DaemonForums  

Go Back   DaemonForums > OpenBSD > OpenBSD Installation and Upgrading

OpenBSD Installation and Upgrading Installing and upgrading OpenBSD.

Reply
 
Thread Tools Display Modes
  #1   (View Single Post)  
Old 19th May 2010
shep shep is offline
ISO Quartermaster
 
Join Date: May 2008
Location: Dry and Dusty
Posts: 546
Thanked 9 Times in 9 Posts
Default wd0 not found at install

I have been unable to install 4.6 or 4.7 on an old Asus C3 terminator with an WD 400JD-55SA1 SATA hard drive jumpered to 1.5. 4.5 would install as would 4.6 and 4.7 using ide drives.

If I use ukc to disable apm the drive is found but hangs with the dmesg
Quote:
wdc_atapi_intr: warning: reading only 14 of 18 bytes
If I do not disable apm the kernel does not hang but the pciide driver does not find any drives to install to.

I think the Via Chip set (VT6420 SATA) is kinda of buggy and I have noticed that FreeBSD 6.4 and 7.3 work but 8.0 does not (spurious interupts at irq11)

In NetBSD 5.02 I have to change the Phoenix BIOS setting to RAID for the drive to be recognized

Any suggestions to get a support version of OpenBSD running with an SATA drive would be appreciated
Reply With Quote
  #2   (View Single Post)  
Old 20th May 2010
marcolino's Avatar
marcolino marcolino is offline
Real Name: Mark
Custom Title Maker
 
Join Date: May 2008
Location: At the Mountains of Madness
Posts: 112
Thanked 0 Times in 0 Posts
Default

Did you look in the INSTALL.386 file for that particular card? The file doesn't list it.
Code:
VIA Technologies CX700, VT82C586/A/B, VT82C596A/B, VT82C686A/B,
		    VT8231, VT8366, VT8233, VT8235, VT8237, VT8237A/S, VT8251,
		    VT6410, VX700
__________________
That's nothing a couple o' pints wouldn't fix.
Reply With Quote
  #3   (View Single Post)  
Old 20th May 2010
BSDfan666 BSDfan666 is offline
Real Name: N/A, this is the interweb.
Helpful companion
 
Join Date: Apr 2008
Location: Ontario, Canada
Posts: 2,223
Thanked 193 Times in 184 Posts
Default

Neither the install page, manual page, or website can contain a complete list of supported controllers.. almost all PCI IDE controllers comply with a basic specification and should work with pciide(4).

SATA typically emulates a PCI IDE controller for support with legacy systems, but you can typically enable AHCI in the BIOS.. which will be detected by ahci(4).

In this case, your disk will be sd(4) and not wd(4).
Reply With Quote
  #4   (View Single Post)  
Old 20th May 2010
marcolino's Avatar
marcolino marcolino is offline
Real Name: Mark
Custom Title Maker
 
Join Date: May 2008
Location: At the Mountains of Madness
Posts: 112
Thanked 0 Times in 0 Posts
Default

Quote:
Originally Posted by BSDfan666 View Post
Neither the install page, manual page, or website can contain a complete list of supported controllers.. almost all PCI IDE controllers comply with a basic specification and should work with pciide(4).

SATA typically emulates a PCI IDE controller for support with legacy systems, but you can typically enable AHCI in the BIOS.. which will be detected by ahci(4).

In this case, your disk will be sd(4) and not wd(4).
If it emulates a PCI IDE controller, wouldn't it be wd(4)?
__________________
That's nothing a couple o' pints wouldn't fix.
Reply With Quote
  #5   (View Single Post)  
Old 20th May 2010
BSDfan666 BSDfan666 is offline
Real Name: N/A, this is the interweb.
Helpful companion
 
Join Date: Apr 2008
Location: Ontario, Canada
Posts: 2,223
Thanked 193 Times in 184 Posts
Default

If it's in PCI IDE controller emulation mode, yes, but as I said, if the BIOS supports it.. AHCI is an option.

If it's not showing up then there may be some other issue, he didn't post a full dmesg.
Reply With Quote
  #6   (View Single Post)  
Old 20th May 2010
shep shep is offline
ISO Quartermaster
 
Join Date: May 2008
Location: Dry and Dusty
Posts: 546
Thanked 9 Times in 9 Posts
Default

Thanks for the replies. I do not believe that my bios supports AHCI - at least no options that specifically use the term AHCI come up. I can enable on-chip SATA and if SATA is set IDE or RAID. I have the latest BIOS installed.

It is interesting that FreeBSD, OpenBSD and NetBSD all treat the driver specification differently. It works with out issues with FreeBSD 6.4/7.3 and Linux, requires an on-chip softraid setting in NetBSD and does not work at all in OpenBSD or FreeBSD 8.0


I went ahead in put FreeBSD 7.3 in.
Reply With Quote
  #7   (View Single Post)  
Old 1st June 2010
iFrag iFrag is offline
New User
 
Join Date: Jun 2010
Posts: 2
Thanked 0 Times in 0 Posts
Default

I have this same problem when trying to boot the 4.7 release from i386/install47.iso.

