|
OpenBSD Installation and Upgrading Installing and upgrading OpenBSD. |
|
Thread Tools | Display Modes |
|
|||
5.0 Installation work, but hangs on boot
Hi,
I have a strange problem. I will use a Netbook (intellibook Atom 570) with OBSD. The installation of AMD64 or i386 works, but every boot after the installation hangs. These are the last dmsg's: npx0 at ... mtrr: Pentium Pro MTRR support Any ideas what to do? Thanks sabbel |
|
|||
Please post the entire output of dmesg(8).
|
|
|||
dmesg
Thats not so easy, because the system hangs at boot. I wrote this off:
Code:
ichiic0 at pci0 dev 31 function 3 "Intel 82801GB SMBus" rev 0x02: apic 4 int 19 iic0 at ichiic0 spdmem0 at iic0 addr 0x50: 2GB DDR3 SDRAM PC3-10600 SO-DIMM usb1 at uhci0: USB revision 1.0 uhub1 at usb1 "Intel UHCI root hub" rev 1.00/1.00 add 1 usb2 at uhci1: USB revision 1.0 uhub2 at usb2 "Intel UHCI root hub" rev 1.00/1.00 add 1 usb3 at uhci2: USB revision 1.0 uhub3 at usb3 "Intel UHCI root hub" rev 1.00/1.00 add 1 usb4 at uhci3: USB revision 1.0 uhub4 at usb4 "Intel UHCI root hub" rev 1.00/1.00 add 1 isa0 at pcib0 isamda0 at isa0 pckbc0 at isa0 port 0x60/5 pckbd0 at pckbc0 (kbd slot) pckbc0: using irq 1 for kbd slot wskbd0 at pckbd0: console keyboard, using wsdisplay0 pms0 at pckbc0 (aux slot) pckbc0: using irq 12 for aux slot wsmouse0 at pms0 mux 0 pcppi0 at isa0 port 0x61 spkr0 at pcppi0 npx0 at isa0 port 0xf0/16: reported by CPUID: using exception 16 mtrr: Pentium Pro MTRR support Last edited by ocicat; 2nd April 2012 at 05:50 PM. Reason: adding [code]/[/code] tags to make output clear |
|
|||
Would you consider downloading a snapshot of -current, & attempt to install it?
|
|
|||
On my system the next devices that the kernel probes are usb devices
Quote:
|
|
|||
Hi all.
Thank you for your responses! I found in the net that some people have problems with vscsi and pcibios, so I tried to disable this. disable ugen -> no success. I tried with current 5.1 snapshot of 2. April. Sometimes this versions starts a bit more (e.g. until to sshkeygen!), but sometimes it hangs at different points after the mtrr... no complete boot. Argh... |
|
|||
Perhaps it is a problem with the identification of disks? I read something about this in the net. But I can't remove the disk out of the case (only service can open this netbook).
bsd.mp hangs, bsd.sp hangs, only bsd.rd starts (the installation). Last edited by Sabbel; 3rd April 2012 at 08:09 AM. |
|
|||
I have to disable acpi. Now the boot works in 5.0.
|
|
|||
Two questions & a comment:
|
|
|||
Thanks for the hint!
I have send the problem report. This is a Clevo M1110 Netbook, it is relative new (2011?). Here comes the dmesg: Code:
OpenBSD 5.0 (GENERIC.MP) #63: Wed Aug 17 10:14:30 MDT 2011 deraadt@amd64.openbsd.org:/usr/src/s...ile/GENERIC.MP real mem = 2135752704 (2036MB) avail mem = 2064838656 (1969MB) User Kernel Config UKC> disable acpi 333 acpi0 disabled UKC> quit Continuing... mainbus0 at root bios0 at mainbus0: SMBIOS rev. 2.6 @ 0xdc010 (22 entries) bios0: vendor Phoenix Technologies LTD version "6.00" date 03/31/2011 bios0: CLEVO CO. M1110M acpi at bios0 not configured mpbios0 at bios0: Intel MP Specification 1.4 cpu0 at mainbus0: apid 0 (boot processor) cpu0: Intel(R) Atom(TM) CPU N570 @ 1.66GHz, 1662.81 MHz cpu0: FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,SBF,SSE3,MWAIT,DS-CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,MOVBE,NXE,LONG cpu0: 512KB 64b/line 8-way L2 cache cpu0: apic clock running at 166MHz cpu1 at mainbus0: apid 2 (application processor) cpu1: Intel(R) Atom(TM) CPU N570 @ 1.66GHz, 1662.50 MHz cpu1: FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,SBF,SSE3,MWAIT,DS-CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,MOVBE,NXE,LONG cpu1: 512KB 64b/line 8-way L2 cache mpbios0: bus 0 is type PCI mpbios0: bus 19 is type PCI mpbios0: bus 20 is type PCI mpbios0: bus 21 is type ISA ioapic0 at mainbus0: apid 4 pa 0xfec00000, version 20, 