DaemonForums  

Go Back   DaemonForums > OpenBSD > OpenBSD General

OpenBSD General Other questions regarding OpenBSD which do not fit in any of the categories below.

Reply
 
Thread Tools Display Modes
  #1   (View Single Post)  
Old 21st September 2011
sepuku's Avatar
sepuku sepuku is offline
Real Name: Vizard Sepuku
Package Pilot
 
Join Date: Jun 2011
Location: Athens & Chania,Greece
Posts: 143
Thanked 0 Times in 0 Posts
Default Keyboard layout lost after upgrade to -current

Hello people,it's been a while and after a lot of testing and experimenting with OpenBSD i decided to "move" to -currnet.

Today i upgraded from -stable to -current following this post:

http://www.daemonforums.org/private....owpm&pmid=7209

Everything works fine so far,but after upgrading i don't have the second layout.(I have the us and the Greek layout.)

Is there a setting i must do after upgrading to have again the Second Layout?


Edit: The sysmerge command was changed accordingly to the OpenBSD 5 -cuurrent that i wanted to move so it was like:

Code:
sysmerge -s ftp://ftp.cc.uoc.gr/mirrors/OpenBSD/snapshots/i386/etc50.tgz -x ftp://ftp.cc.uoc.gr/mirrors/OpenBSD/snapshots/i386//xetc50.tgz

Last edited by sepuku; 21st September 2011 at 11:52 PM.
Reply With Quote
  #2   (View Single Post)  
Old 21st September 2011
jggimi's Avatar
jggimi jggimi is offline
More noise than signal
 
Join Date: May 2008
Location: USA
Posts: 3,608
Thanked 214 Times in 189 Posts
Default

If you review the Following -current FAQ, you will find this entry from 2 June, 2011.
Reply With Quote
  #3   (View Single Post)  
Old 22nd September 2011
sepuku's Avatar
sepuku sepuku is offline
Real Name: Vizard Sepuku
Package Pilot
 
Join Date: Jun 2011
Location: Athens & Chania,Greece
Posts: 143
Thanked 0 Times in 0 Posts
Default

Hello jggimi,

The entry you posted leads to this guide:

http://www.x.org/releases/X11R7.6/do...html#id2548546


So far I gave:
Code:
rm -rf /etc/X11/xkb
And now i have some additional questions:

Is :

Code:
Section "InputClass"
    Identifier "keyboard defaults"
    MatchIsKeyboard "on"

    Option "XkbModel" "pc104"
    Option "XkbLayout" "us,gr"
    Option "XKbOptions" "grp:ctrl_alt_toggle"
EndSection
the only code i need to have a correctly working pc?Do i need to make any symbolic linking like i did in -stable according to this post?:

http://www.daemonforums.org/showthread.php?t=6127

Also i'm wondering what to put in 'XkbModel'.

My dmesg is this:

