DaemonForums  

Go Back   DaemonForums > OpenBSD > OpenBSD General

OpenBSD General Other questions regarding OpenBSD which do not fit in any of the categories below.

Reply
 
Thread Tools Display Modes
  #1   (View Single Post)  
Old 25th February 2012
Daffy Daffy is offline
Fdisk Soldier
 
Join Date: Jun 2010
Posts: 73
Thanked 0 Times in 0 Posts
Default Configuring X with 9800gt fails.

As someone brought me today a new graphics card (NVidia GeForce 9800GT), I saw it was a nice idea to try it.

Reading the nv(4), I saw that there is support for this card.

But while doing X -configure, I get the following error:
Code:
X.Org X Server 1.11.4
Release Date: 2012-01-27
X Protocol Version 11, Revision 0
Build Operating System: OpenBSD 5.1 i386 
Current Operating System: OpenBSD ducks.lan 5.1 GENERIC.MP#188 i386
Build Date: 11 February 2012  10:00:22PM
 
Current version of pixman: 0.22.2
        Before reporting problems, check http://wiki.x.org
        to make sure that you have the latest version.
Markers: (--) probed, (**) from config file, (==) default setting,
        (++) from command line, (!!) notice, (II) informational,
        (WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/Xorg.0.log", Time: Sat Feb 25 06:06:25 2012
List of video drivers:
        apm
        ark
        ati
        chips
        cirrus
        dummy
        geode
        glint
        i128
        i740
        intel
        mach64
        mga
        neomagic
        nv
        openchrome
        r128
        radeon
        radeonhd
        rendition
        s3
        s3virge
        savage
        siliconmotion
        sis
        tdfx
        trident
        tseng
        wsudl
        vmware
        vmwlegacy
        voodoo
        vesa
X:/usr/X11R6/lib/modules/drivers/radeonhd_drv.so: /usr/X11R6/lib/modules/drivers/radeon_drv.so : WARNING: symbol(AtomBiosRequestList) size mismatch, relink your program
(EE) Failed to load module "vmwgfx" (module does not exist, 0)
(EE) vmware: Please ignore the above warnings about not being able to to load module/driver vmwgfx
(++) Using config file: "/root/xorg.conf.new"
(==) Using system config directory "/usr/X11R6/share/X11/xorg.conf.d"
Number of created screens does not match number of detected devices.
  Configuration failed.
Server terminated with error (2). Closing log file.
Am I reading something wrong in the man page and this card is not supported?
I know about the state of NVidia open divers (or the lack of to be exact ), but a free card is always a temptation. hehe

(massive dmesg follows)

