DaemonForums  

Go Back   DaemonForums > OpenBSD > OpenBSD Installation and Upgrading

OpenBSD Installation and Upgrading Installing and upgrading OpenBSD.

Reply
 
Thread Tools Display Modes
  #1   (View Single Post)  
Old 13th February 2012
shep shep is offline
ISO Quartermaster
 
Join Date: May 2008
Location: Dry and Dusty
Posts: 611
Thanked 9 Times in 9 Posts
Default OpenBSD 5.0 and Current i386 buggy acpi tables

In am trying to use OpenBSD in an Everex 1500 Stepnote laptop. Installation went fine but on booting, the /bsd kernel, it hangs at acpiprt4. I have tried both 5.0 and current

I have tried using ukc to disable acpi0 which leads to a kernel panic
Code:
panic: no isa bus
I also tried disabling mpbios which still hangs at acpiprt4

I was going to try fiddling with changing acpi0 in ukc but the only configurable values that come up are bus [-1] and flags [0x0]. I do not have the foggiest idea what are reasonable bus numbers or flags to try and did not get much enlightenment with the man pages for acpi.

The phoenix bios itself does not have any acpi configurations options

Is this a lost cause? I can still run Debian Squeeze/Arch on the system but had the sense that was a good time to install current.
Reply With Quote
  #2   (View Single Post)  
Old 13th February 2012
jggimi's Avatar
jggimi jggimi is offline
More noise than signal
 
Join Date: May 2008
Location: USA
Posts: 3,805
Thanked 214 Times in 189 Posts
Default

  1. Did you report this to misc@? I can't recall seeing a recent report quite like this, and you'd have several orders of magnitude more people to help you there. Your problem might be circumventable, or fixable, and the vastly larger audience may be of value.
  2. It appears that your ISA bus is dependent on having ACPI present. If so, I wonder what a dmesg would show from a working kernel -- perhaps a bsd.rd dmesg might be useful, since that should have an ISA bus attachment.
Reply With Quote
  #3   (View Single Post)  
Old 13th February 2012
jggimi's Avatar
jggimi jggimi is offline
More noise than signal
 
Join Date: May 2008
Location: USA
Posts: 3,805
Thanked 214 Times in 189 Posts
Default

Ah, one more thing to try: using "verbose" at the UKC> prompt. You might see something at the hang that provides a useful hint -- there might be a message about something after acpiprt4, for example.
Reply With Quote
  #4   (View Single Post)  
Old 13th February 2012
shep shep is offline
ISO Quartermaster
 
Join Date: May 2008
Location: Dry and Dusty
Posts: 611
Thanked 9 Times in 9 Posts
Default

