DaemonForums  

Go Back   DaemonForums > NetBSD > NetBSD Installation and Upgrading

NetBSD Installation and Upgrading Have trouble getting NetBSD on your toaster?

Reply
 
Thread Tools Display Modes
  #1   (View Single Post)  
Old 30th January 2012
daemonfowl daemonfowl is offline
bsdstudent
 
Join Date: Jan 2012
Location: DaemonLand
Posts: 834
Thanked 0 Times in 0 Posts
Default Netbsd does't seem to detect bce0 ..

Hi everybody !
How are you ? I hope you're sound and safe ..

Yesterday I installed Netbsd on my 8g usb , out of curiosity .. it was a default full installation .. 4g swap+ rest for netbsd .. compared to OpenBSD boot it is a bit faster ..

while Netbsd detects on the fly my wpi0 and did't need any afterboot firmware install , it didn't detect my bce0 !
when I do #ifconfig -a .. it doesn't show but wpi0 and lo ..

Last edited by daemonfowl; 16th February 2012 at 05:02 PM.
Reply With Quote
  #2   (View Single Post)  
Old 16th February 2012
daemonfowl daemonfowl is offline
bsdstudent
 
Join Date: Jan 2012
Location: DaemonLand
Posts: 834
Thanked 0 Times in 0 Posts
Default

what I was trying to say :

on the same laptop : Acer Aspire 5610 :

* OpenBSD 5.0's ifconfig -a output:
Code:
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 33196
        priority: 0
        groups: lo
        inet6 ::1 prefixlen 128
        inet6 fe80::1%lo0 prefixlen 64 scopeid 0x4
        inet 127.0.0.1 netmask 0xff000000
wpi0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
        lladdr 00:19:d2:28:eb:bc
        priority: 4
        groups: wlan egress
        media: IEEE802.11 autoselect (OFDM54 mode 11g)
        status: active
        ieee80211: nwid Conceptronic chan 6 bssid 00:80:5a:5a:36:33 35dB
        inet6 fe80::219:d2ff:fe28:ebbc%wpi0 prefixlen 64 scopeid 0x1
        inet 192.168.1.2 netmask 0xffffff00 broadcast 192.168.1.255
bce0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> mtu 1500
        lladdr 00:16:d4:d2:d6:5e
        priority: 0
        media: Ethernet autoselect (none)
        status: no carrier
enc0: flags=0<>
        priority: 0
        groups: enc
        status: active
pflog0: flags=141<UP,RUNNING,PROMISC> mtu 33196
        priority: 0
        groups: pflog
* NetBSD 5.1's ifconfig -a output:
Code:
wpi0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
        ssid Conceptronic
        powersave off
        bssid 00:80:5a:5a:36:33 chan 6
        address: 00:19:d2:28:eb:bc
        media: IEEE802.11 autoselect (OFDM36 mode 11g)
        status: active
        inet 192.168.1.2 netmask 0xffffff00 broadcast 192.168.1.255
        inet6 fe80::219:d2ff:fe28:ebbc%wpi0 prefixlen 64 scopeid 0x1
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 33192
        inet 127.0.0.1 netmask 0xff000000
        inet6 ::1 prefixlen 128
        inet6 fe80::1%lo0 prefixlen 64 scopeid 0x2
Reply With Quote
  #3   (View Single Post)  
Old 16th February 2012
jggimi's Avatar
jggimi jggimi is offline
More noise than signal
 
Join Date: May 2008
Location: USA
Posts: 3,697
Thanked 214 Times in 189 Posts
Default

The root cause is likely to be discovered in your NetBSD dmesg(8).

See recommendation c.4. in http://www.daemonforums.org/showthread.php?t=596
Reply With Quote
  #4   (View Single Post)  
Old 16th February 2012
daemonfowl daemonfowl is offline
bsdstudent
 
Join Date: Jan 2012
Location: DaemonLand
Posts: 834
Thanked 0 Times in 0 Posts
Default

Hi Jgimmi ! thanks ..
I know I am still a BadNwb .. I feel reluctant to include dmesg every now and then unless if asked .. it feels bad filling pages with sth maybe unnecessary .. I am learning .. thank you for your patience ..