Code:
OpenBSD 5.1 (GENERIC.MP) #188: Sun Feb 12 09:55:11 MST 2012
    deraadt@i386.openbsd.org:/usr/src/sys/arch/i386/compile/GENERIC.MP
cpu0: Intel(R) Core(TM)2 Duo CPU E4500 @ 2.20GHz ("GenuineIntel" 686-class) 2.21 GHz
cpu0: FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,SBF,NXE,LONG,SSE3,MWAIT,DS-CPL,EST,TM2,SSSE3,CX16,xTPR,PDCM,LAHF
real mem  = 3488673792 (3327MB)
avail mem = 3421499392 (3262MB)
mainbus0 at root
bios0 at mainbus0: AT/286+ BIOS, date 08/20/08, BIOS32 rev. 0 @ 0xf0010, SMBIOS rev. 2.5 @ 0xf0710 (61 entries)
bios0: vendor American Megatrends Inc. version "0611" date 08/20/2008
bios0: ASUSTeK Computer INC. P5QL-E
acpi0 at bios0: rev 0
acpi0: sleep states S0 S1 S3 S4 S5
acpi0: tables DSDT FACP APIC MCFG OEMB HPET OSFR
acpi0: wakeup devices P0P2(S4) P0P3(S4) P0P1(S4) UAR1(S4) PS2K(S4) PS2M(S4) EUSB(S4) USBE(S4) P0P5(S4) P0P6(S4) P0P7(S4) P0P8(S4) P0P9(S4) GBEC(S4) USB0(S4) USB1(S4) USB2(S4) USB3(S4) USB4(S4) USB5(S4) USB6(S4) P0P4(S4)
acpitimer0 at acpi0: 3579545 Hz, 24 bits
acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat
cpu0 at mainbus0: apid 0 (boot processor)
cpu0: apic clock running at 200MHz
cpu1 at mainbus0: apid 1 (application processor)
cpu1: Intel(R) Core(TM)2 Duo CPU E4500 @ 2.20GHz ("GenuineIntel" 686-class) 2.21 GHz
cpu1: FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,SBF,NXE,LONG,SSE3,MWAIT,DS-CPL,EST,TM2,SSSE3,CX16,xTPR,PDCM,LAHF
ioapic0 at mainbus0: apid 2 pa 0xfec00000, version 20, 24 pins
acpimcfg0 at acpi0 addr 0xe0000000, bus 0-255
acpihpet0 at acpi0: 14318179 Hz
acpiprt0 at acpi0: bus 0 (PCI0)
acpiprt1 at acpi0: bus 1 (P0P2)
acpiprt2 at acpi0: bus -1 (P0P3)
acpiprt3 at acpi0: bus 5 (P0P1)
acpiprt4 at acpi0: bus -1 (P0P5)
acpiprt5 at acpi0: bus 3 (P0P8)
acpiprt6 at acpi0: bus 2 (P0P9)
acpiprt7 at acpi0: bus 4 (P0P4)
acpicpu0 at acpi0
acpicpu1 at acpi0
aibs0 at acpi0: RTMP RVLT RFAN GGRP GITM SITM
acpibtn0 at acpi0: PWRB
bios0: ROM list: 0xc0000/0xd200 0xcd800/0x3000!
pci0 at mainbus0 bus 0: configuration mode 1 (bios)
pchb0 at pci0 dev 0 function 0 "Intel G45 Host" rev 0x03
ppb0 at pci0 dev 1 function 0 "Intel G45 PCIE" rev 0x03: apic 2 int 16
pci1 at ppb0 bus 1
vga1 at pci1 dev 0 function 0 "NVIDIA GeForce 9800 GT" rev 0xa2
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
uhci0 at pci0 dev 26 function 0 "Intel 82801JI USB" rev 0x00: apic 2 int 16
uhci1 at pci0 dev 26 function 1 "Intel 82801JI USB" rev 0x00: apic 2 int 21
uhci2 at pci0 dev 26 function 2 "Intel 82801JI USB" rev 0x00: apic 2 int 18
ehci0 at pci0 dev 26 function 7 "Intel 82801JI USB" rev 0x00: apic 2 int 18
usb0 at ehci0: USB revision 2.0
uhub0 at usb0 "Intel EHCI root hub" rev 2.00/1.00 addr 1
azalia0 at pci0 dev 27 function 0 "Intel 82801JI HD Audio" rev 0x00: msi
azalia0: codecs: Realtek ALC888
audio0 at azalia0
ppb1 at pci0 dev 28 function 0 "Intel 82801JI PCIE" rev 0x00: apic 2 int 17
pci2 at ppb1 bus 4
ppb2 at pci0 dev 28 function 4 "Intel 82801JI PCIE" rev 0x00: apic 2 int 17
pci3 at ppb2 bus 3
jmb0 at pci3 dev 0 function 0 "JMicron JMB363 IDE/SATA" rev 0x03
ahci0 at jmb0: apic 2 int 16, AHCI 1.0
scsibus0 at ahci0: 32 targets
pciide0 at jmb0: DMA, channel 0 wired to native-PCI, channel 1 wired to native-PCI
pciide0: using apic 2 int 16 for native-PCI interrupt
atapiscsi0 at pciide0 channel 0 drive 0
scsibus1 at atapiscsi0: 2 targets
cd0 at scsibus1 targ 0 lun 0: <HL-DT-ST, DVD-RAM GSA-H55L, 1.03> ATAPI 5/cdrom removable
