DaemonForums  

Go Back   DaemonForums > FreeBSD > FreeBSD Ports and Packages

FreeBSD Ports and Packages Installation and upgrading of ports and packages on FreeBSD.

Reply
 
Thread Tools Display Modes
  #1   (View Single Post)  
Old 10th September 2008
daemonFromHeaven daemonFromHeaven is offline
Port Guard
 
Join Date: May 2008
Posts: 31
Thanked 0 Times in 0 Posts
Default fusefs-ntfs problem...

Hi!

I've installed fusefs-ntfs port today and it broke my FreeBSD 7.0 system. First it rebooted my system twice in attempt to install the port and then after I managed to install it and configuring it reading the /usr/local/share/doc/ntfs-3g/README.FreeBSD file and rebooting it could not mount /usr and it falls into single-user mode asking me to run fsck manually and so I did.

fsck prints tons of output asking me [RECONNECT], [CLEAR] some dirs, etc.. Now I'm without my FreeBSD system.

What could be the problem that it cannot mount /usr ?

Thanks!

EDIT1:
I've made a fresh minimal install on my system and after that tried to install the fusefs-ntfs port again and it crashed my system one more time

It printed some output about the crash, but I was not able to write down all of it, but this was the first line of the crash:
Fatal trap 12: page fault while in kernel mode

This was the error or something like that followed by some other lines of output.

Does anyone have experienced something like that?

EDIT2:
I've found this thread:
http://freebsd.monkey.org/freebsd-bu.../msg00550.html

It is supposed to fix the problem after I remove these options from my kernel, but in fact I don't even have these options in my custom kernel...
options DEBUG_LOCKS
options DEBUG_VFS_LOCKS

Problem remains...

Last edited by daemonFromHeaven; 10th September 2008 at 01:36 PM.
Reply With Quote
  #2   (View Single Post)  
Old 10th September 2008
daemonFromHeaven daemonFromHeaven is offline
Port Guard
 
Join Date: May 2008
Posts: 31
Thanked 0 Times in 0 Posts
Default

Any tips?
Reply With Quote
  #3   (View Single Post)  
Old 11th September 2008
robbak's Avatar
robbak robbak is offline
Real Name: Robert Backhaus
VPN Cryptographer
 
Join Date: May 2008
Location: North Queensland, Australia
Posts: 366
Thanked 40 Times in 39 Posts
Default

Firstly, A port will not reboot the system to install the port. The port may ask you to reboot in its pkg-message displayed at the end of an install, but it will not do a reboot. If a system reboots while building a port, you have memory (or other hardware) issues. Page faults in known-good code also point to hardware issues.

Get a copy of memtest-86+ and run it for a few hours. (24 hours is considered a reasonable test!)

Installing the fuse-ntfs port could not damage your system. A kernel panic while attempting to use it could, perhaps; The solution would be start the system in single-user mode (or boot from a live cd) and remove the fuse entry from /boot/loader.conf

But this sounds more like hardware than anything else.
__________________
The only dumb question is a question not asked.
The only dumb answer is an answer not given.
Reply With Quote
  #4   (View Single Post)  
Old 11th September 2008
daemonFromHeaven daemonFromHeaven is offline
Port Guard
 
Join Date: May 2008
Posts: 31
Thanked 0 Times in 0 Posts
Default

Quote:
Originally Posted by robbak
Firstly, A port will not reboot the system to install the port. The port may ask you to reboot in its pkg-message displayed at the end of an install, but it will not do a reboot. If a system reboots while building a port, you have memory (or other hardware) issues. Page faults in known-good code also point to hardware issues.
Yes it did reboot my system, showing some crash report like this fatal trap described here:
http://freebsd.monkey.org/freebsd-bu.../msg00094.html

I read the lists about this problem and should be fix when the kernel options I mentioned are removed, but I as said I don't have these options in my custom kernel.

I think it must be something with the kernel or with the fusefs-ntfs port...

EDIT:
Does anyone of you having a working fusefs-ntfs port compiled it with some extra options and/or have the above kernel options in your kernel config file?

Last edited by daemonFromHeaven; 11th September 2008 at 10:38 AM.
Reply With Quote
  #5   (View Single Post)  
Old 12th September 2008
daemonFromHeaven daemonFromHeaven is offline
Port Guard
 
Join Date: May 2008
Posts: 31
Thanked 0 Times in 0 Posts
Default

Problem solved. I had to run make buildworld and make installworld to update my userland.
Reply With Quote
Reply

Tags
ntfs

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Mounting ntfs drive as rw using fusefs-ntfs caesius FreeBSD General 3 12th October 2008 11:08 AM
fusefs-kmod: requires the userland sources to be installed? zelut FreeBSD Ports and Packages 2 7th October 2008 10:39 PM
Cannot mount (NTFS) IIMarckus OpenBSD General 4 11th August 2008 08:44 PM
mount fusefs (sshfs) from fstab elon FreeBSD General 4 29th July 2008 06:41 PM
Problem updating fusefs-kmod Malakim FreeBSD Ports and Packages 6 25th July 2008 12:40 PM


All times are GMT. The time now is 08:29 AM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Content copyright © 2007-2010, the authors
Daemon image copyright ©1988, Marshall Kirk McKusick