Code:
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
    2006, 2007, 2008, 2009, 2010
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 5.1 (GENERIC) #0: Sun Nov  7 14:39:56 UTC 2010
	builds@b6.netbsd.org:/home/builds/ab/netbsd-5-1-RELEASE/i386/201011061943Z-obj/home/builds/ab/netbsd-5-1-RELEASE/src/sys/arch/i386/compile/GENERIC
total memory = 2046 MB
avail memory = 1998 MB
timecounter: Timecounters tick every 10.000 msec
timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
Acer             Aspire 5610      (V3.50)
mainbus0 (root)
cpu0 at mainbus0 apid 0: Intel 686-class, 2939MHz, id 0x6e8
cpu0: Enhanced SpeedStep (1004 mV) 800 MHz
cpu0: Enhanced SpeedStep frequencies available (MHz): 1733 1600 1467 1333 1200 1067 933 800
cpu1 at mainbus0 apid 1: Intel 686-class, 2939MHz, id 0x6e8
ioapic0 at mainbus0 apid 1: pa 0xfec00000, version 20, 24 pins
acpi0 at mainbus0: Intel ACPICA 20080321
acpi0: X/RSDT: OemId <ACRSYS,ACRPRDCT,06040000>, AslId < LTP,00000000>
acpi0: SCI interrupting at int 9
acpi0: fixed-feature power button present
timecounter: Timecounter "ACPI-Fast" frequency 3579545 Hz quality 1000
ACPI-Fast 24-bit timer
acpilid0 at acpi0 (LID, PNP0C0D): ACPI Lid Switch
WMID (PNP0C14) at acpi0 not configured
acpibut0 at acpi0 (SLPB, PNP0C0E): ACPI Sleep Button
acpibut1 at acpi0 (PWRB, PNP0C0C): ACPI Power Button
acpiec0 at acpi0 (EC0, PNP0C09): io 0x62,0x66
acpibat0 at acpi0 (BAT1, PNP0C0A-1): ACPI Battery (Control Method)
acpibat0: battery info: SONY , Lion, GC86503SY90  
FWHD (INT0800) at acpi0 not configured
npx1 at acpi0 (MATH, PNP0C04): io 0xf0 irq 13
npx1: reported by CPUID; using exception 16
attimer1 at acpi0 (TIMR, PNP0100): io 0x40-0x43,0x50-0x53 irq 0
pckbc1 at acpi0 (PS2K, PNP0303) (kbd port): io 0x60,0x64 irq 1
pckbc2 at acpi0 (MSS0, SYN0703) (aux port): irq 12
acpiacad0 at acpi0 (ACAD, ACPI0003): ACPI AC Adapter
acpitz0 at acpi0 (TZ00): critical 127.0C, passive cooling
acpitz1 at acpi0 (TZ01): critical 85.0C passive 54.0C, passive cooling
apm0 at acpi0: Power Management spec V1.2
pckbd0 at pckbc1 (kbd slot)
pckbc1: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard
pms0 at pckbc1 (aux slot)
pms0: Synaptics touchpad version 6.2
pms0: Up/down buttons, Palm detect, Multi-finger
pckbc1: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0
pchb0: vendor 0x8086 product 0x27a0 (rev. 0x03)
agp0 at pchb0: can't find internal VGA device config space
ppb0 at pci0 dev 1 function 0: vendor 0x8086 product 0x27a1 (rev. 0x03)
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled, rd/line, wr/inv ok
vga1 at pci1 dev 0 function 0: vendor 0x10de product 0x01d7 (rev. 0xa1)
vga1: WARNING: ignoring 64-bit BAR @ 0x14
vga1: WARNING: ignoring 64-bit BAR @ 0x1c
wsdisplay0 at vga1 kbdmux 1: console (80x25, vt100 emulation), using wskbd0
wsmux1: connecting to wsdisplay0
drm at vga1 not configured
azalia0 at pci0 dev 27 function 0: Generic High Definition Audio Controller
azalia0: interrupting at ioapic0 pin 22
azalia0: host: 0x8086/0x27d8 (rev. 2), HDA rev. 1.0
ppb1 at pci0 dev 28 function 0: vendor 0x8086 product 0x27d0 (rev. 0x02)
ppb1: disabling notification events
pci2 at ppb1 bus 2
pci2: no spaces enabled!
ppb2 at pci0 dev 28 function 1: vendor 0x8086 product 0x27d2 (rev. 0x02)
ppb2: disabling notification events
pci3 at ppb2 bus 3
pci3: i/o space, memory space enabled, rd/line, wr/inv ok
ppb3 at pci0 dev 28 function 2: vendor 0x8086 product 0x27d4 (rev. 0x02)
pci4 at ppb3 bus 4
pci4: i/o space, memory space enabled, rd/line, wr/inv ok
ppb4 at pci0 dev 28 function 3: vendor 0x8086 product 0x27d6 (rev. 0x02)
ppb4: disabling notification events
pci5 at ppb4 bus 5
pci5: i/o space, memory space enabled, rd/line, wr/inv ok
wpi0 at pci5 dev 0 function 0: vendor 0x8086 product 0x4222 (rev. 0x02)
wpi0: interrupting at ioapic0 pin 19
wpi0: MoW2, address 00:19:d2:28:eb:bc
wpi0: 11a rates: 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
wpi0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
wpi0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
uhci0 at pci0 dev 29 function 0: vendor 0x8086 product 0x27c8 (rev. 0x02)
uhci0: interrupting at ioapic0 pin 23
usb0 at uhci0: USB revision 1.0
uhci1 at pci0 dev 29 function 1: vendor 0x8086 product 0x27c9 (rev. 0x02)
uhci1: interrupting at ioapic0 pin 19
usb1 at uhci1: USB revision 1.0