wd0 at pciide0 channel 0 drive 1: <ST3160812A>
wd0: 16-sector PIO, LBA48, 152627MB, 312581808 sectors
cd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 4
wd0(pciide0:0:1): using PIO mode 4, Ultra-DMA mode 5
pciide0: channel 1 disabled (no drives)
ppb3 at pci0 dev 28 function 5 "Intel 82801JI PCIE" rev 0x00: apic 2 int 16
pci4 at ppb3 bus 2
ale0 at pci4 dev 0 function 0 "Attansic Technology L1E" rev 0xb0: AR8121, msi, address 00:22:15:fd:48:74
atphy0 at ale0 phy 0: F1 10/100/1000 PHY, rev. 9
uhci3 at pci0 dev 29 function 0 "Intel 82801JI USB" rev 0x00: apic 2 int 23
uhci4 at pci0 dev 29 function 1 "Intel 82801JI USB" rev 0x00: apic 2 int 19
uhci5 at pci0 dev 29 function 2 "Intel 82801JI USB" rev 0x00: apic 2 int 18
ehci1 at pci0 dev 29 function 7 "Intel 82801JI USB" rev 0x00: apic 2 int 23
usb1 at ehci1: USB revision 2.0
uhub1 at usb1 "Intel EHCI root hub" rev 2.00/1.00 addr 1
ppb4 at pci0 dev 30 function 0 "Intel 82801BA Hub-to-PCI" rev 0x90
pci5 at ppb4 bus 5
pcib0 at pci0 dev 31 function 0 "Intel 82801JIR LPC" rev 0x00
pciide1 at pci0 dev 31 function 2 "Intel 82801JI SATA" rev 0x00: DMA, channel 0 configured to native-PCI, channel 1 configured to native-PCI
pciide1: using apic 2 int 19 for native-PCI interrupt
ichiic0 at pci0 dev 31 function 3 "Intel 82801JI SMBus" rev 0x00: apic 2 int 18
iic0 at ichiic0
iic0: addr 0x1e 01=01 02=01 11=01 12=01 21=01 22=01 31=01 32=01 words 00=0001 01=0101 02=0100 03=0000 04=0000 05=0000 06=0000 07=0000
iic0: addr 0x20 01=80 02=17 03=7f 10=00 19=b0 20=20 21=00 25=20 26=b2 38=74 39=03 4a=64 6a=2c 78=02 79=08 7a=00 7b=00 7e=82 80=00 8b=41 8c=5b 96=03 99=41 9a=98 9b=01 d0=00 d1=03 d2=72 d3=72 d4=03 d5=02 d6=01 d7=67 d8=69 d9=00 da=00 db=00 dc=00 dd=00 de=00 df=19 e0=00 e1=00 e2=10 e3=10 e4=10 e5=10 e6=10 e7=10 e8=10 e9=10 ea=10 ec=07 ee=00 f1=0b f5=02 f6=02 f9=00 fa=00 fb=50 words 00=ffff 01=8037 02=1766 03=7fff 04=ffff 05=ffff 06=ffff 07=ffff
spdmem0 at iic0 addr 0x50: 1GB DDR2 SDRAM non-parity PC2-6400CL5
spdmem1 at iic0 addr 0x52: 1GB DDR2 SDRAM non-parity PC2-6400CL5
spdmem2 at iic0 addr 0x53: 2GB DDR2 SDRAM non-parity PC2-6400CL5
pciide2 at pci0 dev 31 function 5 "Intel 82801JI SATA" rev 0x00: DMA, channel 0 wired to native-PCI, channel 1 wired to native-PCI
pciide2: using apic 2 int 19 for native-PCI interrupt
usb2 at uhci0: USB revision 1.0
uhub2 at usb2 "Intel UHCI root hub" rev 1.00/1.00 addr 1
usb3 at uhci1: USB revision 1.0
uhub3 at usb3 "Intel UHCI root hub" rev 1.00/1.00 addr 1
usb4 at uhci2: USB revision 1.0
uhub4 at usb4 "Intel UHCI root hub" rev 1.00/1.00 addr 1
usb5 at uhci3: USB revision 1.0
uhub5 at usb5 "Intel UHCI root hub" rev 1.00/1.00 addr 1
usb6 at uhci4: USB revision 1.0
uhub6 at usb6 "Intel UHCI root hub" rev 1.00/1.00 addr 1
usb7 at uhci5: USB revision 1.0
uhub7 at usb7 "Intel UHCI root hub" rev 1.00/1.00 addr 1
isa0 at pcib0
isadma0 at isa0
com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pms0 at pckbc0 (aux slot)
pckbc0: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
pcppi0 at isa0 port 0x61
spkr0 at pcppi0
lm0 at isa0 port 0x290/8: W83627DHG
npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
mtrr: Pentium Pro MTRR support
vscsi0 at root
scsibus2 at vscsi0: 256 targets
softraid0 at root
scsibus3 at softraid0: 256 targets
root on wd0a (952ef3f9a030fe08.a) swap on wd0b dump on wd0b
syncing disks... 
OpenBSD 5.1 (GENERIC.MP) #188: Sun Feb 12 09:55:11 MST 2012
