeah, that's not a viable way of support... unfortunately.
Here is the result of
>ifconfig
Code:
bfe0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
	options=8<VLAN_MTU>
	ether 00:0b:db:9c:d5:c4
	inet6 fe80::20b:dbff:fe9c:d5c4%bfe0 prefixlen 64 scopeid 0x1 
	inet 192.168.1.100 netmask 0xffffff00 broadcast 192.168.1.255
	media: Ethernet autoselect (none)
	status: no carrier
fwe0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500
	options=8<VLAN_MTU>
	ether 02:c0:4f:67:94:61
	ch 1 dma -1
fwip0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500
	lladdr 0.c0.4f.4a.20.67.94.61.a.2.ff.fe.0.0.0.0
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> metric 0 mtu 16384
	inet6 ::1 prefixlen 128 
	inet6 fe80::1%lo0 prefixlen 64 scopeid 0x4 
	inet 127.0.0.1 netmask 0xff000000
and now
> dmesg
Code:
Copyright (c) 1992-2008 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
	The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 7.0-RELEASE #0: Sun Feb 24 19:59:52 UTC 2008
    root@logan.cse.buffalo.edu:/usr/obj/usr/src/sys/GENERIC
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Genuine Intel(R) CPU 3.06GHz (1594.70-MHz 686-class CPU)
  Origin = "GenuineIntel"  Id = 0xf29  Stepping = 9
  Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
  Features2=0x4400<CNXT-ID,xTPR>
real memory  = 535691264 (510 MB)
avail memory = 510291968 (486 MB)
ACPI APIC Table: <INTEL  MONTARA >
ioapic0 <Version 2.0> irqs 0-23 on motherboard
kbd1 at kbdmux0
ath_hal: 0.9.20.3 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
hptrr: HPT RocketRAID controller driver v1.1 (Feb 24 2008 19:59:27)
acpi0: <DELL MwoodNwd> on motherboard
acpi0: [ITHREAD]
acpi0: Power Button (fixed)
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x1008-0x100b on acpi0
acpi_ec0: <Embedded Controller: GPE 0x1c> port 0x62,0x66 on acpi0
cpu0: <ACPI CPU> on acpi0
device_attach: acpi_perf0 attach returned 6
p4tcc0: <CPU Frequency Thermal Control> on cpu0
device_attach: acpi_perf0 attach returned 6
acpi_button0: <Power Button> on acpi0
acpi_button1: <Sleep Button> on acpi0
acpi_lid0: <Control Method Lid Switch> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
agp0: <Intel 82855GM host to AGP bridge> on hostb0
pci0: <base peripheral> at device 0.1 (no driver attached)
pci0: <base peripheral> at device 0.3 (no driver attached)
pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0
pci1: <ACPI PCI bus> on pcib1
vgapci0: <VGA-compatible display> port 0x3000-0x30ff mem 0xd8000000-0xdfffffff,0xd0100000-0xd010ffff irq 20 at device 0.0 on pci1
uhci0: <Intel 82801DB (ICH4) USB controller USB-A> port 0x1800-0x181f irq 16 at device 29.0 on pci0
uhci0: [GIANT-LOCKED]
uhci0: [ITHREAD]
usb0: <Intel 82801DB (ICH4) USB controller USB-A> on uhci0
usb0: USB revision 1.0
uhub0: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb0
uhub0: 2 ports with 2 removable, self powered
uhci1: <Intel 82801DB (ICH4) USB controller USB-B> port 0x1820-0x183f irq 19 at device 29.1 on pci0
uhci1: [GIANT-LOCKED]
uhci1: [ITHREAD]
usb1: <Intel 82801DB (ICH4) USB controller USB-B> on uhci1
usb1: USB revision 1.0
uhub1: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb1
uhub1: 2 ports with 2 removable, self powered
uhci2: <Intel 82801DB (ICH4) USB controller USB-C> port 0x1840-0x185f irq 18 at device 29.2 on pci0
uhci2: [GIANT-LOCKED]
uhci2: [ITHREAD]
usb2: <Intel 82801DB (ICH4) USB controller USB-C> on uhci2
usb2: USB revision 1.0
uhub2: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb2
uhub2: 2 ports with 2 removable, self powered
ehci0: <Intel 82801DB/L/M (ICH4) USB 2.0 controller> mem 0xd0000000-0xd00003ff irq 23 at device 29.7 on pci0
ehci0: [GIANT-LOCKED]
ehci0: [ITHREAD]
usb3: EHCI version 1.0
usb3: companion controllers, 2 ports each: usb0 usb1 usb2
usb3: <Intel 82801DB/L/M (ICH4) USB 2.0 controller> on ehci0
usb3: USB revision 2.0
uhub3: <Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1> on usb3
uhub3: 6 ports with 6 removable, self powered
pcib2: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pci2: <ACPI PCI bus> on pcib2
bfe0: <Broadcom BCM4401 Fast Ethernet> mem 0xd0204000-0xd0205fff irq 17 at device 1.0 on pci2
miibus0: <MII bus> on bfe0
bmtphy0: <BCM4401 10/100baseTX PHY> PHY 1 on miibus0
bmtphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
bfe0: using obsoleted if_watchdog interface
bfe0: Ethernet address: 00:0b:db:9c:d5:c4
bfe0: [ITHREAD]
pci2: <network> at device 2.0 (no driver attached)
cbb0: <TI4510 PCI-CardBus Bridge> irq 16 at device 4.0 on pci2
cardbus0: <CardBus bus> on cbb0
pccard0: <16-bit PCCard bus> on cbb0
cbb0: [ITHREAD]
fwohci0: <1394 Open Host Controller Interface> mem 0xd0208000-0xd02087ff,0xd0200000-0xd0203fff irq 16 at device 4.1 on pci2
fwohci0: [FILTER]
fwohci0: OHCI version 1.10 (ROM=0)
fwohci0: No. of Isochronous channels is 4.