uhci2 at pci0 dev 29 function 2: vendor 0x8086 product 0x27ca (rev. 0x02)
uhci2: interrupting at ioapic0 pin 18
usb2 at uhci2: USB revision 1.0
uhci3 at pci0 dev 29 function 3: vendor 0x8086 product 0x27cb (rev. 0x02)
uhci3: interrupting at ioapic0 pin 16
usb3 at uhci3: USB revision 1.0
ehci0 at pci0 dev 29 function 7: vendor 0x8086 product 0x27cc (rev. 0x02)
ehci0: interrupting at ioapic0 pin 23
ehci0: EHCI version 1.0
ehci0: companion controllers, 2 ports each: uhci0 uhci1 uhci2 uhci3
usb4 at ehci0: USB revision 2.0
ppb5 at pci0 dev 30 function 0: vendor 0x8086 product 0x2448 (rev. 0xe2)
pci6 at ppb5 bus 6
pci6: no spaces enabled!
ichlpcib0 at pci0 dev 31 function 0
ichlpcib0: vendor 0x8086 product 0x27b9 (rev. 0x02)
timecounter: Timecounter "ichlpcib0" frequency 3579545 Hz quality 1000
ichlpcib0: 24-bit timer
ichlpcib0: TCO (watchdog) timer configured.
piixide0 at pci0 dev 31 function 2
piixide0: Intel 82801GBM/GHM Serial ATA Controller (ICH7) (rev. 0x02)
piixide0: bus-master DMA support present
piixide0: primary channel wired to compatibility mode
piixide0: primary channel interrupting at ioapic0 pin 14
atabus0 at piixide0 channel 0
piixide0: secondary channel wired to compatibility mode
piixide0: secondary channel interrupting at ioapic0 pin 15
atabus1 at piixide0 channel 1
ichsmb0 at pci0 dev 31 function 3: vendor 0x8086 product 0x27da (rev. 0x02)
ichsmb0: interrupting at ioapic0 pin 19
iic0 at ichsmb0: I2C bus
isa0 at ichlpcib0
pcppi0 at isa0 port 0x61
midi0 at pcppi0: PC speaker (CPU-intensive output)
sysbeep0 at pcppi0
pcic0 at isa0 port 0x3e0-0x3e1 iomem 0xd0000-0xdffff irq 
pcic0: controller 0 (Intel 82365SL-DF) has socket A only
pcmcia0 at pcic0 controller 0 socket 0
attimer1: attached to pcppi0
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
timecounter: Timecounter "TSC" frequency 2939504750 Hz quality 3000
azalia0: codec[0]: Realtek ALC883 (rev. 0.2), HDA rev. 1.0
azalia0: codec[1]: 0x14f1/0x2c06 (rev. 0.0), HDA rev. 1.0
azalia0: codec[1]: No support for modem function groups
azalia0: codec[1] has no audio function groups
audio0 at azalia0: full duplex, playback, capture, independent
pcic0: controller 0 detecting irqs with mask 0xdeb8: none
pcic0: no available irq; polling for socket events
pcic0: WARNING: powerhook_establish is deprecated
acpiacad0: AC adapter online.
uhub0 at usb0: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhub1 at usb1: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhub2 at usb2: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
uhub3 at usb3: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub3: 2 ports with 2 removable, self powered
uhub4 at usb4: vendor 0x8086 EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub4: 8 ports with 8 removable, self powered
umass0 at uhub4 port 3 configuration 1 interface 0
umass0: Kingston DataTraveler G2, rev 2.00/1.10, addr 2
umass0: using SCSI over Bulk-Only
scsibus0 at umass0: 2 targets, 1 lun per target
sd0 at scsibus0 target 0 lun 0: <Kingston, DataTraveler G2, PMAP> disk removable
sd0: 15320 MB, 3845 cyl, 255 head, 32 sec, 512 bytes/sect x 31375360 sectors
uvideo0 at uhub4 port 4 configuration 1 interface 0: vendor 0x046d product 0x09b0, rev 2.00/0.06, addr 3
video0 at uvideo0: vendor 0x046d product 0x09b0, rev 2.00/0.06, addr 3
wd0 at atabus0 drive 0: <TOSHIBA MK5076GSX>
wd0: drive supports 16-sector PIO transfers, LBA48 addressing
wd0: 465 GB, 969021 cyl, 16 head, 63 sec, 512 bytes/sect x 976773168 sectors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
wd0(piixide0:0:0): using PIO mode 4, Ultra-DMA mode 5 (Ultra/100) (using DMA)
atapibus0 at atabus1: 2 targets
cd0 at atapibus0 drive 0: <Optiarc DVD RW AD-7590A, , 1.04> cdrom removable
cd0: 32-bit data port
cd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 2 (Ultra/33)
cd0(piixide0:1:0): using PIO mode 4, Ultra-DMA mode 2 (Ultra/33) (using DMA)
Kernelized RAIDframe activated
pad0: outputs: 44100Hz, 16-bit, stereo
audio1 at pad0: half duplex, playback, capture
boot device: sd0
root on sd0a dumps on sd0b
root file system type: ffs
wsdisplay0: screen 1 added (80x25, vt100 emulation)
wsdisplay0: screen 2 added (80x25, vt100 emulation)
wsdisplay0: screen 3 added (80x25, vt100 emulation)
wsdisplay0: screen 4 added (80x25, vt100 emulation)
Reply With Quote
  #5   (View Single Post)  
Old 16th February 2012
ocicat ocicat is offline
Administrator
 