    deraadt@i386.openbsd.org:/usr/src/sys/arch/i386/compile/GENERIC.MP
cpu0: Intel(R) Core(TM)2 Duo CPU E4500 @ 2.20GHz ("GenuineIntel" 686-class) 2.21 GHz
cpu0: FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,SBF,NXE,LONG,SSE3,MWAIT,DS-CPL,EST,TM2,SSSE3,CX16,xTPR,PDCM,LAHF
real mem  = 3488673792 (3327MB)
avail mem = 3421499392 (3262MB)
mainbus0 at root
bios0 at mainbus0: AT/286+ BIOS, date 08/20/08, BIOS32 rev. 0 @ 0xf0010, SMBIOS rev. 2.5 @ 0xf0710 (61 entries)
bios0: vendor American Megatrends Inc. version "0611" date 08/20/2008
bios0: ASUSTeK Computer INC. P5QL-E
acpi0 at bios0: rev 0
acpi0: sleep states S0 S1 S3 S4 S5
acpi0: tables DSDT FACP APIC MCFG OEMB HPET OSFR
acpi0: wakeup devices P0P2(S4) P0P3(S4) P0P1(S4) UAR1(S4) PS2K(S4) PS2M(S4) EUSB(S4) USBE(S4) P0P5(S4) P0P6(S4) P0P7(S4) P0P8(S4) P0P9(S4) GBEC(S4) USB0(S4) USB1(S4) USB2(S4) USB3(S4) USB4(S4) USB5(S4) USB6(S4) P0P4(S4)
acpitimer0 at acpi0: 3579545 Hz, 24 bits
acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat
cpu0 at mainbus0: apid 0 (boot processor)
cpu0: apic clock running at 200MHz
cpu1 at mainbus0: apid 1 (application processor)
cpu1: Intel(R) Core(TM)2 Duo CPU E4500 @ 2.20GHz ("GenuineIntel" 686-class) 2.21 GHz
cpu1: FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,SBF,NXE,LONG,SSE3,MWAIT,DS-CPL,EST,TM2,SSSE3,CX16,xTPR,PDCM,LAHF
ioapic0 at mainbus0: apid 2 pa 0xfec00000, version 20, 24 pins
acpimcfg0 at acpi0 addr 0xe0000000, bus 0-255
acpihpet0 at acpi0: 14318179 Hz
acpiprt0 at acpi0: bus 0 (PCI0)
acpiprt1 at acpi0: bus 1 (P0P2)
acpiprt2 at acpi0: bus -1 (P0P3)
acpiprt3 at acpi0: bus 5 (P0P1)
acpiprt4 at acpi0: bus -1 (P0P5)
acpiprt5 at acpi0: bus 3 (P0P8)
acpiprt6 at acpi0: bus 2 (P0P9)
acpiprt7 at acpi0: bus 4 (P0P4)
acpicpu0 at acpi0
acpicpu1 at acpi0
aibs0 at acpi0: RTMP RVLT RFAN GGRP GITM SITM
acpibtn0 at acpi0: PWRB
bios0: ROM list: 0xc0000/0xd200 0xcd800/0x3000!
pci0 at mainbus0 bus 0: configuration mode 1 (bios)
pchb0 at pci0 dev 0 function 0 "Intel G45 Host" rev 0x03
ppb0 at pci0 dev 1 function 0 "Intel G45 PCIE" rev 0x03: apic 2 int 16
pci1 at ppb0 bus 1
vga1 at pci1 dev 0 function 0 "NVIDIA GeForce 9800 GT" rev 0xa2
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
uhci0 at pci0 dev 26 function 0 "Intel 82801JI USB" rev 0x00: apic 2 int 16
uhci1 at pci0 dev 26 function 1 "Intel 82801JI USB" rev 0x00: apic 2 int 21
uhci2 at pci0 dev 26 function 2 "Intel 82801JI USB" rev 0x00: apic 2 int 18
ehci0 at pci0 dev 26 function 7 "Intel 82801JI USB" rev 0x00: apic 2 int 18
usb0 at ehci0: USB revision 2.0
uhub0 at usb0 "Intel EHCI root hub" rev 2.00/1.00 addr 1
azalia0 at pci0 dev 27 function 0 "Intel 82801JI HD Audio" rev 0x00: msi
azalia0: codecs: Realtek ALC888
audio0 at azalia0
ppb1 at pci0 dev 28 function 0 "Intel 82801JI PCIE" rev 0x00: apic 2 int 17
pci2 at ppb1 bus 4
ppb2 at pci0 dev 28 function 4 "Intel 82801JI PCIE" rev 0x00: apic 2 int 17
pci3 at ppb2 bus 3
jmb0 at pci3 dev 0 function 0 "JMicron JMB363 IDE/SATA" rev 0x03
ahci0 at jmb0: apic 2 int 16, AHCI 1.0
scsibus0 at ahci0: 32 targets
pciide0 at jmb0: DMA, channel 0 wired to native-PCI, channel 1 wired to native-PCI
pciide0: using apic 2 int 16 for native-PCI interrupt
atapiscsi0 at pciide0 channel 0 drive 0
scsibus1 at atapiscsi0: 2 targets
cd0 at scsibus1 targ 0 lun 0: <HL-DT-ST, DVD-RAM GSA-H55L, 1.03> ATAPI 5/cdrom removable
wd0 at pciide0 channel 0 drive 1: <ST3160812A>