Code:
$ dmesg
 at mainbus0: apid 1 (application processor)
cpu1: Intel(R) Core(TM)2 Quad CPU Q6600 @ 2.40GHz ("GenuineIntel" 686-class)1 GHz
cpu1: FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE3LUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,SBF,SSE3,MWAIT,DS-CPL,VMX,EST,TM2,S,CX16,xTPR,PDCM
cpu2 at mainbus0: apid 2 (application processor)
cpu2: Intel(R) Core(TM)2 Quad CPU Q6600 @ 2.40GHz ("GenuineIntel" 686-class)1 GHz
cpu2: FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE3LUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,SBF,SSE3,MWAIT,DS-CPL,VMX,EST,TM2,S,CX16,xTPR,PDCM
cpu3 at mainbus0: apid 3 (application processor)
cpu3: Intel(R) Core(TM)2 Quad CPU Q6600 @ 2.40GHz ("GenuineIntel" 686-cla1 GHz
cpu3: FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,SBF,SSE3,MWAIT,DS-CPL,VMX,EST,TM,CX16,xTPR,PDCM
ioapic0 at mainbus0: apid 4 pa 0xfec00000, version 20, 24 pins
acpimcfg0 at acpi0 addr 0xe0000000, bus 0-255
acpihpet0 at acpi0: 14318179 Hz
acpiprt0 at acpi0: bus 0 (PCI0)
acpiprt1 at acpi0: bus 1 (P0P2)
acpiprt2 at acpi0: bus 5 (P0P1)
acpiprt3 at acpi0: bus -1 (P0P5)
acpiprt4 at acpi0: bus -1 (P0P6)
acpiprt5 at acpi0: bus -1 (P0P7)
acpiprt6 at acpi0: bus 3 (P0P8)
acpiprt7 at acpi0: bus 2 (P0P9)
acpiprt8 at acpi0: bus 4 (P0P4)
acpicpu0 at acpi0: PSS
acpicpu1 at acpi0: PSS
acpicpu2 at acpi0: PSS
acpicpu3 at acpi0: PSS
aibs0 at acpi0: RTMP RVLT RFAN GGRP GITM SITM
acpibtn0 at acpi0: PWRB
bios0: ROM list: 0xc0000/0xcc00 0xcd000/0x3000!
cpu0: Enhanced SpeedStep 2406 MHz: speeds: 2394, 1596 MHz
pci0 at mainbus0 bus 0: configuration mode 1 (bios)
pchb0 at pci0 dev 0 function 0 "Intel 82G33 Host" rev 0x02
ppb0 at pci0 dev 1 function 0 "Intel 82G33 PCIE" rev 0x02: apic 4 int 16
pci1 at ppb0 bus 1
vga1 at pci1 dev 0 function 0 "NVIDIA GeForce 8500 GT" rev 0xa1
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
uhci0 at pci0 dev 26 function 0 "Intel 82801I USB" rev 0x02: apic 4 int 16
uhci1 at pci0 dev 26 function 1 "Intel 82801I USB" rev 0x02: apic 4 int 21
uhci2 at pci0 dev 26 function 2 "Intel 82801I USB" rev 0x02: apic 4 int 18
ehci0 at pci0 dev 26 function 7 "Intel 82801I USB" rev 0x02: apic 4 int 18
usb0 at ehci0: USB revision 2.0
uhub0 at usb0 "Intel EHCI root hub" rev 2.00/1.00 addr 1
azalia0 at pci0 dev 27 function 0 "Intel 82801I HD Audio" rev 0x02: msi
azalia0: codecs: Realtek ALC883
audio0 at azalia0
ppb1 at pci0 dev 28 function 0 "Intel 82801I PCIE" rev 0x02: apic 4 int 17
pci2 at ppb1 bus 4
ppb2 at pci0 dev 28 function 4 "Intel 82801I PCIE" rev 0x02: apic 4 int 17
pci3 at ppb2 bus 3
jmb0 at pci3 dev 0 function 0 "JMicron JMB363 IDE/SATA" rev 0x03
ahci0 at jmb0: apic 4 int 16, AHCI 1.0
scsibus0 at ahci0: 32 targets
pciide0 at jmb0: DMA, channel 0 wired to native-PCI, channel 1 wired to natiCI
pciide0: using apic 4 int 16 for native-PCI interrupt
atapiscsi0 at pciide0 channel 0 drive 0
scsibus1 at atapiscsi0: 2 targets
cd0 at scsibus1 targ 0 lun 0: <Optiarc, DVD RW AD-7203A, 1.01> ATAPI 5/cdromovable
atapiscsi1 at pciide0 channel 0 drive 1
scsibus2 at atapiscsi1: 2 targets
cd1 at scsibus2 targ 0 lun 0: <HL-DT-ST, DVD-ROM GDR-H30N, 1.00> ATAPI 5/cdremovable
cd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 4
cd1(pciide0:0:1): using PIO mode 4, Ultra-DMA mode 2
pciide0: channel 1 disabled (no drives)
ppb3 at pci0 dev 28 function 5 "Intel 82801I PCIE" rev 0x02: apic 4 int 16
pci4 at ppb3 bus 2
age0 at pci4 dev 0 function 0 "Attansic Technology L1" rev 0xb0: msi, addres:1d:60:cb:09:62
atphy0 at age0 phy 0: F1 10/100/1000 PHY, rev. 5
uhci3 at pci0 dev 29 function 0 "Intel 82801I USB" rev 0x02: apic 4 int 23
uhci4 at pci0 dev 29 function 1 "Intel 82801I USB" rev 0x02: apic 4 int 19
uhci5 at pci0 dev 29 function 2 "Intel 82801I USB" rev 0x02: apic 4 int 18
ehci1 at pci0 dev 29 function 7 "Intel 82801I USB" rev 0x02: apic 4 int 23
usb1 at ehci1: USB revision 2.0
uhub1 at usb1 "Intel EHCI root hub" rev 2.00/1.00 addr 1
