|
OpenBSD General Other questions regarding OpenBSD which do not fit in any of the categories below. |
|
Thread Tools | Display Modes |
|
|
|||
Trouble Connecting Laptop With wpi0
Hello,
Can someone please take a look and see what I am doing wrong? I am trying to connect my laptop to my wireless router (which uses wpa2/aes). /etc/hostname.wpi0 Code:
dhcp NONE NONE NONE nwid mynetwork wpa wpapsk mykeygoeshere This is the output of ifconfig wpi0 Code:
wpi0: flags=8803<UP,BROADCAST,SIMPLEX,MULTICAST> mtu 1500 lladdr 00:13:02:23:80:26 priority: 4 groups: wlan media: IEEE802.11 autoselect status: no network ieee80211: nwid mynetwork wpaprotos wpa1,wpa2 wpaakms psk wpaciphers tkip,ccmp wpagroupcipher tkip Code:
OpenBSD 5.2 (GENERIC.MP) #339: Wed Aug 1 10:13:24 MDT 2012 deraadt@i386.openbsd.org:/usr/src/sys/arch/i386/compile/GENERIC.MP cpu0: Genuine Intel(R) CPU T2300 @ 1.66GHz ("GenuineIntel" 686-class) 1.67 GHz cpu0: FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,SBF,NXE,SSE3,MWAIT,VMX,EST,TM2,xTPR,PDCM real mem = 1071706112 (1022MB) avail mem = 1043312640 (994MB) mainbus0 at root bios0 at mainbus0: AT/286+ BIOS, date 09/07/07, BIOS32 rev. 0 @ 0xfd600, SMBIOS rev. 2.4 @ 0xe3810 (17 entries) bios0: vendor Hewlett-Packard version "F.24" date 09/07/2007 bios0: Hewlett-Packard HP Pavilion dv8000 (EU006UA#ABA) acpi0 at bios0: rev 0 acpi0: sleep states S0 S3 S4 S5 acpi0: tables DSDT FACP APIC HPET MCFG BOOT APIC SSDT SSDT acpi0: wakeup devices LANC(S5) PS2K(S3) PS2M(S3) acpitimer0 at acpi0: 3579545 Hz, 24 bits acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat cpu0 at mainbus0: apid 0 (boot processor) cpu0: apic clock running at 166MHz cpu1 at mainbus0: apid 1 (application processor) cpu1: Genuine Intel(R) CPU T2300 @ 1.66GHz ("GenuineIntel" 686-class) 1.67 GHz cpu1: FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,SBF,NXE,SSE3,MWAIT,VMX,EST,TM2,xTPR,PDCM ioapic0 at mainbus0: apid 1 pa 0xfec00000, version 20, 24 pins ioapic0: misconfigured as apic 2, remapped to apid 1 acpihpet0 at acpi0: 14318179 Hz acpimcfg0 at acpi0 addr 0xe0000000, bus 0-255 acpiprt0 at acpi0: bus 0 (PCI0) acpiprt1 at acpi0: bus 1 (PEGP) acpiprt2 at acpi0: bus 2 (RP01) acpiprt3 at acpi0: bus 3 (RP02) acpiprt4 at acpi0: bus 6 (RP03) acpiprt5 at acpi0: bus 8 (PCIB) acpiec0 at acpi0 acpicpu0 at acpi0: C3, C2, C1, PSS acpicpu1 at acpi0: C3, C2, C1, PSS acpitz0 at acpi0: critical temperature is 99 degC acpitz1 at acpi0: critical temperature is 105 degC acpibtn0 at acpi0: LID_ acpibtn1 at acpi0: PWRB acpibat0 at acpi0: BAT1 model "Primary " type Lion oem "Hewlett-Packard " acpiac0 at acpi0: AC unit online acpivideo0 at acpi0: VGA_ acpivout0 at acpivideo0: LCD_ acpivideo1 at acpi0: GFX0 acpivout1 at acpivideo1: LCD_ bios0: ROM list: 0xc0000/0xf000 0xcf000/0x1800 0xe0000/0x1800! 