wd0: 16-sector PIO, LBA48, 152627MB, 312581808 sectors
cd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 4
wd0(pciide0:0:1): using PIO mode 4, Ultra-DMA mode 5
pciide0: channel 1 disabled (no drives)
ppb3 at pci0 dev 28 function 5 "Intel 82801JI PCIE" rev 0x00: apic 2 int 16
pci4 at ppb3 bus 2
ale0 at pci4 dev 0 function 0 "Attansic Technology L1E" rev 0xb0: AR8121, msi, address 00:22:15:fd:48:74
atphy0 at ale0 phy 0: F1 10/100/1000 PHY, rev. 9
uhci3 at pci0 dev 29 function 0 "Intel 82801JI USB" rev 0x00: apic 2 int 23
uhci4 at pci0 dev 29 function 1 "Intel 82801JI USB" rev 0x00: apic 2 int 19
uhci5 at pci0 dev 29 function 2 "Intel 82801JI USB" rev 0x00: apic 2 int 18
ehci1 at pci0 dev 29 function 7 "Intel 82801JI USB" rev 0x00: apic 2 int 23
usb1 at ehci1: USB revision 2.0
uhub1 at usb1 "Intel EHCI root hub" rev 2.00/1.00 addr 1
ppb4 at pci0 dev 30 function 0 "Intel 82801BA Hub-to-PCI" rev 0x90
pci5 at ppb4 bus 5
pcib0 at pci0 dev 31 function 0 "Intel 82801JIR LPC" rev 0x00
pciide1 at pci0 dev 31 function 2 "Intel 82801JI SATA" rev 0x00: DMA, channel 0 configured to native-PCI, channel 1 configured to native-PCI
pciide1: using apic 2 int 19 for native-PCI interrupt
ichiic0 at pci0 dev 31 function 3 "Intel 82801JI SMBus" rev 0x00: apic 2 int 18
iic0 at ichiic0
iic0: addr 0x1e 01=01 02=01 11=01 12=01 21=01 22=01 31=01 32=01 words 00=0001 01=0101 02=0100 03=0000 04=0000 05=0000 06=0000 07=0000
iic0: addr 0x20 01=80 02=17 03=7f 10=00 19=b0 20=20 21=00 25=20 26=b2 38=74 39=03 4a=64 6a=2c 78=02 79=08 7a=00 7b=00 7e=82 80=00 8b=41 8c=78 96=0c 99=41 9a=98 9b=01 d0=00 d1=03 d2=72 d3=72 d4=03 d5=02 d6=01 d7=67 d8=69 d9=00 da=00 db=00 dc=00 dd=00 de=00 df=19 e0=00 e1=00 e2=10 e3=10 e4=10 e5=10 e6=10 e7=10 e8=10 e9=10 ea=10 ec=07 ee=00 f1=0c f5=02 f6=02 f9=00 fa=00 fb=50 words 00=ffff 01=8037 02=1766 03=7fff 04=ffff 05=ffff 06=ffff 07=ffff
spdmem0 at iic0 addr 0x50: 1GB DDR2 SDRAM non-parity PC2-6400CL5
spdmem1 at iic0 addr 0x52: 1GB DDR2 SDRAM non-parity PC2-6400CL5
spdmem2 at iic0 addr 0x53: 2GB DDR2 SDRAM non-parity PC2-6400CL5
pciide2 at pci0 dev 31 function 5 "Intel 82801JI SATA" rev 0x00: DMA, channel 0 wired to native-PCI, channel 1 wired to native-PCI
pciide2: using apic 2 int 19 for native-PCI interrupt
usb2 at uhci0: USB revision 1.0
uhub2 at usb2 "Intel UHCI root hub" rev 1.00/1.00 addr 1
usb3 at uhci1: USB revision 1.0
uhub3 at usb3 "Intel UHCI root hub" rev 1.00/1.00 addr 1
usb4 at uhci2: USB revision 1.0
uhub4 at usb4 "Intel UHCI root hub" rev 1.00/1.00 addr 1
usb5 at uhci3: USB revision 1.0
uhub5 at usb5 "Intel UHCI root hub" rev 1.00/1.00 addr 1
usb6 at uhci4: USB revision 1.0
uhub6 at usb6 "Intel UHCI root hub" rev 1.00/1.00 addr 1
usb7 at uhci5: USB revision 1.0
uhub7 at usb7 "Intel UHCI root hub" rev 1.00/1.00 addr 1
isa0 at pcib0
isadma0 at isa0
com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pms0 at pckbc0 (aux slot)
pckbc0: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
pcppi0 at isa0 port 0x61
spkr0 at pcppi0
lm0 at isa0 port 0x290/8: W83627DHG
npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
mtrr: Pentium Pro MTRR support
vscsi0 at root
scsibus2 at vscsi0: 256 targets
softraid0 at root
scsibus3 at softraid0: 256 targets
root on wd0a (952ef3f9a030fe08.a) swap on wd0b dump on wd0b
Reply With Quote
  #2   (View Single Post)  
Old 26th February 2012
J65nko J65nko is offline
Administrator
 