ppb4 at pci0 dev 30 function 0 "Intel 82801BA Hub-to-PCI" rev 0x92
pci5 at ppb4 bus 5
"VIA VT6306 FireWire" rev 0xc0 at pci5 dev 3 function 0 not configured
ichpcib0 at pci0 dev 31 function 0 "Intel 82801IB LPC" rev 0x02: PM disabled
pciide1 at pci0 dev 31 function 2 "Intel 82801I SATA" rev 0x02: DMA, channelonfigured to native-PCI, channel 1 configured to native-PCI
pciide1: using apic 4 int 22 for native-PCI interrupt
wd0 at pciide1 channel 0 drive 0: <ST3250410AS>
wd0: 16-sector PIO, LBA48, 238475MB, 488397168 sectors
wd0(pciide1:0:0): using PIO mode 4, Ultra-DMA mode 6
wd1 at pciide1 channel 1 drive 0: <ST3250410AS>
wd1: 16-sector PIO, LBA48, 238475MB, 488397168 sectors
wd1(pciide1:1:0): using PIO mode 4, Ultra-DMA mode 6
ichiic0 at pci0 dev 31 function 3 "Intel 82801I SMBus" rev 0x02: apic 4 int 
iic0 at ichiic0
spdmem0 at iic0 addr 0x50: 1GB DDR2 SDRAM non-parity PC2-5300CL5
spdmem1 at iic0 addr 0x52: 2GB DDR2 SDRAM non-parity PC2-6400CL5
pciide2 at pci0 dev 31 function 5 "Intel 82801I SATA" rev 0x02: DMA, channelired to native-PCI, channel 1 wired to native-PCI
pciide2: using apic 4 int 22 for native-PCI interrupt
usb2 at uhci0: USB revision 1.0
uhub2 at usb2 "Intel UHCI root hub" rev 1.00/1.00 addr 1
usb3 at uhci1: USB revision 1.0
uhub3 at usb3 "Intel UHCI root hub" rev 1.00/1.00 addr 1
usb4 at uhci2: USB revision 1.0
uhub4 at usb4 "Intel UHCI root hub" rev 1.00/1.00 addr 1
usb5 at uhci3: USB revision 1.0
uhub5 at usb5 "Intel UHCI root hub" rev 1.00/1.00 addr 1
usb6 at uhci4: USB revision 1.0
uhub6 at usb6 "Intel UHCI root hub" rev 1.00/1.00 addr 1
usb7 at uhci5: USB revision 1.0
uhub7 at usb7 "Intel UHCI root hub" rev 1.00/1.00 addr 1
isa0 at ichpcib0
isadma0 at isa0
com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pcppi0 at isa0 port 0x61
spkr0 at pcppi0
wbsio0 at isa0 port 0x2e/2: W83627DHG rev 0x23
lm1 at wbsio0 port 0x290/8: W83627DHG
npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
fd0 at fdc0 drive 0: 1.44MB 80 cyl, 2 head, 18 sec
mtrr: Pentium Pro MTRR support
umass0 at uhub0 port 4 configuration 1 interface 0 "Western Digital My Book" 2.00/1.65 addr 2
umass0: using SCSI over Bulk-Only
scsibus3 at umass0: 2 targets, initiator 0
sd0 at scsibus3 targ 1 lun 0: <WD, 7500AAC External, 1.65> SCSI2 0/direct fiserial.10581100303231343039
sd0: 715404MB, 512 bytes/sector, 1465149168 sectors
uhidev0 at uhub4 port 1 configuration 1 interface 0 "Plus More Enterprise LTSB-compliant keyboard" rev 1.10/1.00 addr 2
uhidev0: iclass 3/1
ukbd0 at uhidev0: 8 modifier keys, 6 key codes
wskbd1 at ukbd0 mux 1
wskbd1: connecting to wsdisplay0
uhidev1 at uhub4 port 1 configuration 1 interface 1 "Plus More Enterprise LTSB-compliant keyboard" rev 1.10/1.00 addr 2
uhidev1: iclass 3/1, 3 report ids
uhid0 at uhidev1 reportid 1: input=2, output=0, feature=0
uhid1 at uhidev1 reportid 2: input=1, output=0, feature=0
ums0 at uhidev1 reportid 3: 0 button, Z dir
wsmouse0 at ums0 mux 0
uhidev2 at uhub4 port 2 configuration 1 interface 0 "Microsoft Microsoft 3-Bn Mouse with IntelliEye(TM)" rev 1.10/3.00 addr 3
uhidev2: iclass 3/1
ums1 at uhidev2: 3 buttons, Z dir
wsmouse1 at ums1 mux 0
vscsi0 at root
scsibus4 at vscsi0: 256 targets
softraid0 at root
scsibus5 at softraid0: 256 targets
root on wd0a (49d84e9ba0acc96a.a) swap on wd0b dump on wd0b
syncing disks... 
OpenBSD 5.0-current (GENERIC.MP) #67: Tue Sep 13 22:12:54 MDT 2011
    deraadt@i386.openbsd.org:/usr/src/sys/arch/i386/compile/GENERIC.MP
cpu0: Intel(R) Core(TM)2 Quad CPU Q6600 @ 2.40GHz ("GenuineIntel" 686-class)1 GHz
cpu0: FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE3LUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,SBF,SSE3,MWAIT,DS-CPL,VMX,EST,TM2,S,CX16,xTPR,PDCM
real mem  = 3220238336 (3071MB)
avail mem = 3157487616 (3011MB)
mainbus0 at root
bios0 at mainbus0: AT/286+ BIOS, date 07/03/07, BIOS32 rev. 0 @ 0xf0010, SMBrev. 2.4 @ 0xf06e0 (71 entries)
