DaemonForums  

Go Back   DaemonForums > FreeBSD > FreeBSD Installation and Upgrading

FreeBSD Installation and Upgrading Installing and upgrading FreeBSD.

Reply
 
Thread Tools Display Modes
  #1   (View Single Post)  
Old 12th July 2008
mfaridi's Avatar
mfaridi mfaridi is offline
Spam Deminer
 
Join Date: May 2008
Location: Afghanistan
Posts: 282
Thanked 5 Times in 5 Posts
Default compile kernel error

I use FreeBSD 7 and I try enable PF so put this line in kernel and start compile kernel

Code:
options         ALTQ
options         ALTQ_CBQ        # Class Bases Queuing (CBQ)
options         ALTQ_RED        # Random Early Detection (RED)
options         ALTQ_RIO        # RED In/Out
options         ALTQ_HFSC       # Hierarchical Packet Scheduler (HFSC)
options         ALTQ_PRIQ       # Priority Queuing (PRIQ)
options         ALTQ_NOPCC      # Required for SMP build
and start compile kernel by this step

Code:
cd /usr/src/sys/i386/conf
then

Code:
cp GENERIC GMFARIDISRV
then I put this options in kernel

Code:
options         ALTQ
options         ALTQ_CBQ        # Class Bases Queuing (CBQ)
options         ALTQ_RED        # Random Early Detection (RED)
options         ALTQ_RIO        # RED In/Out
options         ALTQ_HFSC       # Hierarchical Packet Scheduler (HFSC)
options         ALTQ_PRIQ       # Priority Queuing (PRIQ)
options         ALTQ_NOPCC      # Required for SMP build
then I type

Code:
cd /usr/src
then I type

Code:
make buildkernel KERNCONF=GMFARIDISRV
and after build kernel I type

Code:
make installkernel KERNCONF=GMFARDISRV
after install kernel I reboot my system and after reboot I type this command

Code:
uname -a
and I see this

Code:
FreeBSD Mostafa.Faridi 7.0-STABLE FreeBSD 7.0-STABLE #0: Sat Jul 12 12:14:02 AFT 2008     Mostafa@Mostafa.Faridi:/usr/obj/usr/src/sys/GMFARIDISRV  i386
when I install FreeBSD my FreeBSD was RELEASE but after compile kernel FreeBSD change to STABLE

I do not want STABLE I want RELEASE so I go to

Code:
/etc/stable-supfile
and change this line

Code:
default release=cvs tag=RELENG_7
to

Code:
default release=cvs tag=RELENG_7_0
and start compile again

when I type

Code:
make buildkernel KERNCONF=GMFARIDISRV
I see this error

Code:
Mostafa# make buildkernel KERNCONF=GMFARIDISRV

--------------------------------------------------------------
>>> Kernel build for GMFARIDISRV started on Sat Jul 12 20:01:53 AFT 2008
--------------------------------------------------------------
===> GMFARIDISRV
mkdir -p /usr/obj/usr/src/sys

--------------------------------------------------------------
>>> stage 1: configuring the kernel
--------------------------------------------------------------
cd /usr/src/sys/i386/conf;  PATH=/usr/obj/usr/src/tmp/legacy/usr/sbin:/usr/obj/usr/src/tmp/legacy/usr/bin:/usr/obj/usr/src/tmp/legacy/usr/games:/usr/obj/usr/src/tmp/usr/sbin:/usr/obj/usr/src/tmp/usr/bin:/usr/obj/usr/src/tmp/usr/games:/sbin:/bin:/usr/sbin:/usr/bin  config  -d /usr/obj/usr/src/sys/GMFARIDISRV  /usr/src/sys/i386/conf/GMFARIDISRV
/usr/src/sys/i386/conf/GMFARIDISRV: unknown option "STACK"
*** Error code 1

Stop in /usr/src.
*** Error code 1

Stop in /usr/src.
and I can not compile kernel again

which stage I make mistake ??

