DaemonForums  

Go Back   DaemonForums > OpenBSD > OpenBSD Installation and Upgrading

OpenBSD Installation and Upgrading Installing and upgrading OpenBSD.

 
 
Thread Tools Display Modes
Prev Previous Post   Next Post Next
  #1   (View Single Post)  
Old 9th February 2009
Quaxo Quaxo is offline
Port Guard
 
Join Date: Jun 2008
Posts: 29
Thanked 0 Times in 0 Posts
Unhappy My D-Link DFE530TX ethernet adapter isnt found. Help!

Hello

In an older hardware setup (I dont remember the OpenBSD version) I used a D-Link DFE530TX REV-C1 10/100Mb ethernet adapter. It worked just fine and was recognized by OpenBSD as "vr0". But now when I install this adapter into my "new" server (OpenBSD v4.4) its not found. This is what the dmesg.boot looks like...

Code:
OpenBSD 4.4 (GENERIC) #1021: Tue Aug 12 17:16:55 MDT 2008
    deraadt@i386.openbsd.org:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: Intel(R) Celeron(R) CPU 440 @ 2.00GHz ("GenuineIntel" 686-class) 2.01 GHz
cpu0: FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,TM,SBF,SSE3,MWAIT,DS-CPL,TM2,CX16,xTPR
real mem  = 2077782016 (1981MB)
avail mem = 2000572416 (1907MB)
mainbus0 at root
bios0 at mainbus0: AT/286+ BIOS, date 11/07/07, BIOS32 rev. 0 @ 0xfb180, SMBIOS rev. 2.4 @ 0xf0100 (30 entries)
bios0: vendor Award Software International, Inc. version "F3" date 11/07/2007
bios0: Gigabyte Technology Co., Ltd. GA-73PVM-S2H
apm0 at bios0: Power Management spec V1.2 (slowidle)
apm0: AC on, battery charge unknown
acpi at bios0 function 0x0 not configured
pcibios0 at bios0: rev 3.0 @ 0xf0000/0xd7d4
pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xfd700/208 (11 entries)
pcibios0: PCI Exclusive IRQs: 5 10 11
pcibios0: no compatible PCI ICU found
pcibios0: Warning, unable to fix up PCI interrupt routing
pcibios0: PCI bus #4 is the last bus
WARNING: unknown PCI device header 0x40.
WARNING: unknown PCI device header 0x40.
WARNING: unknown PCI device header 0x40.
bios0: ROM list: 0xc0000/0xde00
cpu0 at mainbus0
pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
pchb0 at pci0 dev 0 function 0 vendor "NVIDIA", unknown product 0x07c1 rev 0xa2
"NVIDIA MCP73 Memory" rev 0xa2 at pci0 dev 0 function 1 not configured
"NVIDIA MCP73 Memory" rev 0xa1 at pci0 dev 1 function 0 not configured
"NVIDIA MCP73 Memory" rev 0xa1 at pci0 dev 1 function 1 not configured
"NVIDIA MCP73 Memory" rev 0xa1 at pci0 dev 1 function 2 not configured
"NVIDIA MCP73 Memory" rev 0xa1 at pci0 dev 1 function 3 not configured
"NVIDIA MCP73 Memory" rev 0xa1 at pci0 dev 1 function 4 not configured
"NVIDIA MCP73 Memory" rev 0xa1 at pci0 dev 1 function 5 not configured
"NVIDIA MCP73 Memory" rev 0xa1 at pci0 dev 1 function 6 not configured
"NVIDIA MCP73 Memory" rev 0xa1 at pci0 dev 2 function 0 not configured
pcib0 at pci0 dev 3 function 0 "NVIDIA MCP73 ISA" rev 0xa2
nviic0 at pci0 dev 3 function 1 "NVIDIA MCP73 SMBus" rev 0xa1
iic0 at nviic0
spdmem0 at iic0 addr 0x50: 1GB DDR2 SDRAM non-parity PC2-6400CL5
spdmem1 at iic0 addr 0x51: 1GB DDR2 SDRAM non-parity PC2-6400CL5
iic1 at nviic0
"NVIDIA MCP73 Memory" rev 0xa1 at pci0 dev 3 function 2 not configured
"NVIDIA MCP73 Memory" rev 0xa1 at pci0 dev 3 function 4 not configured
ohci0 at pci0 dev 4 function 0 "NVIDIA MCP73 USB" rev 0xa1: irq 5, version 1.0, legacy support
ehci0 at pci0 dev 4 function 1 "NVIDIA MCP73 USB" rev 0xa1: irq 10
usb0 at ehci0: USB revision 2.0
uhub0 at usb0 "NVIDIA EHCI root hub" rev 2.00/1.00 addr 1
pciide0 at pci0 dev 8 function 0 "NVIDIA MCP73 IDE" rev 0xa1: DMA, channel 0 configured to compatibility, channel 1 configured to compatibility