fwohci0: EUI64 00:c0:4f:4a:20:67:94:61
fwohci0: Phy 1394a available S400, 2 ports.
fwohci0: Link S400, max_rec 2048 bytes.
firewire0: <IEEE1394(FireWire) bus> on fwohci0
dcons_crom0: <dcons configuration ROM> on firewire0
dcons_crom0: bus_addr 0x1f46c000
fwe0: <Ethernet over FireWire> on firewire0
if_fwe0: Fake Ethernet address: 02:c0:4f:67:94:61
fwe0: Ethernet address: 02:c0:4f:67:94:61
fwip0: <IP over FireWire> on firewire0
fwip0: Firewire address: 00:c0:4f:4a:20:67:94:61 @ 0xfffe00000000, S400, maxrec 2048
sbp0: <SBP-2/SCSI over FireWire> on firewire0
fwohci0: Initiate bus reset
fwohci0: BUS reset
fwohci0: node_id=0xc000ffc0, gen=1, CYCLEMASTER mode
ichss: enabling SpeedStep support
ichss: enabling SpeedStep support
ichss0: <SpeedStep ICH> on cpu0
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH4 UDMA100 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0x1860-0x186f at device 31.1 on pci0
ata0: <ATA channel 0> on atapci0
ata0: [ITHREAD]
ata1: <ATA channel 1> on atapci0
ata1: [ITHREAD]
pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
pci0: <multimedia, audio> at device 31.5 (no driver attached)
pci0: <simple comms, generic modem> at device 31.6 (no driver attached)
acpi_tz0: <Thermal Zone> on acpi0
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
atkbd0: [ITHREAD]
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: [GIANT-LOCKED]
psm0: [ITHREAD]
psm0: model Generic PS/2 mouse, device ID 0
acpi_acad0: <AC Adapter> on acpi0
battery0: <ACPI Control Method Battery> on acpi0
pmtimer0 on isa0
orm0: <ISA Option ROMs> at iomem 0xc0000-0xcffff,0xd0000-0xd0fff,0xd1000-0xd27ff,0xdc000-0xdffff,0xe0000-0xe3fff pnpid ORM0000 on isa0
ppc0: parallel port not found.
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0: configured irq 4 not in bitmap of probed irqs 0
sio0: port may not be enabled
sio0: configured irq 4 not in bitmap of probed irqs 0
sio0: port may not be enabled
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 8250 or not responding
sio0: [FILTER]
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
Timecounter "TSC" frequency 1594699404 Hz quality 800
Timecounters tick every 1.000 msec
hptrr: no controller detected.
firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
firewire0: bus manager 0 (me)
acd0: CDRW <Samsung CD-RW/DVD-ROM SN-324B/U102> at ata0-master UDMA33
ad2: 38154MB <IC25N040ATCS04 0 CA4OA72A> at ata1-master UDMA100
acd0: FAILURE - READ_BIG ILLEGAL REQUEST asc=0x64 ascq=0x00 
GEOM_LABEL: Label for provider acd0 is iso9660/FreeBSD_Packages_2.
acd0: FAILURE - READ_BIG ILLEGAL REQUEST asc=0x64 ascq=0x00 
Trying to mount root from ufs:/dev/ad2s1a
logo_saver: the console does not support M_VGA_CG320
module_register_init: MOD_LOAD (logo_saver, 0xc32d47b0, 0) error 19
umass0: <SanDisk U3 Cruzer Micro, class 0/0, rev 2.00/0.10, addr 2> on uhub3
da0 at umass-sim0 bus 0 target 0 lun 0
da0: <SanDisk U3 Cruzer Micro 4.05> Removable Direct Access SCSI-2 device 
da0: 40.000MB/s transfers
da0: 3912MB (8013453 512 byte sectors: 255H 63S/T 498C)
cd0 at umass-sim0 bus 0 target 0 lun 1
cd0: <SanDisk U3 Cruzer Micro 4.05> Removable CD-ROM SCSI-2 device 
cd0: 40.000MB/s transfers
cd0: Attempt to query device size failed: UNIT ATTENTION, Not ready to ready change, medium may have changed
Reply With Quote