Same chip (VT6420 SATA) and error (wdc_atapi_intr: warning: reading only 14 of 18 bytes) during boot. I'm not really clear on how to even post a dmesg of this issue because it hangs at this point, and does not continue booting like normal. If a dmesg included from 4.6 is still useful for something I can include that for reference (other than the error I think it looks mostly the same up to that point).

However, I have been running OpenBSD 4.6-Release and now I have updated to OpenBSD 4.6-Stable and both run relatively OK on my configuration. About once every couple months I was having some issue with the machine hanging, which I was hoping was resolved by something in 4.7. Failing to install that I decided my next best option was at least updating to 4.6-Stable, to see if perhaps one of those fixes covered my problem.

In regards to hardware listings (marcolino's post), I poked around a little and in pciide.c and there is an entry for it in the pciide_product_desc pciide_via_products structure:

{ PCI_PRODUCT_VIATECH_VT6420_SATA, /* VIA VT6420 SATA */
0,
sata_chip_map
}

So I'm guessing just the usual standard in this case?
Reply With Quote
  #8   (View Single Post)  
Old 1st June 2010
iFrag iFrag is offline
New User
 
Join Date: Jun 2010
Posts: 2
Thanked 0 Times in 0 Posts
Default

This is the only one I can retrieve at the moment. Somewhere after the pciide lines is where 4.7 boot would lockup with the bytes read error.

