DaemonForums  

Go Back   DaemonForums > OpenBSD > OpenBSD Installation and Upgrading

OpenBSD Installation and Upgrading Installing and upgrading OpenBSD.

 
 
Thread Tools Display Modes
Prev Previous Post   Next Post Next
  #1   (View Single Post)  
Old 13th December 2008
revzalot's Avatar
revzalot revzalot is offline
Shell Scout
 
Join Date: May 2008
Posts: 123
Thanked 1 Time in 1 Post
Default soekris help

Awhile back I bought a soekris off ebay and installed OBSD in a compact flash using bowlfish. I'm getting a ddb error unknown to me. I really hope it's not the box and just the CF.

Code:
comBIOS ver. 1.27  20041122  Copyright (C) 2000-2004 Soekris Engineering.

net45xx

0064 Mbyte Memory                        CPU 80486 133 Mhz 

Pri Mas  LEXAR ATA FLASH                 LBA 993-16-63  500 Mbyte

Slot   Vend Dev  ClassRev Cmd  Stat CL LT HT  Base1    Base2   Int 
-------------------------------------------------------------------
0:00:0 1022 3000 06000000 0006 2280 00 00 00 00000000 00000000 
0:17:0 104C AC51 06070000 0107 0210 10 3F 82 A0000000 020000A0 10
0:17:1 104C AC51 06070000 0107 0210 10 3F 82 A0001000 020000A0 10
0:18:0 100B 0020 02000000 0107 0290 00 3F 00 0000E101 A0002000 11
0:19:0 100B 0020 02000000 0107 0290 00 3F 00 0000E201 A0003000 05

 1 Seconds to automatic boot.   Press Ctrl-P for entering Monitor.
Using drive 0, partition 3.
Loading...
probing: pc0 com0 com1 mem[639K 63M a20=on] 
disk: hd0+
>> OpenBSD/i386 BOOT 3.01
switching console to com0                                                       
>> OpenBSD/i386 BOOT 3.01                                                       
com0: changing speed to 19200 baud in 5 seconds, change your terminal to match! 
                                                                                
com0: 19200 baud                                                                
boot>                                                                           
booting hd0a:/bsd: 1833484+365768 [52+105808+97045]=0x24a8e4                    
entry point at 0x200120                                                         
                                                                                
[ using 203280 bytes of bsd ELF symbol table ]                                  
Copyright (c) 1982, 1986, 1989, 1991, 1993                                      
        The Regents of the University of California.  All rights reserved.      
Copyright (c) 1995-2008 OpenBSD. All rights reserved.  http://www.OpenBSD.org   
                                                                                
OpenBSD 4.3 (NET45xx) #0: Fri Mar 21 12:39:33 PDT 2008                          
    anton@hpv.my.domain:/usr/src/sys/arch/i386/compile/NET45xx                  
cpu0: AMD Am486DX4 W/B or Am5x86 W/B 150 ("AuthenticAMD" 486-class)             
cpu0: FPU                                                                       
real mem  = 66678784 (63MB)                                                     
avail mem = 60432384 (57MB)                                                     
mainbus0 at root                                                                
bios0 at mainbus0: AT/286+ BIOS, date 20/41/22, BIOS32 rev. 0 @ 0xf7840         
pcibios0 at bios0: rev 2.0 @ 0xf0000/0x10000                                    
pcibios0: pcibios_get_intr_routing - function not supported                     
pcibios0: PCI IRQ Routing information unavailable.                              
pcibios0: PCI bus #2 is the last bus                                            
bios0: ROM list: 0xc8000/0x9000                                                 
cpu0 at mainbus0                                                                
pci0 at mainbus0 bus 0: configuration mode 1 (no bios)                          
elansc0 at pci0 dev 0 function 0 "AMD ElanSC520 PCI" rev 0x00: product 0 steppi>
gpio0 at elansc0: 32 pins                                                       
cbb0 at pci0 dev 17 function 0 "TI PCI1420 CardBus" rev 0x00: irq 10            
cbb1 at pci0 dev 17 function 1 "TI PCI1420 CardBus" rev 0x00: irq 10            
sis0 at pci0 dev 18 function 0 "NS DP83815 10/100" rev 0x00, DP83816A: irq 11, 8
nsphyter0 at sis0 phy 0: DP83815 10/100 PHY, rev. 1                             
sis1 at pci0 dev 19 function 0 "NS DP83815 10/100" rev 0x00, DP83816A: irq 5, a9
nsphyter1 at sis1 phy 0: DP83815 10/100 PHY, rev. 1                             
cardslot0 at cbb0 slot 0 flags 0                                                
cardbus0 at cardslot0: bus 1 device 0 cacheline 0x10, lattimer 0x3f             
pcmcia0 at cardslot0                                                            
cardslot1 at cbb1 slot 1 flags 0                                                
cardbus1 at cardslot1: bus 2 device 0 cacheline 0x10, lattimer 0x3f             
pcmcia1 at cardslot1                                                            
isa0 at mainbus0                                                                
isadma0 at isa0                                                                 
wdc0 at isa0 port 0x1f0/8 irq 14                                                
wd0 at wdc0 channel 0 drive 0: <LEXAR ATA FLASH>                                
wd0: 16-sector PIO, LBA, 488MB, 1000944 sectors                                 
wd0(wdc0:0:0): using BIOS timings                                               
npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16                
pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo                       
pccom0: console                                                                 
pccom1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo                       
biomask f7c7 netmask ffe7 ttymask ffe7                                          
root on wd0a swap on wd0b dump on wd0b                                          
filesystem type 8 not known.. assuming ffs                                      
warning: /dev/console error 22                                                  
exec /sbin/init: error 22                                                       
exec /sbin/oinit: error 22                                                      
exec /sbin/init.bak: error 22                                                   
init: not found                                                                 
panic: no init                                                                  
Stopped at      Debugger+0x4:   leave                                           
RUN AT LEAST 'trace' AND 'ps' AND INCLUDE OUTPUT WHEN REPORTING THIS PANIC!     
DO NOT EVEN BOTHER REPORTING THIS WITHOUT INCLUDING THAT INFORMATION!           
ddb>
Reply With Quote
 

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Soekris experiences Carpetsmoker General Hardware 42 21st August 2009 01:52 PM
Soekris Help revzalot General Hardware 2 27th August 2008 01:35 PM


All times are GMT. The time now is 09:34 PM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Content copyright © 2007-2010, the authors
Daemon image copyright ©1988, Marshall Kirk McKusick