|
OpenBSD General Other questions regarding OpenBSD which do not fit in any of the categories below. |
|
Thread Tools | Display Modes |
|
|
|||
need help to configure netstick.
I need help to configure a netstick (Orange iCON 225 UMTS USB stick).
I use an openbsd operating system. I'd appreciate your help asap and examples are more then welcome. thanks in advance. matthew. |
|
|||
In addition to jggimi's comments, you will find this topic addressed in Section 14.17 of the FAQ.
We highly recommend all users of OpenBSD familiarize themselves with the complete FAQ. Most questions posed to us at this site (including questions posed by you in the past...) are answered in this document. You will save yourself significant time & aggravation by taking time now to study the FAQ. |
|
|||
need help to configure a netstick
This is the detail I received after I ran the command /var/run/dmesg .
Do I need to install DRIVER for the cellualr NETSTICK. Code:
OpenBSD 4.9 (GENERIC) #671: Wed Mar 2 07:09:00 MST 2011 deraadt@i386.openbsd.org:/usr/src/sys/arch/i386/compile/GENERIC cpu0: Geode(TM) Integrated Processor by AMD PCS ("AuthenticAMD" 586-class) 499 M Hz cpu0: FPU,DE,PSE,TSC,MSR,CX8,SEP,PGE,CMOV,CFLUSH,MMX real mem = 268009472 (255MB) avail mem = 253493248 (241MB) mainbus0 at root bios0 at mainbus0: AT/286+ BIOS, date 11/05/08, BIOS32 rev. 0 @ 0xfd088 pcibios0 at bios0: rev 2.1 @ 0xf0000/0x10000 pcibios0: pcibios_get_intr_routing - function not supported pcibios0: PCI IRQ Routing information unavailable. pcibios0: PCI bus #0 is the last bus bios0: ROM list: 0xe0000/0xa800 cpu0 at mainbus0: (uniprocessor) pci0 at mainbus0 bus 0: configuration mode 1 (bios) pchb0 at pci0 dev 1 function 0 "AMD Geode LX" rev 0x33 glxsb0 at pci0 dev 1 function 2 "AMD Geode LX Crypto" rev 0x00: RNG AES vr0 at pci0 dev 9 function 0 "VIA VT6105M RhineIII" rev 0x96: irq 10, address 00 :0d:b9:1c:96:80 ukphy0 at vr0 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI 0x004063, model 0x0034 vr1 at pci0 dev 10 function 0 "VIA VT6105M RhineIII" rev 0x96: irq 11, address 0 0:0d:b9:1c:96:81 ukphy1 at vr1 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI 0x004063, model 0x0034 glxpcib0 at pci0 dev 15 function 0 "AMD CS5536 ISA" rev 0x03: rev 3, 32-bit 3579 545Hz timer, watchdog, gpio gpio0 at glxpcib0: 32 pins pciide0 at pci0 dev 15 function 2 "AMD CS5536 IDE" rev 0x01: DMA, channel 0 wire d to compatibility, channel 1 wired to compatibility wd0 at pciide0 channel 0 drive 0: <CF 4GB> wd0: 1-sector PIO, LBA, 3831MB, 7847280 sectors wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 2 pciide0: channel 1 ignored (disabled) ohci0 at pci0 dev 15 function 4 "AMD CS5536 USB" rev 0x02: irq 12, version 1.0, legacy support ehci0 at pci0 dev 15 function 5 "AMD CS5536 USB" rev 0x02: irq 12 usb0 at ehci0: USB revision 2.0 uhub0 at usb0 "AMD EHCI root hub" rev 2.00/1.00 addr 1 isa0 at glxpcib0 isadma0 at isa0 com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo com0: console com1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo pcppi0 at isa0 port 0x61 spkr0 at pcppi0 npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16 usb1 at ohci0: USB revision 1.0 uhub1 at usb1 "AMD OHCI root hub" rev 1.00/1.00 addr 1 biomask f3e7 netmask ffe7 ttymask ffff mtrr: K6-family MTRR support (2 registers) nvram: invalid checksum umsm0 at uhub1 port 3 configuration 1 interface 0 "Option N.V. Globetrotter HSDP A Modem" rev 1.10/0.00 addr 2 vscsi0 at root scsibus0 at vscsi0: 256 targets softraid0 at root root on wd0a swap on wd0b dump on wd0b clock: unknown CMOS layout umsm0 detached umsm0 at uhub1 port 3 configuration 1 interface 0 "Option N.V. Globetrotter HSDP A Modem" rev 1.10/0.00 addr 2 ucom0 at umsm0 umsm1 at uhub1 port 3 configuration 1 interface 1 "Option N.V. Globetrotter HSDP A Modem" rev 1.10/0.00 addr 2 ucom1 at umsm1 umsm2 at uhub1 port 3 configuration 1 interface 2 "Option N.V. Globetrotter HSDP A Modem" rev 1.10/0.00 addr 2 ucom2 at umsm2 duplicate IP address 192.168.1.102 sent from ethernet address 02:21:6a:ac:a8:e8 duplicate IP address 192.168.1.102 sent from ethernet address 02:21:6a:ac:a8:e8 Last edited by ocicat; 17th October 2011 at 05:03 PM. Reason: Please use [code] & [/code] tags when posting screen output. |
|
||||
There are no add-on drivers for any hardware with OpenBSD. It uses a monolithic kernel.
This is a umsm(4) Qualcomm modem adapter: Code:
umsm0 at uhub1 port 3 configuration 1 interface 0 "Option N.V. Globetrotter HSDP A Modem" rev 1.10/0.00 addr 2 Code:
ucom0 at umsm0 |
|
|||
No, it's clearly being enumerated properly, but you have ucom[0-2], so you'll need to discover which one is accepting AT commands.
You can use cu(1)/tip(1) to send raw commands, ATI should return something on one or more of the devices.. Just in case you're not sure what the device nodes are: /dev/cuaU0 /dev/cuaU1 /dev/cuaU2 Once you've figured that out, you'll need to establish a PPP connection, I don't really know much about these devices. |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
configure dwm in pkgsrc? | queshaw | NetBSD Package System (pkgsrc) | 7 | 10th March 2011 07:15 PM |
How to configure VSFTPD? | Sunsawe | FreeBSD Ports and Packages | 8 | 26th September 2009 02:28 PM |
how to configure ipfw with 4 modems??? | m4st3rcr4zy | FreeBSD General | 0 | 13th February 2009 06:26 AM |
configure iwi0 | milo974 | OpenBSD General | 1 | 4th August 2008 12:27 PM |
Ath0 + wpa, how configure? | nesca2in1 | FreeBSD General | 10 | 2nd July 2008 04:12 AM |