View Single Post
  #1   (View Single Post)  
Old 9th February 2009
Quaxo Quaxo is offline
Port Guard
 
Join Date: Jun 2008
Posts: 29
Unhappy My D-Link DFE530TX ethernet adapter isnt found. Help!

Hello

In an older hardware setup (I dont remember the OpenBSD version) I used a D-Link DFE530TX REV-C1 10/100Mb ethernet adapter. It worked just fine and was recognized by OpenBSD as "vr0". But now when I install this adapter into my "new" server (OpenBSD v4.4) its not found. This is what the dmesg.boot looks like...

Code:
OpenBSD 4.4 (GENERIC) #1021: Tue Aug 12 17:16:55 MDT 2008
    deraadt@i386.openbsd.org:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: Intel(R) Celeron(R) CPU 440 @ 2.00GHz ("GenuineIntel" 686-class) 2.01 GHz
cpu0: FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,TM,SBF,SSE3,MWAIT,DS-CPL,TM2,CX16,xTPR
real mem  = 2077782016 (1981MB)
avail mem = 2000572416 (1907MB)
mainbus0 at root
bios0 at mainbus0: AT/286+ BIOS, date 11/07/07, BIOS32 rev. 0 @ 0xfb180, SMBIOS rev. 2.4 @ 0xf0100 (30 entries)
bios0: vendor Award Software International, Inc. version "F3" date 11/07/2007
bios0: Gigabyte Technology Co., Ltd. GA-73PVM-S2H
apm0 at bios0: Power Management spec V1.2 (slowidle)
apm0: AC on, battery charge unknown
acpi at bios0 function 0x0 not configured
pcibios0 at bios0: rev 3.0 @ 0xf0000/0xd7d4
pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xfd700/208 (11 entries)
pcibios0: PCI Exclusive IRQs: 5 10 11
pcibios0: no compatible PCI ICU found
pcibios0: Warning, unable to fix up PCI interrupt routing
pcibios0: PCI bus #4 is the last bus
WARNING: unknown PCI device header 0x40.
WARNING: unknown PCI device header 0x40.
WARNING: unknown PCI device header 0x40.
bios0: ROM list: 0xc0000/0xde00
cpu0 at mainbus0
pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
pchb0 at pci0 dev 0 function 0 vendor "NVIDIA", unknown product 0x07c1 rev 0xa2
"NVIDIA MCP73 Memory" rev 0xa2 at pci0 dev 0 function 1 not configured
"NVIDIA MCP73 Memory" rev 0xa1 at pci0 dev 1 function 0 not configured
"NVIDIA MCP73 Memory" rev 0xa1 at pci0 dev 1 function 1 not configured
"NVIDIA MCP73 Memory" rev 0xa1 at pci0 dev 1 function 2 not configured
"NVIDIA MCP73 Memory" rev 0xa1 at pci0 dev 1 function 3 not configured
"NVIDIA MCP73 Memory" rev 0xa1 at pci0 dev 1 function 4 not configured
"NVIDIA MCP73 Memory" rev 0xa1 at pci0 dev 1 function 5 not configured
"NVIDIA MCP73 Memory" rev 0xa1 at pci0 dev 1 function 6 not configured
"NVIDIA MCP73 Memory" rev 0xa1 at pci0 dev 2 function 0 not configured
pcib0 at pci0 dev 3 function 0 "NVIDIA MCP73 ISA" rev 0xa2
nviic0 at pci0 dev 3 function 1 "NVIDIA MCP73 SMBus" rev 0xa1
iic0 at nviic0
spdmem0 at iic0 addr 0x50: 1GB DDR2 SDRAM non-parity PC2-6400CL5
spdmem1 at iic0 addr 0x51: 1GB DDR2 SDRAM non-parity PC2-6400CL5
iic1 at nviic0
"NVIDIA MCP73 Memory" rev 0xa1 at pci0 dev 3 function 2 not configured
"NVIDIA MCP73 Memory" rev 0xa1 at pci0 dev 3 function 4 not configured
ohci0 at pci0 dev 4 function 0 "NVIDIA MCP73 USB" rev 0xa1: irq 5, version 1.0, legacy support
ehci0 at pci0 dev 4 function 1 "NVIDIA MCP73 USB" rev 0xa1: irq 10