I do not like STABLE and I want use only RELEASE
Reply With Quote
  #2   (View Single Post)  
Old 12th July 2008
graudeejs's Avatar
graudeejs graudeejs is offline
Real Name: Aldis Berjoza
formerly killasmurf86
 
Join Date: Jul 2008
Location: Riga, Latvia
Posts: 588
Thanked 29 Times in 26 Posts
Default

post entire kernel config... if you have modified more than what you showed here
Reply With Quote
  #3   (View Single Post)  
Old 13th July 2008
ninjatux's Avatar
ninjatux ninjatux is offline
Real Name: Baqir Majlisi
Spam Deminer
 
Join Date: May 2008
Location: Antarctica
Posts: 293
Thanked 15 Times in 15 Posts
Default

Seems you've specified an unsupported or nonexistent option in your kernel configuration. Post the entire file as killasmurf suggested.
__________________
"UNIX is basically a simple operating system, but you have to be a genius to understand the simplicity."
MacBook Pro (Darwin 9), iMac (Darwin 9), iPod Touch (Darwin 9), Dell Optiplex GX620 (FreeBSD 7.1-STABLE)
Reply With Quote
  #4   (View Single Post)  
Old 13th July 2008
mfaridi's Avatar
mfaridi mfaridi is offline
Spam Deminer
 
Join Date: May 2008
Location: Afghanistan
Posts: 282
Thanked 5 Times in 5 Posts
Default

This is my kernel conf

Code:
#
# GENERIC -- Generic kernel configuration file for FreeBSD/i386
#
# For more information on this file, please read the handbook section on
# Kernel Configuration Files:
#
#    http://www.FreeBSD.org/doc/en_US.ISO8859-1/books/handbook/kernelconfig-config.html
#
# The handbook is also available locally in /usr/share/doc/handbook
# if you've installed the doc distribution, otherwise always see the
# FreeBSD World Wide Web server (http://www.FreeBSD.org/) for the
# latest information.
#
# An exhaustive list of options and more detailed explanations of the
# device lines is also present in the ../../conf/NOTES and NOTES files.
# If you are in doubt as to the purpose or necessity of a line, check first
# in NOTES.
#
# $FreeBSD: src/sys/i386/conf/GENERIC,v 1.474.2.8 2008/07/04 01:29:12 delphij Exp $

cpu             I486_CPU
cpu             I586_CPU
cpu             I686_CPU
ident           GMFARIDISRV

# To statically compile in device wiring instead of /boot/device.hints
#hints          "GENERIC.hints"         # Default places to look for devices.

makeoptions     DEBUG=-g                # Build kernel with gdb(1) debug symbols

options         SCHED_ULE               # ULE scheduler
options         PREEMPTION              # Enable kernel thread preemption
options         INET                    # InterNETworking
options         INET6                   # IPv6 communications protocols
options         SCTP                    # Stream Control Transmission Protocol
options         FFS                     # Berkeley Fast Filesystem
options         SOFTUPDATES             # Enable FFS soft updates support
options         UFS_ACL                 # Support for access control lists
options         UFS_DIRHASH             # Improve performance on big directories
options         UFS_GJOURNAL            # Enable gjournal-based UFS journaling
options         MD_ROOT                 # MD is a potential root device
options         NFSCLIENT               # Network Filesystem Client
options         NFSSERVER               # Network Filesystem Server
options         NFSLOCKD                # Network Lock Manager
options 	NFS_ROOT		# NFS usable as /, requires NFSCLIENT
options 	MSDOSFS			# MSDOS Filesystem
options 	CD9660			# ISO 9660 Filesystem
options 	PROCFS			# Process filesystem (requires PSEUDOFS)
options 	PSEUDOFS		# Pseudo-filesystem framework
options 	GEOM_PART_GPT		# GUID Partition Tables.
options 	GEOM_LABEL		# Provides labelization
options 	COMPAT_43TTY		# BSD 4.3 TTY compat [KEEP THIS!]
options 	COMPAT_FREEBSD4		# Compatible with FreeBSD4
options 	COMPAT_FREEBSD5		# Compatible with FreeBSD5
options 	COMPAT_FREEBSD6		# Compatible with FreeBSD6
options 	SCSI_DELAY=5000		# Delay (in ms) before probing SCSI
options 	KTRACE			# ktrace(1) support
options 	STACK			# stack(9) support
options 	SYSVSHM			# SYSV-style shared memory
options 	SYSVMSG			# SYSV-style message queues
options 	SYSVSEM			# SYSV-style semaphores
options 	_KPOSIX_PRIORITY_SCHEDULING # POSIX P1003_1B real-time extensions
options 	KBD_INSTALL_CDEV	# install a CDEV entry in /dev
options 	ADAPTIVE_GIANT		# Giant mutex is adaptive.
options 	STOP_NMI		# Stop CPUS using NMI instead of IPI
options 	AUDIT			# Security event auditing
options         ALTQ
options         ALTQ_CBQ        # Class Bases Queuing (CBQ)
options         ALTQ_RED        # Random Early Detection (RED)
options         ALTQ_RIO        # RED In/Out
options         ALTQ_HFSC       # Hierarchical Packet Scheduler (HFSC)
options         ALTQ_PRIQ       # Priority Queuing (PRIQ)
options         ALTQ_NOPCC      # Required for SMP build
options         QUOTA


