|
OpenBSD General Other questions regarding OpenBSD which do not fit in any of the categories below. |
|
Thread Tools | Display Modes |
|
|
|||
X set to use inteldrm but radeondrm is detected, and video is actually Radeon
Well, here goes ...
I have a Dell Optiplex GX620 with 4gb of ram on which I installed OpenBSD6.3 four days ago. There have been no issues with the install except startx: (EE) Fatal server error: (EE) xf86OpenConsole: VT_SETMODE VT_PROCESS failed(EE) (EE) Please consult the The X.Org Foundation support at http://wiki.x.org for help. (EE) Please also check the log file at "/var/log/Xorg.1.log" for additional information. (EE) (EE) Server terminated with error (1). Closing log file. xinit: giving up xinit: unable to connect to X server: Connection refused xinit: server error This is what I got from the Xorg.1.log: (if it's tl;dr, just look at the lines in bold, which I also flagged with ***) [ 91211.455] X.Org ANSI C Emulation: 0.4 [ 91211.455] X.Org Video Driver: 23.0 [ 91211.455] X.Org XInput driver : 24.1 [ 91211.455] X.Org Server Extension : 10.0 [ 91211.455] (--) PCI:*(0:0:2:0) 8086:2772:1028:01ad rev 2, Mem @ 0xfeb00000/524288, 0xe0000000/268435456, 0xfeac0000/262144, I/O @ 0x0000e898/8 [ 91211.455] (--) PCI: (0:0:2:1) 8086:2776:1028:01ad rev 2, Mem @ 0xfeb80000/524288 [ 91211.455] (II) LoadModule: "glx" [ 91211.457] (II) Loading /usr/X11R6/lib/modules/extensions/libglx.so [ 91211.460] (II) Module glx: vendor="X.Org Foundation" [ 91211.460] compiled for 1.19.6, module version = 1.0.0 [ 91211.460] ABI class: X.Org Server Extension, version 10.0 [ 91211.460] (==) Matched intel as autoconfigured driver 0 [ 91211.460] (==) Assigned the driver to the xf86ConfigLayout *** calling your attention to this because I think it's important *** [ 91211.460] (II) LoadModule: "intel" *** note that it says "intel" *** [ 91211.461] (II) Loading /usr/X11R6/lib/modules/drivers/intel_drv.so [ 91211.461] (II) Module intel: vendor="X.Org Foundation" [ 91211.461] compiled for 1.19.6, module version = 2.99.916 [ 91211.461] Module class: X.Org Video Driver [ 91211.461] ABI class: X.Org Video Driver, version 23.0 [ 91211.461] (II) intel: Driver for Intel(R) Integrated Graphics Chipsets: i810, i810-dc100, i810e, i815, i830M, 845G, 854, 852GM/855GM, 865G, 915G, E7221 (i915), 915GM, 945G, 945GM, 945GME, Pineview GM, Pineview G, 965G, G35, 965Q, 946GZ, 965GM, 965GME/GLE, G33, Q35, Q33, GM45, 4 Series, G45/G43, Q45/Q43, G41, B43 [ 91211.462] (II) intel: Driver for Intel(R) HD Graphics: 2000-6000 [ 91211.462] (II) intel: Driver for Intel(R) Iris(TM) Graphics: 5100, 6100 [ 91211.462] (II) intel: Driver for Intel(R) Iris(TM) Pro Graphics: 5200, 6200, P6300 [ 91211.466] (II) intel(0): Using Kernel Mode Setting driver: i915, version 1.6.0 20151010 *** Failure! *** [ 91251.665] (EE) intel(0): [drm] failed to set drm interface version: Permission denied [13]. [ 91251.665] (EE) intel(0): Failed to claim DRM device. [ 91251.665] (II) UnloadModule: "intel" [ 91251.665] (EE) Screen(s) found, but none have a usable configuration. [ 91251.665] (EE) Fatal server error: [ 91251.665] (EE) no screens found(EE) [ 91251.666] (EE) *** End the of failure messages *** Please consult the The X.Org Foundation support at http://wiki.x.org Checking the X confgiuration files at /usr/X11R6/share/X11/xorg.conf.d I find the file 10-radeon.conf which is for Radeon video cards (duh). The contents are: Section "Device" Identifier "Radeon" Driver "radeon" EndSection According to wsconsctl I have: display.type=inteldrm and when I try to use wsconsctl to switch to the the Radeon drm driver (radeondrm or just radeon) I get: display.type is read only The Dell website documentation for the Optiplex GX620 says the video display circuitry is Radeon, usually or always the Sapphire Radeon HD7750. There is no video card. The circuitry is on the motherboard, I believe under the fan/heat sink. (There are no Intel video chips visible anywhere, either.) I am an OpenBSD newbie. I have a bit of FreeBSD experience, but did not use X or any graphical operating system on that box. I spent most of today looking on the Internet for a way to change that 'inteldrm' to 'radeondrm' without success and I've also been through ABSOLUTE OPENBSD. I also searched 'wsconsctl' here on DaemonForums. I even did a VirtualBox install to play around with the settings there,and never found what I needed. Please tell me two things: am I right to think that I need to change 'inteldrm' to 'radeondrm', and if so, how do I do it? |
|
||||
I'm using /etc/xorg.conf to set options for the i915 (Intel) driver so try copying 20-radeon.conf to that location.
Alternatively, set display=radeondrm in /etc/wsconsctl.conf (untested). EDIT: you should post your dmesg output as well.
__________________
Are you infected with Wetiko? Last edited by Head_on_a_Stick; 27th August 2018 at 07:35 AM. |
|
|||
According to this:
https://www.dell.com/downloads/emea/...0_gx520_uk.pdf Quote:
|
Tags |
inteldrm, radeondrm, startx, wsconsctrl |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Inteldrm set / change resolution during boot ? | NaWi | OpenBSD General | 5 | 8th August 2015 11:52 AM |
OpenBSD 5.5 radeon/radeondrm cannot scroll framebuffer | blackhole | OpenBSD General | 4 | 15th September 2014 01:31 PM |
AMD Radeon card compatibility with the DragonFlyBSD Radeon driver. | guitarfreak | Other BSD and UNIX/UNIX-like | 1 | 4th April 2014 01:47 PM |
AMD Radeon cards supported by the Radeon driver for Current/5.5 | guitarfreak | OpenBSD General | 3 | 4th April 2014 12:33 PM |
Memory Not Detected | jrs | OpenBSD Installation and Upgrading | 3 | 19th May 2009 05:50 PM |