bios0: vendor American Megatrends Inc. version "0603" date 07/03/2007
bios0: ASUSTeK Computer INC. P5K
acpi0 at bios0: rev 0
acpi0: sleep states S0 S1 S3 S4 S5
acpi0: tables DSDT FACP APIC MCFG OEMB HPET OSFR
acpi0: wakeup devices P0P2(S4) P0P1(S4) UAR1(S4) PS2K(S4) EUSB(S4) USBE(S4) (S4) P0P6(S4) P0P7(S4) P0P8(S4) P0P9(S4) USB0(S4) USB1(S4) USB2(S4) USB3(S4)4(S4) USB5(S4) USB6(S4) P0P4(S4)
acpitimer0 at acpi0: 3579545 Hz, 24 bits
acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat
cpu0 at mainbus0: apid 0 (boot processor)
cpu0: apic clock running at 267MHz
cpu1 at mainbus0: apid 1 (application processor)
cpu1: Intel(R) Core(TM)2 Quad CPU Q6600 @ 2.40GHz ("GenuineIntel" 686-class)1 GHz
cpu1: FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE3LUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,SBF,SSE3,MWAIT,DS-CPL,VMX,EST,TM2,S,CX16,xTPR,PDCM
cpu2 at mainbus0: apid 2 (application processor)
cpu2: Intel(R) Core(TM)2 Quad CPU Q6600 @ 2.40GHz ("GenuineIntel" 686-class)1 GHz
cpu2: FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE3LUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,SBF,SSE3,MWAIT,DS-CPL,VMX,EST,TM2,S,CX16,xTPR,PDCM
cpu3 at mainbus0: apid 3 (application processor)
cpu3: Intel(R) Core(TM)2 Quad CPU Q6600 @ 2.40GHz ("GenuineIntel" 686-class)1 GHz
cpu3: FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE3LUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,SBF,SSE3,MWAIT,DS-CPL,VMX,EST,TM2,S,CX16,xTPR,PDCM
ioapic0 at mainbus0: apid 4 pa 0xfec00000, version 20, 24 pins
acpimcfg0 at acpi0 addr 0xe0000000, bus 0-255
acpihpet0 at acpi0: 14318179 Hz
acpiprt0 at acpi0: bus 0 (PCI0)
acpiprt1 at acpi0: bus 1 (P0P2)
acpiprt2 at acpi0: bus 5 (P0P1)
acpiprt3 at acpi0: bus -1 (P0P5)
acpiprt4 at acpi0: bus -1 (P0P6)
acpiprt5 at acpi0: bus -1 (P0P7)
acpiprt6 at acpi0: bus 3 (P0P8)
acpiprt7 at acpi0: bus 2 (P0P9)
acpiprt8 at acpi0: bus 4 (P0P4)
acpicpu0 at acpi0: PSS
acpicpu1 at acpi0: PSS
acpicpu2 at acpi0: PSS
acpicpu3 at acpi0: PSS
aibs0 at acpi0: RTMP RVLT RFAN GGRP GITM SITM
acpibtn0 at acpi0: PWRB
bios0: ROM list: 0xc0000/0xcc00 0xcd000/0x3000!
cpu0: Enhanced SpeedStep 2406 MHz: speeds: 2394, 1596 MHz
pci0 at mainbus0 bus 0: configuration mode 1 (bios)
pchb0 at pci0 dev 0 function 0 "Intel 82G33 Host" rev 0x02
ppb0 at pci0 dev 1 function 0 "Intel 82G33 PCIE" rev 0x02: apic 4 int 16
pci1 at ppb0 bus 1
vga1 at pci1 dev 0 function 0 "NVIDIA GeForce 8500 GT" rev 0xa1
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
uhci0 at pci0 dev 26 function 0 "Intel 82801I USB" rev 0x02: apic 4 int 16
uhci1 at pci0 dev 26 function 1 "Intel 82801I USB" rev 0x02: apic 4 int 21
uhci2 at pci0 dev 26 function 2 "Intel 82801I USB" rev 0x02: apic 4 int 18
ehci0 at pci0 dev 26 function 7 "Intel 82801I USB" rev 0x02: apic 4 int 18
usb0 at ehci0: USB revision 2.0
uhub0 at usb0 "Intel EHCI root hub" rev 2.00/1.00 addr 1
azalia0 at pci0 dev 27 function 0 "Intel 82801I HD Audio" rev 0x02: msi
azalia0: codecs: Realtek ALC883
audio0 at azalia0
ppb1 at pci0 dev 28 function 0 "Intel 82801I PCIE" rev 0x02: apic 4 int 17
pci2 at ppb1 bus 4
ppb2 at pci0 dev 28 function 4 "Intel 82801I PCIE" rev 0x02: apic 4 int 17
pci3 at ppb2 bus 3
jmb0 at pci3 dev 0 function 0 "JMicron JMB363 IDE/SATA" rev 0x03
ahci0 at jmb0: apic 4 int 16, AHCI 1.0
scsibus0 at ahci0: 32 targets
pciide0 at jmb0: DMA, channel 0 wired to native-PCI, channel 1 wired to natiCI
pciide0: using apic 4 int 16 for native-PCI interrupt
atapiscsi0 at pciide0 channel 0 drive 0
scsibus1 at atapiscsi0: 2 targets
cd0 at scsibus1 targ 0 lun 0: <Optiarc, DVD RW AD-7203A, 1.01> ATAPI 5/cdromovable
atapiscsi1 at pciide0 channel 0 drive 1
scsibus2 at atapiscsi1: 2 targets
cd1 at scsibus2 targ 0 lun 0: <HL-DT-ST, DVD-ROM GDR-H30N, 1.00> ATAPI 5/cdremovable
cd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 4
cd1(pciide0:0:1): using PIO mode 4, Ultra-DMA mode 2
pciide0: channel 1 disabled (no drives)