# To make an SMP kernel, the next two lines are needed
options 	SMP			# Symmetric MultiProcessor Kernel
device		apic			# I/O APIC

# PF Device
device pf
device pflog
device pfsync


# CPU frequency control
device		cpufreq

# Bus support.
device		eisa
device		pci

# Floppy drives
device		fdc

# ATA and ATAPI devices
device		ata
device		atadisk		# ATA disk drives
device		ataraid		# ATA RAID drives
device		atapicd		# ATAPI CDROM drives
device		atapifd		# ATAPI floppy drives
device		atapist		# ATAPI tape drives
options 	ATA_STATIC_ID	# Static device numbering

# SCSI Controllers
device		ahb		# EISA AHA1742 family
device		ahc		# AHA2940 and onboard AIC7xxx devices
options 	AHC_REG_PRETTY_PRINT	# Print register bitfields in debug
					# output.  Adds ~128k to driver.
device		ahd		# AHA39320/29320 and onboard AIC79xx devices
options 	AHD_REG_PRETTY_PRINT	# Print register bitfields in debug
					# output.  Adds ~215k to driver.
device		amd		# AMD 53C974 (Tekram DC-390(T))
device		hptiop		# Highpoint RocketRaid 3xxx series
device		isp		# Qlogic family
#device 	ispfw		# Firmware for QLogic HBAs- normally a module
device		mpt		# LSI-Logic MPT-Fusion
#device		ncr		# NCR/Symbios Logic
device		sym		# NCR/Symbios Logic (newer chipsets + those of `ncr')
device		trm		# Tekram DC395U/UW/F DC315U adapters

device		adv		# Advansys SCSI adapters
device		adw		# Advansys wide SCSI adapters
device		aha		# Adaptec 154x SCSI adapters
device		aic		# Adaptec 15[012]x SCSI adapters, AIC-6[23]60.
device		bt		# Buslogic/Mylex MultiMaster SCSI adapters

device		ncv		# NCR 53C500
device		nsp		# Workbit Ninja SCSI-3
device		stg		# TMC 18C30/18C50

# SCSI peripherals
device		scbus		# SCSI bus (required for SCSI)
device		ch		# SCSI media changers
device		da		# Direct Access (disks)
device		sa		# Sequential Access (tape etc)
device		cd		# CD
device		pass		# Passthrough device (direct SCSI access)
device		ses		# SCSI Environmental Services (and SAF-TE)

# RAID controllers interfaced to the SCSI subsystem
device		amr		# AMI MegaRAID
device		arcmsr		# Areca SATA II RAID
device		asr		# DPT SmartRAID V, VI and Adaptec SCSI RAID
device		ciss		# Compaq Smart RAID 5*
device		dpt		# DPT Smartcache III, IV - See NOTES for options
device		hptmv		# Highpoint RocketRAID 182x
device		hptrr		# Highpoint RocketRAID 17xx, 22xx, 23xx, 25xx
device		iir		# Intel Integrated RAID
device		ips		# IBM (Adaptec) ServeRAID
device		mly		# Mylex AcceleRAID/eXtremeRAID
device		twa		# 3ware 9000 series PATA/SATA RAID

# RAID controllers
device		aac		# Adaptec FSA RAID
device		aacp		# SCSI passthrough for aac (requires CAM)
device		ida		# Compaq Smart RAID
device		mfi		# LSI MegaRAID SAS
device		mlx		# Mylex DAC960 family
device		pst		# Promise Supertrak SX6000
device		twe		# 3ware ATA RAID

