View Single Post
  #9   (View Single Post)  
Old 17th June 2010
Lexus45 Lexus45 is offline
Port Guard
 
Join Date: May 2010
Location: Kurgan, Russia
Posts: 39
Default dmesg

This is my dmesg
(I booted from CD - bsd.rd, plugged in USB-flash with FAT32, mounted it and copied the dmesg output)
Code:
OpenBSD 4.7 (RAMDISK_CD) #353: Wed Mar 17 21:02:53 MDT 2010
    deraadt@i386.openbsd.org:/usr/src/sys/arch/i386/compile/RAMDISK_CD
cpu0: Intel(R) Celeron(R) CPU 220 @ 1.20GHz ("GenuineIntel" 686-class) 1.21 GHz
cpu0: FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,TM,SBF,SSE3,MWAIT,DS-CPL,TM2,CX16,xTPR
real mem  = 496533504 (473MB)
avail mem = 474226688 (452MB)
mainbus0 at root
bios0 at mainbus0: AT/286+ BIOS, date 11/06/07, SMBIOS rev. 2.4 @ 0xe4da0 (23 entries)
bios0: vendor Intel Corp. version "LY66210M.86A.0134.2007.1106.1743" date 11/06/2007
bios0: Intel Corporation D201GLY
acpi0 at bios0: rev 0
acpi0: tables DSDT FACP APIC
acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat
cpu0 at mainbus0: apid 0 (boot processor)
cpu0: apic clock running at 133MHz
ioapic0 at mainbus0: apid 4 pa 0xfec00000, version 14, 24 pins
ioapic0: misconfigured as apic 0, remapped to apid 4
acpiprt0 at acpi0: bus 0 (PCI0)
acpiprt1 at acpi0: bus 1 (P0P1)
bios0: ROM list: 0xc0000/0x10000 0xd0000/0xa000
pci0 at mainbus0 bus 0: configuration mode 1 (bios)
pchb0 at pci0 dev 0 function 0 "SiS 662 PCI" rev 0x01
ppb0 at pci0 dev 1 function 0 "SiS 648FX AGP" rev 0x00
pci1 at ppb0 bus 1
vga1 at pci1 dev 0 function 0 "SiS 6330 VGA" rev 0x04
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
pcib0 at pci0 dev 2 function 0 "SiS 964 ISA" rev 0x36
pciide0 at pci0 dev 2 function 5 "SiS 5513 EIDE" rev 0x01: 964: DMA, channel 0 wired to compatibility, channel 1 wired to compatibility
atapiscsi0 at pciide0 channel 0 drive 1
scsibus0 at atapiscsi0: 2 targets
cd0 at scsibus0 targ 0 lun 0: <SONY, CD-RW CRX230E, QYS1> ATAPI 5/cdrom removable
cd0(pciide0:0:1): using PIO mode 4, Ultra-DMA mode 2
pciide0: channel 1 disabled (no drives)
ohci0 at pci0 dev 3 function 0 "SiS 5597/5598 USB" rev 0x0f: apic 4 int 20 (irq 11), version 1.0, legacy support
ohci1 at pci0 dev 3 function 1 "SiS 5597/5598 USB" rev 0x0f: apic 4 int 21 (irq 11), version 1.0, legacy support
ohci2 at pci0 dev 3 function 2 "SiS 5597/5598 USB" rev 0x0f: apic 4 int 22 (irq 10), version 1.0, legacy support
ehci0 at pci0 dev 3 function 3 "SiS 7002 USB" rev 0x00: apic 4 int 23 (irq 11)
ehci0: timed out waiting for BIOS
usb0 at ehci0: USB revision 2.0
uhub0 at usb0 "SiS EHCI root hub" rev 2.00/1.00 addr 1
sis0 at pci0 dev 4 function 0 "SiS 900 10/100BaseTX" rev 0x91: apic 4 int 19 (irq 10), address 00:1c:c0:6e:07:c6
brgphy0 at sis0 phy 1: BCM54XX 10/100/1000baseT PHY, rev. 1
ppb1 at pci0 dev 31 function 0 "SiS PCI-PCI" rev 0x00
pci2 at ppb1 bus 2
isa0 at pcib0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
usb1 at ohci0: USB revision 1.0
uhub1 at usb1 "SiS OHCI root hub" rev 1.00/1.00 addr 1
usb2 at ohci1: USB revision 1.0
uhub2 at usb2 "SiS OHCI root hub" rev 1.00/1.00 addr 1
usb3 at ohci2: USB revision 1.0
uhub3 at usb3 "SiS OHCI root hub" rev 1.00/1.00 addr 1
rd0: fixed, 3800 blocks
softraid0 at root
root on rd0a swap on rd0b dump on rd0b
umass0 at uhub0 port 6 configuration 1 interface 0 "Kingston DataTraveler 2.0" rev 2.00/1.00 addr 2
umass0: using SCSI over Bulk-Only
scsibus1 at umass0: 2 targets, initiator 0
sd0 at scsibus1 targ 1 lun 0: <Kingston, DataTraveler 2.0, 1.00> SCSI2 0/direct removable
sd0: 489MB, 512 bytes/sec, 1001472 sec total
sd0 detached
scsibus1 detached
umass0 detached
umass0 at uhub0 port 6 configuration 1 interface 0 "Kingston DataTraveler 2.0" rev 2.00/1.00 addr 2
umass0: using SCSI over Bulk-Only
scsibus1 at umass0: 2 targets, initiator 0
sd0 at scsibus1 targ 1 lun 0: <Kingston, DataTraveler 2.0, 1.00> SCSI2 0/direct removable
sd0: 489MB, 512 bytes/sec, 1001472 sec total
PS: and yes.. I think the problem is in my mini-ITX motherboard, because the system is not working well (it restarts on and on...) not only when using USB-boot, but also after connecting a HDD with already well-installed OBSD 4.7 (it worked fine with another motherboard & CPU, not mini-ITX).

The reason shouldn't also be in memory, because yesterday I ran memtest for 5+ hours (from Xubuntu live-CD) and everything was fine.

PS2: just now I tried with NetBSD 5.0.2 (the latest release) and the PC also restarted. On the other hand, Xubuntu 7.10 Live-CD (not new version) started well on my hardware. SLAX Linux also started well yesterday, from a USB-stick.

So, I consider to think that Intel D201GLY2 is not supported yet well enough by Open- and NetBSD (I haven't tried Free-).

That's a pity, but not a real problem. I want to set up a small home server with hosting a tiny website, smtp/pop3 daemons, OpenVPN running on it and also doing NAT for my other home PCs. If *BSD don't support this little motherboard, I'll use SLAX.

Last edited by Lexus45; 17th June 2010 at 08:37 AM.
Reply With Quote