ppb3 at pci0 dev 28 function 5 "Intel 82801I PCIE" rev 0x02: apic 4 int 16
pci4 at ppb3 bus 2
age0 at pci4 dev 0 function 0 "Attansic Technology L1" rev 0xb0: msi, addres:1d:60:cb:09:62
atphy0 at age0 phy 0: F1 10/100/1000 PHY, rev. 5
uhci3 at pci0 dev 29 function 0 "Intel 82801I USB" rev 0x02: apic 4 int 23
uhci4 at pci0 dev 29 function 1 "Intel 82801I USB" rev 0x02: apic 4 int 19
uhci5 at pci0 dev 29 function 2 "Intel 82801I USB" rev 0x02: apic 4 int 18
ehci1 at pci0 dev 29 function 7 "Intel 82801I USB" rev 0x02: apic 4 int 23
usb1 at ehci1: USB revision 2.0
uhub1 at usb1 "Intel EHCI root hub" rev 2.00/1.00 addr 1
ppb4 at pci0 dev 30 function 0 "Intel 82801BA Hub-to-PCI" rev 0x92
pci5 at ppb4 bus 5
"VIA VT6306 FireWire" rev 0xc0 at pci5 dev 3 function 0 not configured
ichpcib0 at pci0 dev 31 function 0 "Intel 82801IB LPC" rev 0x02: PM disabled
pciide1 at pci0 dev 31 function 2 "Intel 82801I SATA" rev 0x02: DMA, channelonfigured to native-PCI, channel 1 configured to native-PCI
pciide1: using apic 4 int 22 for native-PCI interrupt
wd0 at pciide1 channel 0 drive 0: <ST3250410AS>
wd0: 16-sector PIO, LBA48, 238475MB, 488397168 sectors
wd0(pciide1:0:0): using PIO mode 4, Ultra-DMA mode 6
wd1 at pciide1 channel 1 drive 0: <ST3250410AS>
wd1: 16-sector PIO, LBA48, 238475MB, 488397168 sectors
wd1(pciide1:1:0): using PIO mode 4, Ultra-DMA mode 6
ichiic0 at pci0 dev 31 function 3 "Intel 82801I SMBus" rev 0x02: apic 4 int 
iic0 at ichiic0
spdmem0 at iic0 addr 0x50: 1GB DDR2 SDRAM non-parity PC2-5300CL5
spdmem1 at iic0 addr 0x52: 2GB DDR2 SDRAM non-parity PC2-6400CL5
pciide2 at pci0 dev 31 function 5 "Intel 82801I SATA" rev 0x02: DMA, channelired to native-PCI, channel 1 wired to native-PCI
pciide2: using apic 4 int 22 for native-PCI interrupt
usb2 at uhci0: USB revision 1.0
uhub2 at usb2 "Intel UHCI root hub" rev 1.00/1.00 addr 1
usb3 at uhci1: USB revision 1.0
uhub3 at usb3 "Intel UHCI root hub" rev 1.00/1.00 addr 1
usb4 at uhci2: USB revision 1.0
uhub4 at usb4 "Intel UHCI root hub" rev 1.00/1.00 addr 1
usb5 at uhci3: USB revision 1.0
uhub5 at usb5 "Intel UHCI root hub" rev 1.00/1.00 addr 1
usb6 at uhci4: USB revision 1.0
uhub6 at usb6 "Intel UHCI root hub" rev 1.00/1.00 addr 1
usb7 at uhci5: USB revision 1.0
uhub7 at usb7 "Intel UHCI root hub" rev 1.00/1.00 addr 1
isa0 at ichpcib0
isadma0 at isa0
com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pcppi0 at isa0 port 0x61
spkr0 at pcppi0
wbsio0 at isa0 port 0x2e/2: W83627DHG rev 0x23
lm1 at wbsio0 port 0x290/8: W83627DHG
npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
fd0 at fdc0 drive 0: 1.44MB 80 cyl, 2 head, 18 sec
mtrr: Pentium Pro MTRR support
umass0 at uhub0 port 4 configuration 1 interface 0 "Western Digital My Book" 2.00/1.65 addr 2
umass0: using SCSI over Bulk-Only
scsibus3 at umass0: 2 targets, initiator 0
sd0 at scsibus3 targ 1 lun 0: <WD, 7500AAC External, 1.65> SCSI2 0/direct fiserial.10581100303231343039
sd0: 715404MB, 512 bytes/sector, 1465149168 sectors
uhidev0 at uhub4 port 1 configuration 1 interface 0 "Plus More Enterprise LTSB-compliant keyboard" rev 1.10/1.00 addr 2
uhidev0: iclass 3/1
ukbd0 at uhidev0: 8 modifier keys, 6 key codes
wskbd1 at ukbd0 mux 1
wskbd1: connecting to wsdisplay0
uhidev1 at uhub4 port 1 configuration 1 interface 1 "Plus More Enterprise LTSB-compliant keyboard" rev 1.10/1.00 addr 2
uhidev1: iclass 3/1, 3 report ids
uhid0 at uhidev1 reportid 1: input=2, output=0, feature=0
uhid1 at uhidev1 reportid 2: input=1, output=0, feature=0
ums0 at uhidev1 reportid 3: 0 button, Z dir
wsmouse0 at ums0 mux 0
uhidev2 at uhub4 port 2 configuration 1 interface 0 "Microsoft Microsoft 3-Bn Mouse with IntelliEye(TM)" rev 1.10/3.00 addr 3
uhidev2: iclass 3/1
ums1 at uhidev2: 3 buttons, Z dir
wsmouse1 at ums1 mux 0
vscsi0 at root
scsibus4 at vscsi0: 256 targets
softraid0 at root
scsibus5 at softraid0: 256 targets
root on wd0a (49d84e9ba0acc96a.a) swap on wd0b dump on wd0b