# atkbdc0 controls both the keyboard and the PS/2 mouse
device		atkbdc		# AT keyboard controller
device		atkbd		# AT keyboard
device		psm		# PS/2 mouse

device		kbdmux		# keyboard multiplexer

device		vga		# VGA video card driver

device		splash		# Splash screen and screen saver support

# syscons is the default console driver, resembling an SCO console
device		sc

device		agp		# support several AGP chipsets

# Power management support (see NOTES for more options)
#device		apm
# Add suspend/resume support for the i8254.
device		pmtimer

# PCCARD (PCMCIA) support
# PCMCIA and cardbus bridge support
device		cbb		# cardbus (yenta) bridge
device		pccard		# PC Card (16-bit) bus
device		cardbus		# CardBus (32-bit) bus

# Serial (COM) ports
device		sio		# 8250, 16[45]50 based serial ports
device		uart		# Generic UART driver

# Parallel port
device		ppc
device		ppbus		# Parallel port bus (required)
device		lpt		# Printer
device		plip		# TCP/IP over parallel
device		ppi		# Parallel port interface device
#device		vpo		# Requires scbus and da

# If you've got a "dumb" serial or parallel PCI card that is
# supported by the puc(4) glue driver, uncomment the following
# line to enable it (connects to sio, uart and/or ppc drivers):
#device		puc

# PCI Ethernet NICs.
device		de		# DEC/Intel DC21x4x (``Tulip'')
device		em		# Intel PRO/1000 adapter Gigabit Ethernet Card
device		ixgb		# Intel PRO/10GbE Ethernet Card
device		le		# AMD Am7900 LANCE and Am79C9xx PCnet
device		txp		# 3Com 3cR990 (``Typhoon'')
device		vx		# 3Com 3c590, 3c595 (``Vortex'')

# PCI Ethernet NICs that use the common MII bus controller code.
# NOTE: Be sure to keep the 'device miibus' line in order to use these NICs!
device		miibus		# MII bus support
device		bce		# Broadcom BCM5706/BCM5708 Gigabit Ethernet
device		bfe		# Broadcom BCM440x 10/100 Ethernet
device		bge		# Broadcom BCM570xx Gigabit Ethernet
device		dc		# DEC/Intel 21143 and various workalikes
device		et		# Agere ET1310 10/100/Gigabit Ethernet
device		fxp		# Intel EtherExpress PRO/100B (82557, 82558)
device		lge		# Level 1 LXT1001 gigabit Ethernet
device		msk		# Marvell/SysKonnect Yukon II Gigabit Ethernet
device		nfe		# nVidia nForce MCP on-board Ethernet
device		nge		# NatSemi DP83820 gigabit Ethernet
#device		nve		# nVidia nForce MCP on-board Ethernet Networking
device		pcn		# AMD Am79C97x PCI 10/100 (precedence over 'le')
device		re		# RealTek 8139C+/8169/8169S/8110S
device		rl		# RealTek 8129/8139
device		sf		# Adaptec AIC-6915 (``Starfire'')
device		sis		# Silicon Integrated Systems SiS 900/SiS 7016
device		sk		# SysKonnect SK-984x & SK-982x gigabit Ethernet
device		ste		# Sundance ST201 (D-Link DFE-550TX)
device		stge		# Sundance/Tamarack TC9021 gigabit Ethernet
device		ti		# Alteon Networks Tigon I/II gigabit Ethernet
device		tl		# Texas Instruments ThunderLAN
device		tx		# SMC EtherPower II (83c170 ``EPIC'')
device		vge		# VIA VT612x gigabit Ethernet
device		vr		# VIA Rhine, Rhine II
device		wb		# Winbond W89C840F
device		xl		# 3Com 3c90x (``Boomerang'', ``Cyclone'')

# ISA Ethernet NICs.  pccard NICs included.
device		cs		# Crystal Semiconductor CS89x0 NIC
# 'device ed' requires 'device miibus'
device		ed		# NE[12]000, SMC Ultra, 3c503, DS8390 cards
device		ex		# Intel EtherExpress Pro/10 and Pro/10+
device		ep		# Etherlink III based cards
device		fe		# Fujitsu MB8696x based cards
device		ie		# EtherExpress 8/16, 3C507, StarLAN 10 etc.
device		sn		# SMC's 9000 series of Ethernet chips
device		xe		# Xircom pccard Ethernet