0xe3800/0x800! cpu0: Enhanced SpeedStep 1663 MHz: speeds: 1667, 1333, 1000 MHz pci0 at mainbus0 bus 0: configuration mode 1 (bios) pchb0 at pci0 dev 0 function 0 "Intel 82945GM Host" rev 0x03 ppb0 at pci0 dev 1 function 0 "Intel 82945GM PCIE" rev 0x03: apic 1 int 16 pci1 at ppb0 bus 1 vga1 at pci1 dev 0 function 0 "NVIDIA GeForce 7400 Go" rev 0xa1 wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation) wsdisplay0: screen 1-5 added (80x25, vt100 emulation) azalia0 at pci0 dev 27 function 0 "Intel 82801GB HD Audio" rev 0x01: msi azalia0: codecs: Conexant CX20551 audio0 at azalia0 ppb1 at pci0 dev 28 function 0 "Intel 82801GB PCIE" rev 0x01: apic 1 int 17 pci2 at ppb1 bus 2 ppb2 at pci0 dev 28 function 1 "Intel 82801GB PCIE" rev 0x01: apic 1 int 16 pci3 at ppb2 bus 3 ppb3 at pci0 dev 28 function 2 "Intel 82801GB PCIE" rev 0x01: apic 1 int 18 pci4 at ppb3 bus 6 mem address conflict 0xd2100000/0x1000 wpi0 at pci4 dev 0 function 0 "Intel PRO/Wireless 3945ABG" rev 0x02: msi, MoW1, address 00:13:02:23:80:26 uhci0 at pci0 dev 29 function 0 "Intel 82801GB USB" rev 0x01: apic 1 int 23 uhci1 at pci0 dev 29 function 1 "Intel 82801GB USB" rev 0x01: apic 1 int 19 uhci2 at pci0 dev 29 function 2 "Intel 82801GB USB" rev 0x01: apic 1 int 18 uhci3 at pci0 dev 29 function 3 "Intel 82801GB USB" rev 0x01: apic 1 int 16 ehci0 at pci0 dev 29 function 7 "Intel 82801GB USB" rev 0x01: apic 1 int 23 ehci0: timed out waiting for BIOS usb0 at ehci0: USB revision 2.0 uhub0 at usb0 "Intel EHCI root hub" rev 2.00/1.00 addr 1 ppb4 at pci0 dev 30 function 0 "Intel 82801BAM Hub-to-PCI" rev 0xe1 pci5 at ppb4 bus 8 cbb0 at pci5 dev 6 function 0 "TI PCIXX12 CardBus" rev 0x00: apic 1 int 18 "TI PCIXX12 FireWire" rev 0x00 at pci5 dev 6 function 1 not configured "TI PCIXX12 Multimedia Card Reader" rev 0x00 at pci5 dev 6 function 2 not configured sdhc0 at pci5 dev 6 function 3 "TI PCIXX12 Secure Data" rev 0x00: apic 1 int 20 sdmmc0 at sdhc0 fxp0 at pci5 dev 8 function 0 "Intel PRO/100 VM" rev 0x01, i82562: apic 1 int 20, address 00:0f:b0:ff:6b:1f inphy0 at fxp0 phy 1: i82562ET 10/100 PHY, rev. 0 cardslot0 at cbb0 slot 0 flags 0 cardbus0 at cardslot0: bus 9 device 0 cacheline 0x10, lattimer 0x20 pcmcia0 at cardslot0 ichpcib0 at pci0 dev 31 function 0 "Intel 82801GBM LPC" rev 0x01: PM disabled pciide0 at pci0 dev 31 function 1 "Intel 82801GB IDE" rev 0x01: DMA, channel 0 configured to compatibility, channel 1 configured to compatibility atapiscsi0 at pciide0 channel 0 drive 0 scsibus0 at atapiscsi0: 2 targets cd0 at scsibus0 targ 0 lun 0: <HL-DT-ST, DVDRAM GSA-4084N, KQ09> ATAPI 5/cdrom removable cd0(pciide0:0:0): using PIO mode 4, DMA mode 2 pciide0: channel 1 ignored (disabled) ahci0 at pci0 dev 31 function 2 "Intel 82801GBM AHCI" rev 0x01: msi, AHCI 1.1 scsibus1 at ahci0: 32 targets sd0 at scsibus1 targ 0 lun 0: <ATA, HTS541080G9SA00, MB4O> SCSI3 0/direct fixed t10.ATA_HTS541080G9SA00_MPBDL0X6KJDVXM sd0: 76319MB, 512 bytes/sector, 156301488 sectors sd1 at scsibus1 targ 2 lun 0: <ATA, HTS541080G9SA00, MB4O> SCSI3 0/direct fixed t10.ATA_HTS541080G9SA00_MPBDL0X6KJ4YNM sd1: 76319MB, 512 bytes/sector, 156301488 sectors ichiic0 at pci0 dev 31 function 3 "Intel 82801GB SMBus" rev 0x01: apic 1 int 19 iic0 at ichiic0 spdmem0 at iic0 addr 0x50: 512MB DDR2 SDRAM non-parity PC2-5300CL5 SO-DIMM spdmem1 at iic0 addr 0x52: 512MB DDR2 SDRAM non-parity PC2-5300CL5 SO-DIMM usb1 at uhci0: USB revision 1.0 uhub1 at usb1 "Intel UHCI root hub" rev 1.00/1.00 addr 1 usb2 at uhci1: USB revision 1.0 uhub2 at usb2 "Intel UHCI root hub" rev 1.00/1.00 addr 1 usb3 at uhci2: USB revision 1.0 uhub3 at usb3 "Intel UHCI root hub" rev 1.00/1.00 addr 1 usb4 at uhci3: USB revision 