24 pins cpu0: unknown Enhanced SpeedStep CPU, msr 0x06130a1c06000a1c cpu0: using only highest and lowest power states cpu0: Enhanced SpeedStep 1662 MHz: speeds: 1667, 1000 MHz pci0 at mainbus0 bus 0 pchb0 at pci0 dev 0 function 0 "Intel Pineview DMI" rev 0x02 vga1 at pci0 dev 2 function 0 "Intel Pineview Video" rev 0x02 wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation) wsdisplay0: screen 1-5 added (80x25, vt100 emulation) intagp0 at vga1 agp0 at intagp0: aperture at 0xd0000000, size 0x10000000 inteldrm0 at vga1: apic 4 int 16 drm0 at inteldrm0 "Intel Pineview Video" rev 0x02 at pci0 dev 2 function 1 not configured azalia0 at pci0 dev 27 function 0 "Intel 82801GB HD Audio" rev 0x02: msi azalia0: codecs: Realtek ALC272 audio0 at azalia0 ppb0 at pci0 dev 28 function 0 "Intel 82801GB PCIE" rev 0x02: msi pci1 at ppb0 bus 19 mem address conflict 0xf0100000/0x4000 "Realtek 8192SE" rev 0x10 at pci1 dev 0 function 0 not configured ppb1 at pci0 dev 28 function 2 "Intel 82801GB PCIE" rev 0x02: msi pci2 at ppb1 bus 20 "JMicron SD/MMC" rev 0x80 at pci2 dev 0 function 0 not configured sdhc0 at pci2 dev 0 function 2 "JMicron SD Host Controller" rev 0x80: can't map interrupt "JMicron Memory Stick" rev 0x80 at pci2 dev 0 function 3 not configured jme0 at pci2 dev 0 function 5 "JMicron JMC260" rev 0x02: apic 4 int 16, address 00:90:f5:bf:72:08 jmphy0 at jme0 phy 1: JMP202 10/100 PHY, rev. 1 uhci0 at pci0 dev 29 function 0 "Intel 82801GB USB" rev 0x02: apic 4 int 23 uhci1 at pci0 dev 29 function 1 "Intel 82801GB USB" rev 0x02: apic 4 int 19 uhci2 at pci0 dev 29 function 2 "Intel 82801GB USB" rev 0x02: apic 4 int 18 uhci3 at pci0 dev 29 function 3 "Intel 82801GB USB" rev 0x02: apic 4 int 16 ehci0 at pci0 dev 29 function 7 "Intel 82801GB USB" rev 0x02: apic 4 int 23 usb0 at ehci0: USB revision 2.0 uhub0 at usb0 "Intel EHCI root hub" rev 2.00/1.00 addr 1 ppb2 at pci0 dev 30 function 0 "Intel 82801BAM Hub-to-PCI" rev 0xe2 pci3 at ppb2 bus 21 pcib0 at pci0 dev 31 function 0 "Intel Tigerpoint LPC" rev 0x02 ahci0 at pci0 dev 31 function 2 "Intel 82801GR AHCI" rev 0x02: msi, AHCI 1.1 scsibus0 at ahci0: 32 targets sd0 at scsibus0 targ 0 lun 0: <ATA, Hitachi HTS54502, PB2O> SCSI3 0/direct fixed naa.5000cca5e8f52342 sd0: 238475MB, 512 bytes/sector, 488397168 sectors ichiic0 at pci0 dev 31 function 3 "Intel 82801GB SMBus" rev 0x02: apic 4 int 19 iic0 at ichiic0 spdmem0 at iic0 addr 0x50: 2GB DDR3 SDRAM PC3-10600 SO-DIMM usb1 at uhci0: USB revision 1.0 uhub1 at usb1 "Intel UHCI root hub" rev 1.00/1.00 addr 1 usb2 at uhci1: USB revision 1.0 uhub2 at usb2 "Intel UHCI root hub" rev 1.00/1.00 addr 1 usb3 at uhci2: USB revision 1.0 uhub3 at usb3 "Intel UHCI root hub" rev 1.00/1.00 addr 1 usb4 at uhci3: USB revision 1.0 uhub4 at usb4 "Intel UHCI root hub" rev 1.00/1.00 addr 1 isa0 at pcib0 isadma0 at isa0 pckbc0 at isa0 port 0x60/5 pckbd0 at pckbc0 (kbd slot) pckbc0: using irq 1 for kbd slot wskbd0 at pckbd0: console keyboard, using wsdisplay0 pms0 at pckbc0 (aux slot) pckbc0: using irq 12 for aux slot wsmouse0 at pms0 mux 0 pcppi0 at isa0 port 0x61 spkr0 at pcppi0 mtrr: Pentium Pro MTRR support vscsi0 at root scsibus1 at vscsi0: 256 targets softraid0 at root scsibus2 at softraid0: 256 targets root on sd0a (681f99f6f2106d68.a) swap on sd0b dump on sd0b Last edited by ocicat; 3rd April 2012 at 03:51 PM. Reason: added [code]/[/code] tags |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
OpenBSD 4.6 i386 boot hangs with old gateway system - resolved | comet--berkeley | OpenBSD Installation and Upgrading | 6 | 22nd July 2011 08:15 AM |
proftpd start at boot wont work | jjjustjjjay | OpenBSD General | 9 | 28th February 2010 12:40 AM |
ln -f at boot doesn't work | lordyan | OpenBSD General | 3 | 19th February 2009 03:50 PM |
openbsd hangs momentarily at boot | bogd | OpenBSD General | 11 | 9th January 2009 02:53 PM |
FreeBSD hangs on boot | Bubba_HoTep | FreeBSD General | 3 | 29th November 2008 10:25 PM |