# Wireless NIC cards
device		wlan		# 802.11 support
device		wlan_wep	# 802.11 WEP support
device		wlan_ccmp	# 802.11 CCMP support
device		wlan_tkip	# 802.11 TKIP support
device		wlan_amrr	# AMRR transmit rate control algorithm
device		wlan_scan_ap	# 802.11 AP mode scanning
device		wlan_scan_sta	# 802.11 STA mode scanning
device		an		# Aironet 4500/4800 802.11 wireless NICs.
device		ath		# Atheros pci/cardbus NIC's
device		ath_hal		# Atheros HAL (Hardware Access Layer)
device		ath_rate_sample	# SampleRate tx rate control for ath
device		awi		# BayStack 660 and others
device		ral		# Ralink Technology RT2500 wireless NICs.
device		wi		# WaveLAN/Intersil/Symbol 802.11 wireless NICs.
#device		wl		# Older non 802.11 Wavelan wireless NIC.

# Pseudo devices.
device		loop		# Network loopback
device		random		# Entropy device
device		ether		# Ethernet support
device		sl		# Kernel SLIP
device		ppp		# Kernel PPP
device		tun		# Packet tunnel.
device		pty		# Pseudo-ttys (telnet etc)
device		md		# Memory "disks"
device		gif		# IPv6 and IPv4 tunneling
device		faith		# IPv6-to-IPv4 relaying (translation)
device		firmware	# firmware assist module

# The `bpf' device enables the Berkeley Packet Filter.
# Be aware of the administrative consequences of enabling this!
# Note that 'bpf' is required for DHCP.
device		bpf		# Berkeley packet filter

# USB support
device		uhci		# UHCI PCI->USB interface
device		ohci		# OHCI PCI->USB interface
device		ehci		# EHCI PCI->USB interface (USB 2.0)
device		usb		# USB Bus (required)
#device		udbp		# USB Double Bulk Pipe devices
device		ugen		# Generic
device		uhid		# "Human Interface Devices"
device		ukbd		# Keyboard
device		ulpt		# Printer
device		umass		# Disks/Mass storage - Requires scbus and da
device		ums		# Mouse
device		ural		# Ralink Technology RT2500USB wireless NICs
device		rum		# Ralink Technology RT2501USB wireless NICs
device		urio		# Diamond Rio 500 MP3 player
device		uscanner	# Scanners
# USB Serial devices
device		ucom		# Generic com ttys
device		uark		# Technologies ARK3116 based serial adapters
device		ubsa		# Belkin F5U103 and compatible serial adapters
device		ubser		# BWCT console serial adapters
device		uftdi		# For FTDI usb serial adapters
device		uipaq		# Some WinCE based devices
device		uplcom		# Prolific PL-2303 serial adapters
device		uslcom		# SI Labs CP2101/CP2102 serial adapters
device		uvisor		# Visor and Palm devices
device		uvscom		# USB serial support for DDI pocket's PHS
# USB Ethernet, requires miibus
device		aue		# ADMtek USB Ethernet
device		axe		# ASIX Electronics USB Ethernet
device		cdce		# Generic USB over Ethernet
device		cue		# CATC USB Ethernet
device		kue		# Kawasaki LSI USB Ethernet
device		rue		# RealTek RTL8150 USB Ethernet

# FireWire support
device		firewire	# FireWire bus code
device		sbp		# SCSI over FireWire (Requires scbus and da)
device		fwe		# Ethernet over FireWire (non-standard!)
device		fwip		# IP over FireWire (RFC 2734,3146)
device		dcons		# Dumb console driver
device		dcons_crom	# Configuration ROM for dcons
Mostafa#
Reply With Quote
  #5   (View Single Post)  
Old 13th July 2008
ephemera's Avatar
ephemera ephemera is offline
Knuth's homeboy
 
Join Date: Apr 2008
Posts: 537
Thanked 49 Times in 43 Posts
Default

Quote:
options STACK # stack(9) support
this line looks suspicious to me.
how did it get there in the first place?
Reply With Quote
  #6   (View Single Post)  
Old 13th July 2008
graudeejs's Avatar
graudeejs graudeejs is offline
Real Name: Aldis Berjoza
formerly killasmurf86
 
Join Date: Jul 2008
Location: Riga, Latvia
Posts: 588
Thanked 29 Times in 26 Posts
Default