I think it shouldbe 'pckbc' but i'm not sure and i'm afraid i will lose system stability if i do random things and that's why i'm asking.

If you want me to provide any additional info please let me know,

Thanx in advance.
Reply With Quote
  #4   (View Single Post)  
Old 22nd September 2011
jggimi's Avatar
jggimi jggimi is offline
More noise than signal
 
Join Date: May 2008
Location: USA
Posts: 3,608
Thanked 214 Times in 189 Posts
Default

I've never used any of the kbd configuration tools with X11 -- as a mono-linguist from the U.S., I've always used the defaults.

Your available configuration options are laid out in /usr/X11R6/share/X11/xkb. If it were me, I would use setxkbmap(1) and determine my proper settings before mucking about in an xorg.conf file.
Reply With Quote
  #5   (View Single Post)  
Old 22nd September 2011
sepuku's Avatar
sepuku sepuku is offline
Real Name: Vizard Sepuku
Package Pilot
 
Join Date: Jun 2011
Location: Athens & Chania,Greece
Posts: 143
Thanked 0 Times in 0 Posts
Default

Quote:
Originally Posted by jggimi View Post
If it were me, I would use setxkbmap(1) and determine my proper settings before mucking about in an xorg.conf file.
And you would determine that *only* by using the setxkbmap man page?Cause so far i can't find anything relative with the things i asked.


If not a shame,sure it's a pity that there is NO clear guidance from OpenBSD people on how to add layouts.In every section of the FAQ they go so deep and add every detail that i can't stop wondering why not include something like that...even for a -current it's important to at least have some basic things...

Just upgrade and there you go...You don't even have the ability to write on your language.
Reply With Quote
  #6   (View Single Post)  
Old 22nd September 2011
ocicat ocicat is offline
Administrator
 
Join Date: Apr 2008
Posts: 2,873
Thanked 190 Times in 160 Posts
Default

Quote:
Originally Posted by sepuku View Post
If not a shame,sure it's a pity that there is NO clear guidance from OpenBSD people on how to add layouts.In every section of the FAQ they go so deep and add every detail that i can't stop wondering why not include something like that...
Internationalization (i18n) has tradtionally been a weak point with OpenBSD for a very long time. Most of the regulars here (including me...) are English-centric, so we haven't had to deal with configuration.
  • Asking for assistance on the official misc@ may be in order. However, do consider summarizing what homework has been done in the past to solve the problem when posting. This will at least show that you have put effort into finding a solution yourself. Posts then show no prior study are frequently ignored.
  • If you do post to misc@, do not ask that material be added to the FAQ. While I understand where you are coming from, the developers & technical writers see such requests as a feature request. Feature requests are not warmly received. Ever.
  • If you do chase this matter down to completion, consider writing a FAQ addendum yourself. Submit this to misc@ as a diff(1) format. Changes submitted with the work needed to implement them have a much higher chance of being accepted & integrated.
While someone here might pipe up with a suggestion, experience points that most here are English-centric or tolerate the English language default.

