Hi jggimi
Here is the result from running
smartctl -a /dev/wd0c
Code:
smartctl version 5.38 [x86_64-unknown-openbsd4.4] Copyright (C) 2002-8 Bruce All
en
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Device Model: FUJITSU MHY2250BH
Serial Number: K413T842NJ4R
Firmware Version: 890B
User Capacity: 250,059,350,016 bytes
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: 8
ATA Standard is: ATA-8-ACS revision 3f
Local Time is: Fri Jan 2 16:56:41 2009 EST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (1009) seconds.
Offline data collection
capabilities: (0x51) SMART execute Offline immediate.
No Auto Offline data collection support.
Suspend Offline collection upon new
command.
No Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 143) minutes.
SCT capabilities: (0x003f) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_
FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 100 100 046 Pre-fail Always -
60550
2 Throughput_Performance 0x0005 100 100 030 Pre-fail Offline -
53411840
3 Spin_Up_Time 0x0003 100 100 025 Pre-fail Always -
1
4 Start_Stop_Count 0x0032 099 099 000 Old_age Always -
394
5 Reallocated_Sector_Ct 0x0033 100 100 024 Pre-fail Always -
8589934592000
7 Seek_Error_Rate 0x000f 100 100 047 Pre-fail Always -
1538
8 Seek_Time_Performance 0x0005 100 100 019 Pre-fail Offline -
0
9 Power_On_Hours 0x0032 097 097 000 Old_age Always -
1871
10 Spin_Retry_Count 0x0013 100 100 020 Pre-fail Always -
0
11 Calibration_Retry_Count 0x0032 253 253 000 Old_age Always -
0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always -
378
182 Unknown_Attribute 0x0032 100 100 000 Old_age Always -
0
184 Unknown_Attribute 0x0033 253 253 097 Pre-fail Always -
0
185 Unknown_Attribute 0x0010 253 253 000 Old_age Offline -
0
186 Unknown_Attribute 0x0032 253 253 000 Old_age Always -
0
187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always -
42949672960
188 Unknown_Attribute 0x0032 100 100 000 Old_age Always -
0
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always -
0
190 Airflow_Temperature_Cel 0x0022 057 045 000 Old_age Always -
43 (Lifetime Min/Max 20/45)
191 G-Sense_Error_Rate 0x0032 253 253 000 Old_age Always -
16580608
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always -
2031647
193 Load_Cycle_Count 0x0032 099 099 000 Old_age Always -
35569
195 Hardware_ECC_Recovered 0x001a 100 100 000 Old_age Always -
16
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always -
445448192
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always -
0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline -
0
199 UDMA_CRC_Error_Count 0x003e 200 253 000 Old_age Always -
0
200 Multi_Zone_Error_Rate 0x000f 100 100 060 Pre-fail Always -
6691
203 Run_Out_Cancel 0x0002 100 100 000 Old_age Always -
3732259668357
240 Head_Flying_Hours 0x003e 200 200 000 Old_age Always -
0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.