usb0 at ehci0: USB revision 2.0
uhub0 at usb0 "NVIDIA EHCI root hub" rev 2.00/1.00 addr 1
pciide0 at pci0 dev 8 function 0 "NVIDIA MCP73 IDE" rev 0xa1: DMA, channel 0 configured to compatibility, channel 1 configured to compatibility
atapiscsi0 at pciide0 channel 0 drive 0
scsibus0 at atapiscsi0: 2 targets, initiator 7
cd0 at scsibus0 targ 0 lun 0: <TSSTcorp, CDDVDW SH-S202J, SB01> ATAPI 5/cdrom removable
cd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 4
pciide0: channel 1 ignored (disabled)
azalia0 at pci0 dev 9 function 0 "NVIDIA MCP73 HD Audio" rev 0xa1: irq 5
azalia0: /usr/src/sys/dev/pci/azalia.c/1348 invalid PCM format: 0x00000000
azalia0: codec[s]: Realtek/0x0885, NVIDIA/0x8001, using Realtek/0x0885
audio0 at azalia0
ppb0 at pci0 dev 10 function 0 "NVIDIA MCP73 PCIE" rev 0xa1
pci1 at ppb0 bus 1
ral0 at pci1 dev 5 function 0 "Ralink RT2561S" rev 0x00: irq 11, address 00:22:6b:a0:fb:19
ral0: MAC/BBP RT2561C, RF RT2527
"TI TSB43AB23 FireWire" rev 0x00 at pci1 dev 7 function 0 not configured
ppb1 at pci0 dev 11 function 0 "NVIDIA MCP73 PCIE" rev 0xa1
pci2 at ppb1 bus 2
ppb2 at pci0 dev 12 function 0 "NVIDIA MCP73 PCIE" rev 0xa1
pci3 at ppb2 bus 3
ppb3 at pci0 dev 13 function 0 "NVIDIA MCP73 PCIE" rev 0xa1
pci4 at ppb3 bus 4
pciide1 at pci0 dev 14 function 0 "NVIDIA MCP73 AHCI" rev 0xa2: DMA (unsupported), channel 0 wired to native-PCI, channel 1 wired to native-PCI
pciide1: using irq 11 for native-PCI interrupt
wd0 at pciide1 channel 0 drive 0: <ST3500320NS>
wd0: 16-sector PIO, LBA48, 476938MB, 976771055 sectors
wd1 at pciide1 channel 0 drive 1: <ST3500320NS>
wd1: 16-sector PIO, LBA48, 476940MB, 976773168 sectors
pciide1: channel 1 ignored (not responding; disabled or no drives?)
nfe0 at pci0 dev 15 function 0 "NVIDIA MCP73 LAN" rev 0xa2: irq 15, address 00:1a:4d:56:2d:8c
rgephy0 at nfe0 phy 1: RTL8169S/8110S PHY, rev. 2
vga1 at pci0 dev 16 function 0 vendor "NVIDIA", unknown product 0x07e1 rev 0xa2
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
drm at vga1 unsupported
isa0 at pcib0
isadma0 at isa0
com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
spkr0 at pcppi0
lpt0 at isa0 port 0x378/4 irq 7
it0 at isa0 port 0x2e/2: IT8718F rev 0x04, EC port 0x290
npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
usb1 at ohci0: USB revision 1.0
uhub1 at usb1 "NVIDIA OHCI root hub" rev 1.00/1.00 addr 1
biomask 7f6d netmask ff6d ttymask ffff
mtrr: Pentium Pro MTRR support
softraid0 at root
root on wd0a swap on wd0b dump on wd0b
I figure "WARNING: unknown PCI device header 0x40." is the problem. But I dont understand why it worked before and not now. I have checked the BIOS but I didnt found any odd settings there.

I also added acpid_flags="" to rc.conf.local but that didnt help (I dont know what "acpi at bios0 function 0x0 not configured" in dmesg.boot really means though; ACPI is enabled as much as possible in BIOS).

Anyone who got an idea of how to fix this?

If you find more things (from reading the dmesg.boot above) that I can fix easy, any help is welcome


Thanks in advance
/Quaxo
Reply With Quote