Uh, man, you haven't deleted any of unneeded drivers.....
can you also post dmesg output.....
Reply With Quote
  #7   (View Single Post)  
Old 13th July 2008
mfaridi's Avatar
mfaridi mfaridi is offline
Spam Deminer
 
Join Date: May 2008
Location: Afghanistan
Posts: 282
Thanked 5 Times in 5 Posts
Default

after I cvsup with 7_0 , I delete GNFARIDISRV kernel and make new KERNEL and modify it and began compile kernel without problem and right now my STABLE change to RELEASE

after update with cvsup I do not have stack option

but another question when I type

Code:
uname -a
I see this

Code:
FreeBSD Mostafa.Faridi 7.0-RELEASE-p2 FreeBSD 7.0-RELEASE-p2 #1: Sun Jul 13 11:16:48 AFT 2008     Mostafa@Mostafa.Faridi:/usr/obj/usr/src/sys/GMFARIDISRV  i386
I see p2

what is mean P2 ?

why I do not have only RELEASE ?
Reply With Quote
  #8   (View Single Post)  
Old 13th July 2008
graudeejs's Avatar
graudeejs graudeejs is offline
Real Name: Aldis Berjoza
formerly killasmurf86
 
Join Date: Jul 2008
Location: Riga, Latvia
Posts: 588
Thanked 29 Times in 26 Posts
Default

Code:
# uname -a
FreeBSD killasmurf.pc 7.0-RELEASE FreeBSD 7.0-RELEASE #20: Wed Jul  9 19:09:03 EEST 2008     killasmurf@killasmurf.pc:/usr/obj/usr/src/sys/killabsd  i386

My guess would be, perhaps you have patched kernel?
Reply With Quote
  #9   (View Single Post)  
Old 13th July 2008
phoenix's Avatar
phoenix phoenix is offline
Risen from the ashes
 
Join Date: May 2008
Posts: 699
Thanked 90 Times in 81 Posts
Default

tag=RELENG_7_0_0_RELEASE gives you the same source code as is used to build the release CDs. This is the release branch.

tag=RELENG_7_0 gives you the source code for the release + any security fixes that have been made since the release. This is the security branch. Each commit to this branch increases the patch level by one. Hence the -pX after the version number. This is the tag you should be using.

tag=RELENG_7 gives you the latest source code from the 7-STABLE development branch. This branch is always changing, and will eventually become 7.1, and then 7.2, etc.
__________________
Freddie

Help for FreeBSD: Handbook, FAQ, man pages, mailing lists.

Last edited by phoenix; 14th July 2008 at 05:04 AM. Reason: Spelling nits.
Reply With Quote
Old 14th July 2008
Carpetsmoker's Avatar
Carpetsmoker Carpetsmoker is offline
Real Name: Martin
Old man from scene 24
 
Join Date: Apr 2008
Location: Eindhoven, Netherlands
Posts: 2,088
Thanked 198 Times in 156 Posts
Default

The kernel config GMFARIDISRV is based on STABLE, some options (such as STACK) may have been added to STABLE that are not in RELEASE.

Here is the GENERIC config for RELENG_7
http://www.freebsd.org/cgi/cvsweb.cg...h_tag=RELENG_7

And here for RELEASE_7_0:
http://www.freebsd.org/cgi/cvsweb.cg...tag=RELENG_7_0

Use diff(1) to spot differences and merge, i.e.
% diff -u GENERIC.stable GENERIC.release
__________________
UNIX was not designed to stop you from doing stupid things, because that would also stop you from doing clever things.
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Trying to Debug C++ Compile Error [Shibboleth] on FreeBSD starbuck Programming 4 15th January 2009 10:30 PM
Kernel Compilation --> Error code 2 --> geom_part_pc98 (FreeBSD 7.0) stou FreeBSD Installation and Upgrading 15 11th October 2008 04:43 AM
Can't load kernel error on PC-BSD / FreeSBIE lazerbeat FreeBSD Installation and Upgrading 3 5th July 2008 08:39 PM
Kernel error with ieee802111 disappearedng FreeBSD General 1 29th June 2008 10:56 AM
Kernel Driver Not accesable error In Virtural Box on Ubntu hardy FloridaBSD Other BSD and UNIX/UNIX-like 8 28th May 2008 01:11 AM


All times are GMT. The time now is 06:10 PM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Content copyright © 2007-2010, the authors
Daemon image copyright ©1988, Marshall Kirk McKusick