Join Date: May 2008
Location: Budel - the Netherlands
Posts: 3,141
Thanked 182 Times in 149 Posts
Default

How does the generated xorg.conf look like?
__________________
You don't need to be a genius to debug a pf.conf firewall ruleset, you just need the guts to run tcpdump
Reply With Quote
  #3   (View Single Post)  
Old 26th February 2012
Daffy Daffy is offline
Fdisk Soldier
 
Join Date: Jun 2010
Posts: 73
Thanked 0 Times in 0 Posts
Default

Quote:
Originally Posted by J65nko View Post
How does the generated xorg.conf look like?
Ugh... Keep forgetting things...

There we go:
Code:
Section "ServerLayout"
        Identifier     "X.org Configured"
        Screen      0  "Screen0" 0 0
        Screen      1  "Screen1" RightOf "Screen0"
        InputDevice    "Mouse0" "CorePointer"
        InputDevice    "Keyboard0" "CoreKeyboard"
EndSection

Section "Files"
        ModulePath   "/usr/X11R6/lib/modules"
        FontPath     "/usr/X11R6/lib/X11/fonts/misc/"
        FontPath     "/usr/X11R6/lib/X11/fonts/TTF/"
        FontPath     "/usr/X11R6/lib/X11/fonts/OTF/"
        FontPath     "/usr/X11R6/lib/X11/fonts/Type1/"
        FontPath     "/usr/X11R6/lib/X11/fonts/100dpi/"
        FontPath     "/usr/X11R6/lib/X11/fonts/75dpi/"
EndSection