Join Date: Apr 2008
Posts: 2,888
Thanked 190 Times in 160 Posts
Default

Quote:
Originally Posted by daemonfowl View Post
I feel reluctant to include dmesg every now and then unless if asked .. it feels bad filling pages with sth maybe unnecessary
It is never a bad idea to post dmesg(8) output. Many collateral questions can be answered by knowing how the kernel is identifying hardware.
Reply With Quote
  #6   (View Single Post)  
Old 17th February 2012
daemonfowl daemonfowl is offline
bsdstudent
 
Join Date: Jan 2012
Location: DaemonLand
Posts: 834
Thanked 0 Times in 0 Posts
Default

you are right Ocicat .. just sometimes I wonder if there is sth in the dmesg output that may reveal some Achilles' heel .. MAC or sth .. I don't know really ..
Reply With Quote
  #7   (View Single Post)  
Old 17th February 2012
ocicat ocicat is offline
Administrator
 
Join Date: Apr 2008
Posts: 2,888
Thanked 190 Times in 160 Posts
Default

Quote:
Originally Posted by daemonfowl View Post
I wonder if there is sth in the dmesg output...
What's a "sth"?

Reply With Quote
  #8   (View Single Post)  
Old 17th February 2012
daemonfowl daemonfowl is offline
bsdstudent
 
Join Date: Jan 2012
Location: DaemonLand
Posts: 834
Thanked 0 Times in 0 Posts
Default

sorry , an abbreviated 'something' ..
Reply With Quote
  #9   (View Single Post)  
Old 17th February 2012
ocicat ocicat is offline
Administrator
 
Join Date: Apr 2008
Posts: 2,888
Thanked 190 Times in 160 Posts
Default

Quote:
Originally Posted by daemonfowl View Post
...an abbreviated 'something' ..
As we are ascertaining that English is not your first language, English is not the first language of many of our members. Using abbreviations is fine if they are common to technical literature. Abbreviations used in text messaging is discouraged, as not everyone uses/understands them.

The goal each poster should attempt to make is to provide clarity to an audience which may be at different levels of language proficiency, & come from different cultural backgrounds. Some may see this as advocating blandness, but clear & concise communication is far more important in an arena where the only way we communicate with each other is through forum posts.

Technical discussions have enough problems. We don't need to complicate the communication further by using descriptions no one understands.
Reply With Quote
Old 17th February 2012
daemonfowl daemonfowl is offline
bsdstudent
 
Join Date: Jan 2012
Location: DaemonLand
Posts: 834
Thanked 0 Times in 0 Posts
Default

Thanks for pointing out .. I totally approve of this approach !
sometimes bad habit comes in the way ..
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
How to make DesktopBSD detect re0? KlaymenDK Other BSD and UNIX/UNIX-like 9 6th January 2009 09:40 PM
How to detect the frequency of individual cores in a dual core processor? mc_i2020 FreeBSD General 5 18th July 2008 01:46 AM


All times are GMT. The time now is 12:31 PM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Content copyright © 2007-2010, the authors
Daemon image copyright ©1988, Marshall Kirk McKusick