dmesg:
Code:
OpenBSD 5.1 (RAMDISK_CD) #95: Sun Feb 12 10:02:21 MST 2012
    deraadt@i386.openbsd.org:/usr/src/sys/arch/i386/compile/RAMDISK_CD
cpu0: VIA Esther processor 1500MHz ("CentaurHauls" 686-class) 1.50 GHz
cpu0: FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,CMOV,PAT,CFLUSH,ACPI,MMX,FXSR,SSE,SSE2,TM,SBF,NXE,SSE3,EST,TM2
real mem  = 2078396416 (1982MB)
avail mem = 2037391360 (1943MB)
mainbus0 at root
bios0 at mainbus0: AT/286+ BIOS, date 08/22/07, BIOS32 rev. 0 @ 0xfdd44, SMBIOS rev. 2.4 @ 0x7bee7000 (42 entries)
bios0: vendor FIC version "1.0D-V 08-8A20" date 08/22/2007
bios0: Everex Systems, Inc. Everex StepNote Series
acpi0 at bios0: rev 0
acpi0: sleep states S0 S3 S4 S5
acpi0: tables DSDT FACP SSDT APIC MCFG SLIC
acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat
cpu0 at mainbus0: apid 0 (boot processor)
cpu0: RNG AES AES-CTR SHA1 SHA256 RSA
cpu0: apic clock running at 99MHz
ioapic0 at mainbus0: apid 1 pa 0xfec00000, version 3, 24 pins
ioapic1 at mainbus0: apid 2 pa 0xfecc0000, version 3, 24 pins
acpiprt0 at acpi0: bus 0 (PCI0)
acpiprt1 at acpi0: bus 2 (PEGC)
acpiprt2 at acpi0: bus 3 (PE0C)
acpiprt3 at acpi0: bus 5 (SP2P)
acpiprt4 at acpi0: bus 4 (P2PE)
bios0: ROM list: 0xc0000/0xd800
pci0 at mainbus0 bus 0: configuration mode 1 (bios)
pchb0 at pci0 dev 0 function 0 "VIA P4M900 Host" rev 0x80
pchb1 at pci0 dev 0 function 1 "VIA P4M900 Host" rev 0x00
pchb2 at pci0 dev 0 function 2 "VIA P4M900 Host" rev 0x00
pchb3 at pci0 dev 0 function 3 "VIA P4M900 Host" rev 0x00
pchb4 at pci0 dev 0 function 4 "VIA P4M900 Host" rev 0x00
"VIA P4M900 IOAPIC" rev 0x00 at pci0 dev 0 function 5 not configured
pchb5 at pci0 dev 0 function 6 "VIA P4M900 Security" rev 0x00
pchb6 at pci0 dev 0 function 7 "VIA P4M900 Host" rev 0x00
ppb0 at pci0 dev 1 function 0 "VIA VT8377 AGP" rev 0x00
pci1 at ppb0 bus 1
vga1 at pci1 dev 0 function 0 "VIA Chrome9 HC IGP" rev 0x01
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
ppb1 at pci0 dev 2 function 0 "VIA P4M900 PCI-PCI" rev 0x00: apic 2 int 3
pci2 at ppb1 bus 2
ppb2 at pci0 dev 3 function 0 "VIA P4M900 PCI-PCI" rev 0x80: apic 2 int 7
pci3 at ppb2 bus 3
pciide0 at pci0 dev 15 function 0 "VIA VT8237A SATA" rev 0x80: DMA
pciide0: using apic 1 int 21 for native-PCI interrupt
wd0 at pciide0 channel 0 drive 0: <WDC WD600BEVS-22RST0>
wd0: 16-sector PIO, LBA48, 57231MB, 117210240 sectors
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 6
pciide1 at pci0 dev 15 function 1 "VIA VT82C571 IDE" rev 0x07: DMA, channel 0 configured to compatibility, channel 1 configured to compatibility
pciide1: channel 0 ignored (disabled)
atapiscsi0 at pciide1 channel 1 drive 0
scsibus0 at atapiscsi0: 2 targets
cd0 at scsibus0 targ 0 lun 0: <HL-DT-ST, RW/DVD GCC-T10N, 1.00> ATAPI 5/cdrom removable
cd0(pciide1:1:0): using PIO mode 4, DMA mode 2
uhci0 at pci0 dev 16 function 0 "VIA VT83C572 USB" rev 0xa0: apic 1 int 20
uhci1 at pci0 dev 16 function 1 "VIA VT83C572 USB" rev 0xa0: apic 1 int 22
uhci2 at pci0 dev 16 function 2 "VIA VT83C572 USB" rev 0xa0: apic 1 int 21
uhci3 at pci0 dev 16 function 3 "VIA VT83C572 USB" rev 0xa0: apic 1 int 23
ehci0 at pci0 dev 16 function 4 "VIA VT6202 USB" rev 0x86: apic 1 int 21
ehci0: timed out waiting for BIOS
usb0 at ehci0: USB revision 2.0
uhub0 at usb0 "VIA EHCI root hub" rev 2.00/1.00 addr 1
pcib0 at pci0 dev 17 function 0 "VIA VT8237A ISA" rev 0x00
pchb7 at pci0 dev 17 function 7 "VIA VT8251 VLINK" rev 0x00
vr0 at pci0 dev 18 function 0 "VIA RhineII-2" rev 0x7c: apic 1 int 23, address 00:14:0b:41:a3:ae
ukphy0 at vr0 phy 1: Generic IEEE 802.3u media interface, rev. 10: OUI 0x004063, model 0x0032
ppb3 at pci0 dev 19 function 0 "VIA VT8237A PCI-PCI" rev 0x00
pci4 at ppb3 bus 4
"VIA HD Audio" rev 0x10 at pci4 dev 1 function 0 not configured
ppb4 at pci0 dev 19 function 1 "VIA VT8237A PCI-PCI" rev 0x00
pci5 at ppb4 bus 5
ath0 at pci5 dev 1 function 0 "Atheros AR2413" rev 0x01: apic 1 int 18
ath0: AR2413 7.8 phy 4.5 rf 5.6, FCC2A*, address 00:16:44:9c:83:31
usb1 at uhci0: USB revision 1.0
uhub1 at usb1 "VIA UHCI root hub" rev 1.00/1.00 addr 1
usb2 at uhci1: USB revision 1.0
uhub2 at usb2 "VIA UHCI root hub" rev 1.00/1.00 addr 1
usb3 at uhci2: USB revision 1.0
uhub3 at usb3 "VIA UHCI root hub" rev 1.00/1.00 addr 1
usb4 at uhci3: USB revision 1.0
uhub4 at usb4 "VIA UHCI root hub" rev 1.00/1.00 addr 1
isa0 at pcib0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
softraid0 at root
scsibus1 at softraid0: 256 targets
root on rd0a swap on rd0b dump on rd0b
umass0 at uhub0 port 4 configuration 1 interface 0 "USB DISK 2.0" rev 2.00/12.19 addr 2
umass0: using SCSI over Bulk-Only
scsibus2 at umass0: 2 targets, initiator 0
sd0 at scsibus2 targ 1 lun 0: <USB, DISK 2.0, 1219> SCSI0 0/direct removable serial.090c1000R75JEPN4EPUW
sd0: 956MB, 512 bytes/sector, 1957888 sector