Section "Module"
        Load  "dbe"
        Load  "dri"
        Load  "dri2"
        Load  "extmod"
        Load  "glx"
        Load  "record"
EndSection

Section "InputDevice"
        Identifier  "Keyboard0"
        Driver      "kbd"
EndSection

Section "InputDevice"
        Identifier  "Mouse0"
        Driver      "mouse"
        Option      "Protocol" "wsmouse"
        Option      "Device" "/dev/wsmouse"
        Option      "ZAxisMapping" "4 5 6 7"
EndSection

Section "Monitor"
        Identifier   "Monitor0"
        VendorName   "Monitor Vendor"
        ModelName    "Monitor Model"
EndSection

Section "Monitor"
        Identifier   "Monitor1"
        VendorName   "Monitor Vendor"
        ModelName    "Monitor Model"
EndSection

Section "Device"
        ### Available Driver options are:-
        ### Values: <i>: integer, <f>: float, <bool>: "True"/"False",
        ### <string>: "String", <freq>: "<f> Hz/kHz/MHz",
        ### <percent>: "<f>%"
        ### [arg]: arg optional
        #Option     "SWcursor"                  # [<bool>]
        #Option     "HWcursor"                  # [<bool>]
        #Option     "NoAccel"                   # [<bool>]
        #Option     "ShadowFB"                  # [<bool>]
        #Option     "UseFBDev"                  # [<bool>]
        #Option     "Rotate"                    # [<str>]
        #Option     "VideoKey"                  # <i>
        #Option     "FlatPanel"                 # [<bool>]
        #Option     "FPDither"                  # [<bool>]
        #Option     "CrtcNumber"                # <i>
        #Option     "FPScale"                   # [<bool>]
        #Option     "FPTweak"                   # <i>
        #Option     "DualHead"                  # [<bool>]
        Identifier  "Card0"
        Driver      "nv"
        BusID       "PCI:1:0:0"
EndSection

Section "Device"
        ### Available Driver options are:-
        ### Values: <i>: integer, <f>: float, <bool>: "True"/"False",
        ### <string>: "String", <freq>: "<f> Hz/kHz/MHz",
        ### <percent>: "<f>%"
        ### [arg]: arg optional
        #Option     "ShadowFB"                  # [<bool>]
        #Option     "DefaultRefresh"            # [<bool>]
        #Option     "ModeSetClearScreen"        # [<bool>]
        Identifier  "Card1"
        Driver      "vesa"
        BusID       "PCI:1:0:0"
EndSection

Section "Screen"
        Identifier "Screen0"
        Device     "Card0"
        Monitor    "Monitor0"
        SubSection "Display"
                Viewport   0 0
                Depth     1
        EndSubSection
        SubSection "Display"
                Viewport   0 0
                Depth     4
        EndSubSection
        SubSection "Display"
                Viewport   0 0
                Depth     8
        EndSubSection
        SubSection "Display"
                Viewport   0 0
                Depth     15
        EndSubSection
        SubSection "Display"
                Viewport   0 0
                Depth     16
        EndSubSection
        SubSection "Display"
                Viewport   0 0
                Depth     24
        EndSubSection
EndSection

Section "Screen"
        Identifier "Screen1"
        Device     "Card1"
        Monitor    "Monitor1"
        SubSection "Display"
                Viewport   0 0
                Depth     1
        EndSubSection
        SubSection "Display"
                Viewport   0 0
                Depth     4
        EndSubSection
        SubSection "Display"
                Viewport   0 0
                Depth     8
        EndSubSection
        SubSection "Display"
                Viewport   0 0
                Depth     15
        EndSubSection
        SubSection "Display"
                Viewport   0 0
                Depth     16
        EndSubSection
        SubSection "Display"
                Viewport   0 0
                Depth     24
        EndSubSection
EndSection
Reply With Quote
  #4   (View Single Post)  
Old 26th February 2012
jggimi's Avatar
jggimi jggimi is online now
More noise than signal
 
Join Date: May 2008
Location: USA
Posts: 3,667
Thanked 214 Times in 189 Posts
Default