1.0 uhub4 at usb4 "Intel UHCI root hub" rev 1.00/1.00 addr 1 isa0 at ichpcib0 isadma0 at isa0 pckbc0 at isa0 port 0x60/5 pckbd0 at pckbc0 (kbd slot) pckbc0: using irq 1 for kbd slot wskbd0 at pckbd0: console keyboard, using wsdisplay0 pms0 at pckbc0 (aux slot) pckbc0: using irq 12 for aux slot wsmouse0 at pms0 mux 0 pms0: Synaptics touchpad, firmware 6.2 pcppi0 at isa0 port 0x61 spkr0 at pcppi0 npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16 mtrr: Pentium Pro MTRR support vscsi0 at root scsibus2 at vscsi0: 256 targets softraid0 at root scsibus3 at softraid0: 256 targets root on sd0a (b5b6cdf80eb27433.a) swap on sd0b dump on sd0b wpi0: error, 2, could not read firmware wpi-3945abg wpi0: could not read firmware wpi0: error, 2, could not read firmware wpi-3945abg wpi0: could not read firmware wpi0: error, 2, could not read firmware wpi-3945abg wpi0: could not read firmware umass0 at uhub0 port 6 configuration 1 interface 0 " Patriot Memory" rev 2.00/1.00 addr 2 umass0: using SCSI over Bulk-Only scsibus4 at umass0: 2 targets, initiator 0 sd2 at scsibus4 targ 1 lun 0: <, Patriot Memory, PMAP> SCSI0 0/direct removable serial.13fe310006013C489063 sd2: 30528MB, 512 bytes/sector, 62521344 sectors sd2 detached scsibus4 detached umass0 detached umass0 at uhub0 port 1 configuration 1 interface 0 " Patriot Memory" rev 2.00/1.00 addr 2 umass0: using SCSI over Bulk-Only scsibus4 at umass0: 2 targets, initiator 0 sd2 at scsibus4 targ 1 lun 0: <, Patriot Memory, PMAP> SCSI0 0/direct removable serial.13fe310006013C489063 sd2: 30528MB, 512 bytes/sector, 62521344 sectors |
|
|||
Thanks, you have helped me alot on many threads and I appreciate that!
I changed it wpakey (which was one of my problems) which helped but still did not work. So from the dmesg I googled this error message Code:
wpi0: error, 2, could not read firmware wpi-3945abg wpi0: could not read firmware http://firmware.openbsd.org/firmware...rmware-3.2.tgz and used pkg_add to add it (just incase someone else is trying to do this in the future) |
|
||||
Take a look at the fw_update(1) man page. This tool automates firmware acquisition for many devices where their licensing does not permit packaging firmware with the OS.
The RAMDISK kernel's install and upgrade scripts normally set this to run at first boot after install or upgrade. Of course, if you don't have a working network interface on first boot, it won't do much for you. Here's the two lines in /usr/src/distrib/miniroot/install.sub that do this: Code:
update_firmware() { echo "/usr/sbin/fw_update -v" >> /mnt/etc/rc.firsttime |
|
|||
NICE! Thanks again!
|
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
any consequences to moving a laptop-based installed disk to another different laptop | daemonfowl | OpenBSD General | 7 | 2nd August 2012 04:29 PM |
SSH failure when connecting to another machine via X | daemonfowl | OpenBSD Security | 4 | 27th July 2012 03:50 AM |
Lenovo T60 as a wireless AP (wpi0), DHCP server | mbonitat | OpenBSD General | 5 | 30th December 2011 08:25 PM |
Trouble connecting to the internet | sepuku | OpenBSD General | 10 | 25th July 2011 07:05 PM |
Connecting to wireless router | TomAmundsen | FreeBSD General | 19 | 25th August 2008 10:14 PM |