Code:
OpenBSD 4.6-stable (GENERIC) #0: Mon May 31 18:12:40 EST 2010
    root@mika.wired.net:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: VIA Eden Processor 1200MHz ("CentaurHauls" 686-class) 1.21 GHz
cpu0: FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,APIC,SEP,MTRR,PGE,CMOV,PAT,CFLUSH,ACPI,MMX,FXSR,SSE,SSE2,TM,SBF,SSE3,EST,TM2,xTPR
real mem  = 468152320 (446MB)
avail mem = 443731968 (423MB)
mainbus0 at root
bios0 at mainbus0: AT/286+ BIOS, date 11/25/08, BIOS32 rev. 0 @ 0xfa340, SMBIOS rev. 2.3 @ 0xf0000 (33 entries)
bios0: vendor Phoenix Technologies, LTD version "6.00 PG" date 11/25/2008
apm0 at bios0: Power Management spec V1.2 (slowidle)
apm0: AC on, battery charge unknown
acpi at bios0 function 0x0 not configured
pcibios0 at bios0: rev 2.1 @ 0xf0000/0xc7f4
pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xfc720/208 (11 entries)
pcibios0: bad IRQ table checksum
pcibios0: PCI BIOS has 11 Interrupt Routing table entries
pcibios0: PCI Exclusive IRQs: 5 10 11
pcibios0: PCI Interrupt Router at 000:17:0 ("VIA VT8237 ISA" rev 0x00)
pcibios0: PCI bus #1 is the last bus
bios0: ROM list: 0xc0000/0x10000
cpu0 at mainbus0: (uniprocessor)
cpu0: RNG AES AES-CTR SHA1 SHA256 RSA
cpu0: unknown Enhanced SpeedStep CPU, msr 0x04090c0a04000c0a
cpu0: using only highest and lowest power states
cpu0: Enhanced SpeedStep 1201 MHz: speeds: 1600, 533 MHz
pci0 at mainbus0 bus 0: configuration mode 1 (bios)
pchb0 at pci0 dev 0 function 0 "VIA CN700 Host" rev 0x00
viaagp0 at pchb0: v3
agp0 at viaagp0: aperture at 0xe8000000, size 0x10000000
pchb1 at pci0 dev 0 function 1 "VIA CN700 Host" rev 0x00
pchb2 at pci0 dev 0 function 2 "VIA CN700 Host" rev 0x00
pchb3 at pci0 dev 0 function 3 "VIA PT890 Host" rev 0x00
pchb4 at pci0 dev 0 function 4 "VIA CN700 Host" rev 0x00
pchb5 at pci0 dev 0 function 7 "VIA CN700 Host" rev 0x00
ppb0 at pci0 dev 1 function 0 "VIA VT8377 AGP" rev 0x00
pci1 at ppb0 bus 1
vga1 at pci1 dev 0 function 0 "VIA S3 Unichrome PRO IGP" rev 0x01
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
re0 at pci0 dev 9 function 0 "Realtek 8169SC" rev 0x10: RTL8169/8110SCd (0x1800), irq 5, address 00:30:18:a7:b5:08
rgephy0 at re0 phy 7: RTL8169S/8110S PHY, rev. 2
re1 at pci0 dev 11 function 0 "Realtek 8169SC" rev 0x10: RTL8169/8110SCd (0x1800), irq 10, address 00:30:18:a7:b5:09
rgephy1 at re1 phy 7: RTL8169S/8110S PHY, rev. 2
pciide0 at pci0 dev 15 function 0 "VIA VT6420 SATA" rev 0x80: DMA
pciide0: using irq 11 for native-PCI interrupt
atapiscsi0 at pciide0 channel 0 drive 0
scsibus0 at atapiscsi0: 2 targets
cd0 at scsibus0 targ 0 lun 0: <TSSTcorp, CDDVDW SH-S223B, SB02> ATAPI 5/cdrom removable
cd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 5
wd0 at pciide0 channel 1 drive 0: <WDC WD1600AAJS-00B4A0>
wd0: 16-sector PIO, LBA48, 152627MB, 312581808 sectors
wd0(pciide0:1:0): using PIO mode 4, Ultra-DMA mode 5
pciide1 at pci0 dev 15 function 1 "VIA VT82C571 IDE" rev 0x06: ATA133, channel 0 configured to compatibility, channel 1 configured to compatibility
pciide1: channel 0 disabled (no drives)
pciide1: channel 1 ignored (disabled)
uhci0 at pci0 dev 16 function 0 "VIA VT83C572 USB" rev 0x81: irq 11
uhci1 at pci0 dev 16 function 1 "VIA VT83C572 USB" rev 0x81: irq 11
uhci2 at pci0 dev 16 function 2 "VIA VT83C572 USB" rev 0x81: irq 11
uhci3 at pci0 dev 16 function 3 "VIA VT83C572 USB" rev 0x81: irq 11
ehci0 at pci0 dev 16 function 4 "VIA VT6202 USB" rev 0x86: irq 5
usb0 at ehci0: USB revision 2.0
uhub0 at usb0 "VIA EHCI root hub" rev 2.00/1.00 addr 1
viapm0 at pci0 dev 17 function 0 "VIA VT8237 ISA" rev 0x00
iic0 at viapm0
spdmem0 at iic0 addr 0x50: 1GB DDR2 SDRAM non-parity PC2-4200CL5
auvia0 at pci0 dev 17 function 5 "VIA VT8233 AC97" rev 0x60: irq 5
ac97: codec id 0x414c4760 (Avance Logic ALC655 rev 0)
audio0 at auvia0
usb1 at uhci0: USB revision 1.0
uhub1 at usb1 "VIA UHCI root hub" rev 1.00/1.00 addr 1
usb2 at uhci1: USB revision 1.0
uhub2 at usb2 "VIA UHCI root hub" rev 1.00/1.00 addr 1
usb3 at uhci2: USB revision 1.0
uhub3 at usb3 "VIA UHCI root hub" rev 1.00/1.00 addr 1
usb4 at uhci3: USB revision 1.0
uhub4 at usb4 "VIA UHCI root hub" rev 1.00/1.00 addr 1
isa0 at mainbus0
isadma0 at isa0
com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
com0: probed fifo depth: 15 bytes
com1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
com1: probed fifo depth: 15 bytes
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
spkr0 at pcppi0
lpt0 at isa0 port 0x378/4 irq 7
fins0 at isa0 port 0x4e/2
npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
biomask fb65 netmask ff65 ttymask ffff
mtrr: Pentium Pro MTRR support
uhidev0 at uhub2 port 1 configuration 1 interface 0 "Dell Dell USB Keyboard" rev 1.10/3.01 addr 2
uhidev0: iclass 3/1
ukbd0 at uhidev0: 8 modifier keys, 6 key codes
wskbd1 at ukbd0 mux 1
wskbd1: connecting to wsdisplay0
uhidev1 at uhub1 port 2 configuration 1 interface 0 "Logitech USB-PS/2 Optical Mouse" rev 2.00/22.00 addr 2
uhidev1: iclass 3/1
ums0 at uhidev1: 8 buttons, Z dir
wsmouse0 at ums0 mux 0
softraid0 at root
root on wd0a swap on wd0b dump on wd0b
Reply With Quote
  #9   (View Single Post)  
Old 15th June 2010
shep shep is offline
ISO Quartermaster
 
Join Date: May 2008
Location: Dry and Dusty
Posts: 546
Thanked 9 Times in 9 Posts
Default

Some Persistence at least lead to an explanation but unfortunately not a solution

http://old.nabble.com/kernel-6117:-S...p22815411.html

Last edited by shep; 15th June 2010 at 03:28 AM. Reason: Learn to spell
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
mk.conf not found mtm0 NetBSD Package System (pkgsrc) 2 4th September 2009 04:42 PM
kernel not found isamu FreeBSD Installation and Upgrading 13 24th October 2008 12:24 AM
I finally found it!!! crayoxide FreeBSD General 8 23rd July 2008 05:41 AM
pkg-get command not found whispersGhost Solaris 2 11th June 2008 01:06 PM
xorgcfg command not found Lazy FreeBSD Installation and Upgrading 10 21st May 2008 08:47 PM


All times are GMT. The time now is 04:45 AM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Content copyright © 2007-2010, the authors
Daemon image copyright ©1988, Marshall Kirk McKusick