atapiscsi0 at pciide0 channel 0 drive 0
scsibus0 at atapiscsi0: 2 targets, initiator 7
cd0 at scsibus0 targ 0 lun 0: <TSSTcorp, CDDVDW SH-S202J, SB01> ATAPI 5/cdrom removable
cd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 4
pciide0: channel 1 ignored (disabled)
azalia0 at pci0 dev 9 function 0 "NVIDIA MCP73 HD Audio" rev 0xa1: irq 5
azalia0: /usr/src/sys/dev/pci/azalia.c/1348 invalid PCM format: 0x00000000
azalia0: codec[s]: Realtek/0x0885, NVIDIA/0x8001, using Realtek/0x0885
audio0 at azalia0
ppb0 at pci0 dev 10 function 0 "NVIDIA MCP73 PCIE" rev 0xa1
pci1 at ppb0 bus 1
ral0 at pci1 dev 5 function 0 "Ralink RT2561S" rev 0x00: irq 11, address 00:22:6b:a0:fb:19
ral0: MAC/BBP RT2561C, RF RT2527
"TI TSB43AB23 FireWire" rev 0x00 at pci1 dev 7 function 0 not configured
ppb1 at pci0 dev 11 function 0 "NVIDIA MCP73 PCIE" rev 0xa1
pci2 at ppb1 bus 2
ppb2 at pci0 dev 12 function 0 "NVIDIA MCP73 PCIE" rev 0xa1
pci3 at ppb2 bus 3
ppb3 at pci0 dev 13 function 0 "NVIDIA MCP73 PCIE" rev 0xa1
pci4 at ppb3 bus 4
pciide1 at pci0 dev 14 function 0 "NVIDIA MCP73 AHCI" rev 0xa2: DMA (unsupported), channel 0 wired to native-PCI, channel 1 wired to native-PCI
pciide1: using irq 11 for native-PCI interrupt
wd0 at pciide1 channel 0 drive 0: <ST3500320NS>
wd0: 16-sector PIO, LBA48, 476938MB, 976771055 sectors
wd1 at pciide1 channel 0 drive 1: <ST3500320NS>
wd1: 16-sector PIO, LBA48, 476940MB, 976773168 sectors
pciide1: channel 1 ignored (not responding; disabled or no drives?)
nfe0 at pci0 dev 15 function 0 "NVIDIA MCP73 LAN" rev 0xa2: irq 15, address 00:1a:4d:56:2d:8c
rgephy0 at nfe0 phy 1: RTL8169S/8110S PHY, rev. 2
vga1 at pci0 dev 16 function 0 vendor "NVIDIA", unknown product 0x07e1 rev 0xa2
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
drm at vga1 unsupported
isa0 at pcib0
isadma0 at isa0
com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
spkr0 at pcppi0
lpt0 at isa0 port 0x378/4 irq 7
it0 at isa0 port 0x2e/2: IT8718F rev 0x04, EC port 0x290
npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
usb1 at ohci0: USB revision 1.0
uhub1 at usb1 "NVIDIA OHCI root hub" rev 1.00/1.00 addr 1
biomask 7f6d netmask ff6d ttymask ffff
mtrr: Pentium Pro MTRR support
softraid0 at root
root on wd0a swap on wd0b dump on wd0b
I figure "WARNING: unknown PCI device header 0x40." is the problem. But I dont understand why it worked before and not now. I have checked the BIOS but I didnt found any odd settings there.

I also added acpid_flags="" to rc.conf.local but that didnt help (I dont know what "acpi at bios0 function 0x0 not configured" in dmesg.boot really means though; ACPI is enabled as much as possible in BIOS).

Anyone who got an idea of how to fix this?

If you find more things (from reading the dmesg.boot above) that I can fix easy, any help is welcome


Thanks in advance
/Quaxo
Reply With Quote
 

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
D-link (DI-524) router c0mrade General software and network 3 26th January 2009 08:14 AM
Nvidia nForce MCP77 network adapter issue padmanabh FreeBSD Installation and Upgrading 5 17th January 2009 12:18 PM
kde .desktop file link doesn't act like a link when opening files caesius FreeBSD Ports and Packages 3 14th October 2008 07:35 AM
USB wireless network adapter, ndis problem ronaldmcdonald9 FreeBSD General 5 9th July 2008 07:50 AM
Usb serial adapter Business_woman FreeBSD General 10 4th June 2008 03:06 PM


All times are GMT. The time now is 03:52 AM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Content copyright © 2007-2010, the authors
Daemon image copyright ©1988, Marshall Kirk McKusick