Good luck in your search.
Reply With Quote
  #7   (View Single Post)  
Old 22nd September 2011
sepuku's Avatar
sepuku sepuku is offline
Real Name: Vizard Sepuku
Package Pilot
 
Join Date: Jun 2011
Location: Athens & Chania,Greece
Posts: 143
Thanked 0 Times in 0 Posts
Default

Quote:
Originally Posted by ocicat View Post
[*] If you do chase this matter down to completion, consider writing a FAQ addendum yourself.
Hello ocicat,


I don't think that my experience and OpenBSD knowledge so far is enough to to write an addendum even if i finally manage to make it work.Yet this is a later thought.So i 'll concentrate to finding a solution for now.
Reply With Quote
  #8   (View Single Post)  
Old 22nd September 2011
sepuku's Avatar
sepuku sepuku is offline
Real Name: Vizard Sepuku
Package Pilot
 
Join Date: Jun 2011
Location: Athens & Chania,Greece
Posts: 143
Thanked 0 Times in 0 Posts
Default

Fixed.Just in case someone deals with the same problem that's what i did. :
According to:

http://www.openbsd.org/faq/current.html#20110602


1)
Code:
rm -rf /etc/X11/xkb
2)
Code:
rm /etc/X11/xorg.conf
Then created a file as shown here: http://www.x.org/releases/X11R7.6/do...html#id2548546

3)
Code:
vi /etc/X11/xorg.conf.d/90-default-kbd.conf
and added these lines:

Code:
Section "InputClass"
    Identifier "keyboard defaults"
    MatchIsKeyboard "on"
 
    Option "XkbModel" "pc105"
    Option "XkbLayout" "us,gr"
    Option "XKbOptions" "grp:ctrl_alt_toggle,terminate:ctrl_alt_bksp"
EndSection

Reboot and that's all.

Also before i set the file i was able to have both layouts using this command:

Code:
setxkbmap -model pc105 -layout "us,gr" -option "grp:ctrl_alt_toggle"
Reply With Quote
  #9   (View Single Post)  
Old 22nd September 2011
jggimi's Avatar
jggimi jggimi is offline
More noise than signal
 
Join Date: May 2008
Location: USA
Posts: 3,608
Thanked 214 Times in 189 Posts
Default

Excellent!!

I'm so glad you got it working, and that you described how you did it so clearly!
Reply With Quote
Old 22nd September 2011
BSDfan666 BSDfan666 is offline
Real Name: N/A, this is the interweb.
Helpful companion
 
Join Date: Apr 2008
Location: Ontario, Canada
Posts: 2,223
Thanked 193 Times in 184 Posts
Default

I don't believe OpenBSD's Xenocara has xorg.conf.d yet, so that part is unnecessary AFAIK.
Reply With Quote
Old 22nd September 2011
sepuku's Avatar
sepuku sepuku is offline
Real Name: Vizard Sepuku
Package Pilot
 
Join Date: Jun 2011
Location: Athens & Chania,Greece
Posts: 143
Thanked 0 Times in 0 Posts
Default

Quote:
Originally Posted by BSDfan666 View Post
I don't believe OpenBSD's Xenocara has xorg.conf.d yet

That's true.That's why i created one. :-P

But i disagree; it is necessary since it's the only (known to me as i speak for myself) way so far to add a keyboard layout.I you have a better suggestion that works i would be glad to see it written here and try it.
Reply With Quote
Old 22nd September 2011
BSDfan666 BSDfan666 is offline
Real Name: N/A, this is the interweb.
Helpful companion
 
Join Date: Apr 2008
Location: Ontario, Canada
Posts: 2,223
Thanked 193 Times in 184 Posts
Default

Add it to xorg.conf?
Reply With Quote
Old 23rd September 2011
sepuku's Avatar
sepuku sepuku is offline
Real Name: Vizard Sepuku
Package Pilot
 
Join Date: Jun 2011
Location: Athens & Chania,Greece
Posts: 143
Thanked 0 Times in 0 Posts
Default

Quote:
Originally Posted by BSDfan666 View Post
Add it to xorg.conf?
From the first link that jggimi gave me:

"If you have an

/etc/X11/xorg.conf

file that exists mainly to set keyboard type and nationality that file should be removed, otherwise you may find yourself without keyboard functionality in X. "


I have removed that file a shown to "following -current" section.
Reply With Quote
Old 23rd September 2011
BSDfan666 BSDfan666 is offline
Real Name: N/A, this is the interweb.
Helpful companion
 
Join Date: Apr 2008
Location: Ontario, Canada
Posts: 2,223
Thanked 193 Times in 184 Posts
Default

In -current, the wscons infrastructure for X added auto configuration, you can still do manual xorg.conf configuration but you need to add Option "AutoAddDevices" "False" to the "ServerFlags" section.