I only see vga1 in your dmesg, yet your xorg.conf has two Card<n> Identifiers. I don't understand why there is no vga0 in the dmesg.
Reply With Quote
  #5   (View Single Post)  
Old 26th February 2012
J65nko J65nko is offline
Administrator
 
Join Date: May 2008
Location: Budel - the Netherlands
Posts: 3,141
Thanked 182 Times in 149 Posts
Default

From Section "ServerLayout" delete Screen 1 "Screen1" RightOf "Screen0"

Delete this section:
Code:
Section "Monitor"
        Identifier   "Monitor1"
        VendorName   "Monitor Vendor"
        ModelName    "Monitor Model"
EndSection
And delete the last section:
Code:
Section "Screen"
        Identifier "Screen1"
        Device     "Card1"
        Monitor    "Monitor1"
        SubSection "Display"
                Viewport   0 0
                Depth     1
        EndSubSection
        SubSection "Display"
                Viewport   0 0
                Depth     4
        EndSubSection
        SubSection "Display"
                Viewport   0 0
                Depth     8
        EndSubSection
        SubSection "Display"
                Viewport   0 0
                Depth     15
        EndSubSection
        SubSection "Display"
                Viewport   0 0
                Depth     16
        EndSubSection
        SubSection "Display"
                Viewport   0 0
                Depth     24
        EndSubSection
EndSection
Then retry starting X.
__________________
You don't need to be a genius to debug a pf.conf firewall ruleset, you just need the guts to run tcpdump
Reply With Quote
  #6   (View Single Post)  
Old 27th February 2012
Daffy Daffy is offline
Fdisk Soldier
 
Join Date: Jun 2010
Posts: 73
Thanked 0 Times in 0 Posts
Default

Already done that. X starts, but I get
Code:
> xvinfo
X-Video Extension version 2.2
screen #0
  no adaptors present
In /var/log/Xorg.0.log I have
Code:
...snip...
[3165368.682] (II) Loading extension XVideo
[3165368.682] (II) Loading extension XVideo-MotionCompensation
...snip...
[3165368.697] (--) NV: Found NVIDIA GeForce 9800 GT at 01@00:00:0
[3165368.698] (II) Loading /usr/X11R6/lib/modules/drivers/nv_drv.so
...snip...
and no errors.

I'm wondering why I get the xvideo error.
Reply With Quote
  #7   (View Single Post)  
Old 27th February 2012
adamk adamk is offline
Spam Deminer
 
Join Date: May 2008
Posts: 250
Thanked 5 Times in 8 Posts
Default

Because the 'nv' driver doesn't support Xv on the 9800. It barely provides any acceleration on newer nvidia GPUs..

Adam
Reply With Quote
  #8   (View Single Post)  
Old 27th February 2012
Daffy Daffy is offline
Fdisk Soldier
 
Join Date: Jun 2010
Posts: 73
Thanked 0 Times in 0 Posts
Default

Quote:
Originally Posted by adamk View Post
Because the 'nv' driver doesn't support Xv on the 9800. It barely provides any acceleration on newer nvidia GPUs..

Adam
Thanks! That was the info I was looking for.
So ATi it is.
Reply With Quote
  #9   (View Single Post)  
Old 27th February 2012
adamk adamk is offline
Spam Deminer
 
Join Date: May 2008
Posts: 250
Thanked 5 Times in 8 Posts
Default

Quote:
Originally Posted by Daffy View Post
Thanks! That was the info I was looking for.
So ATi it is.
Make sure it's nothing newer than the HD4950.

Adam
Reply With Quote
Reply

Tags
configure, nvidia, openbsd, xorg

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
configuring second NIC tomp OpenBSD Installation and Upgrading 19 15th August 2011 07:25 PM
It's necesary to use firmware configuring rum or zyd? ximo FreeBSD General 7 8th July 2009 10:05 AM
Help configuring pine cssgalactic FreeBSD General 4 29th June 2008 11:50 PM
Need Help Configuring Postfix iainnitro General software and network 6 8th June 2008 04:55 AM
Configuring VLANs under FreeBSD Popof FreeBSD General 5 13th May 2008 04:08 PM


All times are GMT. The time now is 03:12 PM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Content copyright © 2007-2010, the authors
Daemon image copyright ©1988, Marshall Kirk McKusick