|
OpenBSD General Other questions regarding OpenBSD which do not fit in any of the categories below. |
|
Thread Tools | Display Modes |
|
|
|||
Connecting to router wirelessly
I recently installed OBSD on my laptop, and I'd like to bring it around the house to use it whenever.
The router has WPA2 for wireless security enabled, because I'm mainly concerned about other people connecting to it or maybe even sniffing packets of the information I'm exchanging with the internet wirelessly. I checked the wireless support section of the Networking documentation on the OBSD website, and I think it said WPA was not supported for ath(4) type wireless cards. (I have a Linksys WPC55AG PCMCIA card.) But I tried to Google some information, and recent posts from 2008 were saying that WPA encryption was functioning on Atheros chip based cards. I'm not sure how to go about this, but first I'd like to confirm whether or not I can use my wireless card as of now. |
|
||||
If you read the -current man page for ath(4), you will see WPA mentioned only in regards to two chipsets that can conduct cryptographic operations, and that the driver does not yet support WPA.
The PCI driver for ath(4) has not been updated in 5 months. The chipset management software for ath(4) was updated several times, approximately four months ago, to add software crypto to support WPA and WPA2. Note that all of these updates are in -current. Since the driver has not been updated, it appears to me that development is not yet complete. |
|
|||
What alternatives would you suggest now if one wanted to surf the web securely over wireless with OBSD?
|
|
||||
|
|
|||
Will it make a difference if my modem and router are one and the same? When my ISP came here to set up internet, they put this giant box in the room (it's bigger than a school binder), which is the modem and also the router, and they told me it was not possible to disable the router even if I wanted to because it was part of the modem or something.
So I'm just wondering if this will make a difference in setting up authpf if I set up another computer for all traffic to be authenticated before using the internet. |
|
|||
This is what my set up looks like right now:
Code:
(Coaxial cable from wall) | [Modem]- antenna / | | \ | | | | [c][c][c][c] The [c]'s are different computers. I can install OpenBSD on any of them. The Modem has a router built into it, and it's not possible to disable it. There is an antenna sticking out of the modem which is the wireless access point. Everything is inside a single box. My research done on WEP made me conclude to believe that it's very easily cracked, which is why I chose WPA2 on the modem/router settings and set my own passkey. Is WEP really safe to use? Last edited by guitarscn; 20th January 2009 at 06:04 PM. |
|
||||
Is WEP sufficient to block inadvertant access by neighbors? Yes.
Is it sufficient to protect your network from the bored 13 year old next door? No. WEP is breakable with simple software. The last time I checked, about 5 years ago, it would take about 15 minutes of sniffing to have enough data to crack 40-bit WEP, and on the order of a couple of hours for 128-bit WEP. But WPA isn't a perfect solution, either. Scan down this page to see the most recent articles on WPA security breaches discussed at Slashdot : http://slashdot.org/search.pl?query=wpa If there is a possibility of a nearby bored teenager, I recommend turning off the Access Point in your router, then have one of your wired platforms run OpenBSD, and insert an OpenBSD-supported access point via USB or PCI, or an ethernet-connected AP via a 2nd NIC. Have this OpenBSD platform be your WiFi router, inside your wired network. e.g.: Code:
{internet} -- [ISP's router, no AP] -- {wired LAN} -- [OpenBSD router with AP] -- {WiFi} Last edited by jggimi; 20th January 2009 at 06:57 PM. |
|
|||
Where can I view a list of all the OpenBSD-supported access point hardware?
For the other option, I'm not really familiar with what an "ethernet-connected access point with a second network card" is. Can you explain what that is? So after I set this up, I can use it like I would a "standard" wireless router and set rules for who can connect to my OpenBSD router and whatnot? |
|
||||
Supported hardware can be found for your architecture starting at www.openbsd.org/plat.html -- but to discover which drivers allow "Host AP" mode, you'll have to click on each individual driver and read through the man page.
An ethernet connected Acess Point is known as a "Wireless Ethernet Bridge" and there are several makes and models, which you can find with a little bit of Google Fu. As far as the wire-connected host is concerned, WiFi connected devices are just MAC and IP addresses reached by a standard Ethernet NIC. |
|
|||
Would you mind if I asked which hardware you use for your wireless setup?
|
|
||||
Sure. My WiFi AP is for home use; it's 802.11b only. The access point is an old Linksys WAP11 wireless ethernet bridge. My OpenBSD laptops use an(4) and wpi(4) NICs.
(On the road with insecure wireless I either use SSH or a VPN, as appropriate.) |
|
|||
I have a Linksys WRT54G router I had before from my previous internet connection before I switched to my current one, and it's being unused since I have the built-in router. Can I make use of the Linksys router?
|
|
||||
A very small amount of Google Fu will show that there is 3rd party firmware which can convert that device into an ethernet bridge. I don't have one, and have not read through any of the links to see what the limitations and capabilities are. I do not even know if you can reverse the process, in order to return it to a working router.
You're certainly welcome to conduct your own research, and make your own tests. |
|
|||
Okay, I'll have to check out those options.
Suppose I set up everything with the OpenBSD router and the wireless access point on it. What prevents other people from connecting to it and using it? |
|
||||
Quote:
It is the standard authentication method for gateway routers using PF. |
|
|||
Oops, sorry, I thought it was a method without using authpf. That was my last question for this topic!
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Connecting to internet via adsl router | michaelrmgreen | FreeBSD General | 3 | 9th August 2009 12:29 PM |
pkgsrc pkg_add problems not connecting | Mr-Biscuit | NetBSD Package System (pkgsrc) | 30 | 14th June 2009 11:28 AM |
pkg_add problems with connecting | Mr-Biscuit | NetBSD Package System (pkgsrc) | 2 | 26th May 2009 11:44 AM |
System freeze when connecting USB flash drive (4.4 & 4.5 but worked in 4.3) | GardenGnome | OpenBSD Installation and Upgrading | 11 | 7th May 2009 02:32 PM |
Connecting to wireless router | TomAmundsen | FreeBSD General | 19 | 25th August 2008 10:14 PM |