They're trying to make it easier to run without an xorg.conf, but you still can.
Reply With Quote
Old 23rd September 2011
sepuku's Avatar
sepuku sepuku is offline
Real Name: Vizard Sepuku
Package Pilot
 
Join Date: Jun 2011
Location: Athens & Chania,Greece
Posts: 143
Thanked 0 Times in 0 Posts
Default

Quote:
Originally Posted by BSDfan666 View Post
In -current, the wscons infrastructure for X added auto configuration, you can still do manual xorg.conf configuration but you need to add Option "AutoAddDevices" "False" to the "ServerFlags" section.

They're trying to make it easier to run without an xorg.conf, but you still can.
I haven't tried that and it might work,but since my very first steps with OpenBSD everyone said that i should always read and follow the FAQ for a stable system.And even if your suggestion works i still dont get why mine is "unnecessary".Experimenting is always good and through it you gain a lot of experience but characterizing what worked for me unnecessary i think it's at least unfair.
Reply With Quote
Old 23rd September 2011
BSDfan666 BSDfan666 is offline
Real Name: N/A, this is the interweb.
Helpful companion
 
Join Date: Apr 2008
Location: Ontario, Canada
Posts: 2,223
Thanked 193 Times in 184 Posts
Default

Xorg is migrating the configuration to files inside xorg.conf.d, I simply meant you could use the traditional xorg.conf configuration method.

If you prefer to use the other method, that's fine, but I was simply stating you can still use a single xorg.conf config file, which IMHO is easier to maintain.
Reply With Quote
Old 23rd September 2011
sepuku's Avatar
sepuku sepuku is offline
Real Name: Vizard Sepuku
Package Pilot
 
Join Date: Jun 2011
Location: Athens & Chania,Greece
Posts: 143
Thanked 0 Times in 0 Posts
Default

Quote:
Originally Posted by BSDfan666 View Post
but I was simply stating you can still use a single xorg.conf config file, which IMHO is easier to maintain.
Well,i don't think that the contents of the new file have great differences compared to the old xorg .conf file.At least with everything that has to do with the layouts.Which is easier and more comfortable lays under someone's opinion.On the other hand it's a change that sooner or later will work only that way if i got it right and please correct me if i'm wrong.
Reply With Quote
Old 23rd September 2011
BSDfan666 BSDfan666 is offline
Real Name: N/A, this is the interweb.
Helpful companion
 
Join Date: Apr 2008
Location: Ontario, Canada
Posts: 2,223
Thanked 193 Times in 184 Posts
Default

No, I don't believe they'll be phasing out xorg.conf anytime soon.

Even if upstream eventually does, I'm not convinced OpenBSD's Xenocara fork will follow suit.
Reply With Quote
Old 23rd September 2011
sepuku's Avatar
sepuku sepuku is offline
Real Name: Vizard Sepuku
Package Pilot
 
Join Date: Jun 2011
Location: Athens & Chania,Greece
Posts: 143
Thanked 0 Times in 0 Posts
Default

Quote:
Originally Posted by BSDfan666 View Post
No, I don't believe they'll be phasing out xorg.conf anytime soon.

Even if upstream eventually does, I'm not convinced OpenBSD's Xenocara fork will follow suit.
Yet,i'll still try to follow what's in the FAQ.
Reply With Quote
Old 23rd September 2011
BSDfan666 BSDfan666 is offline
Real Name: N/A, this is the interweb.
Helpful companion
 
Join Date: Apr 2008
Location: Ontario, Canada
Posts: 2,223
Thanked 193 Times in 184 Posts
Default

OpenBSD FAQ refers to xorg.conf.d? I don't believe that is true.

Last edited by BSDfan666; 23rd September 2011 at 07:53 PM.
Reply With Quote
Reply

Tags
adding keyboard layouts, greek layout, openbsd5 snapshot

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Question about xenocara update and keyboard layout Daffy OpenBSD Installation and Upgrading 0 17th July 2011 11:35 AM
Keyboard Layout not included in encoding of wsksymdef.h sepuku OpenBSD General 8 4th July 2011 06:29 PM
NetBSD 5 keyboard layout in gnome jaideep_jdof NetBSD Package System (pkgsrc) 1 17th September 2009 03:50 PM
Can not change keyboard layout with SHIFT and Alt after VNCviewer connect mfaridi OpenBSD General 1 13th December 2008 03:14 PM
Keyboard Layout mfaridi FreeBSD General 6 26th June 2008 07:13 PM


All times are GMT. The time now is 06:12 PM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Content copyright © 2007-2010, the authors
Daemon image copyright ©1988, Marshall Kirk McKusick