Last edited by shep; 13th February 2012 at 09:04 PM. Reason: paste had 2 dmesgs in buffer
Reply With Quote
  #5   (View Single Post)  
Old 14th February 2012
jggimi's Avatar
jggimi jggimi is offline
More noise than signal
 
Join Date: May 2008
Location: USA
Posts: 3,805
Thanked 214 Times in 189 Posts
Default

ACPI must be a drop dead requirement for that hardware infrastructure, as the chain is
Code:
root -> mainbus0 -> pci0 -> pcib0 -> isa0
Reply With Quote
  #6   (View Single Post)  
Old 14th February 2012
shep shep is offline
ISO Quartermaster
 
Join Date: May 2008
Location: Dry and Dusty
Posts: 611
Thanked 9 Times in 9 Posts
Default

@jggimi
Thanks for the diagram. I think I have some insight regarding the hierarchy/dependencies of the device drivers and will now consider this a lost cause and move on to FreeBSD
Reply With Quote
  #7   (View Single Post)  
Old 14th July 2014
shep shep is offline
ISO Quartermaster
 
Join Date: May 2008
Location: Dry and Dusty
Posts: 611
Thanked 9 Times in 9 Posts
Default OpenBSD i386 buggy acpi tables

Sorry for reviving an old thread but as of July 8, 2014, OpenBSD 5.5current now runs on this gutless wonder.
The bios had a bogus interupt
Quote:
Changes made between OpenBSD 5.5 and -current

If acpi(4) finds a bogus interrupt, don't panic but print a message, to workaround dodgy BIOS.

Last edited by shep; 14th July 2014 at 10:18 PM. Reason: Admin request to change thread title
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
FreeBSD 8.0-CURRENT (amd64 & i386) VMware Virtual Appliances Available glarkin_at_FreeBSD FreeBSD Installation and Upgrading 1 3rd December 2008 08:49 AM
OpenBSD4.4 i386 ACPI ps/2 keyboard shep OpenBSD General 2 16th November 2008 11:50 PM
pf tables how long values stored ijk FreeBSD Security 3 12th August 2008 11:45 AM
PF <tables> hunteronline FreeBSD Security 8 16th July 2008 08:52 PM


All times are GMT. The time now is 04:42 PM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Content copyright © 2007-2010, the authors
Daemon image copyright ©1988, Marshall Kirk McKusick