Network configuration for a USB broadband device

[PapaParrot]

I am having trouble understanding what I read in search results, and also the manual, in
relation to setting up or starting a network connection, using a USB broadband device.
With OpenBsd on a VM, I had no problems, but that mostly because I had a active connection, and via the VM it found the connection.
Now, I have installed OpenBsd to a USB drive,16gb,. it boots fine, all the sets are installed,
but setting up the "network" is a real mystery to me, always had "networkmanager" to help,
so now I am kind of lost on this, every time I get a chance I have been searching for instructions, and info, I did find sort of a example, just this evening, but have not tried it yet.
It is "reading" the broad band device,..I can see that in my dmesg , here it is:

 OpenBSD 5.7 (GENERIC.MP) #767: Sun Mar  8 11:04:48 MDT 2015
    deraadt@i386.openbsd.org:/usr/src/sys/arch/i386/compile/GENERIC.MP
RTC BIOS diagnostic error 80<clock_battery>
cpu0: Intel(R) Core(TM) i3 CPU M 350 @ 2.27GHz ("GenuineIntel" 686-class) 2.27 GHz
cpu0: FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,NXE,LONG,SSE3,DTES64,MWAIT,DS-CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,SSE4.1,SSE4.2,POPCNT,LAHF,PERF,ITSC
real mem  = 2606501888 (2485MB)
avail mem = 2551525376 (2433MB)
mpath0 at root
scsibus0 at mpath0: 256 targets
mainbus0 at root
bios0 at mainbus0: date 11/07/11, SMBIOS rev. 2.6 @ 0xe9500 (32 entries)
bios0: vendor Hewlett-Packard version "F.29" date 11/07/2011
bios0: Hewlett-Packard HP Pavilion dv6 Notebook PC
acpi0 at bios0: rev 2
acpi0: sleep states S0 S3 S4 S5
acpi0: tables DSDT FACP ASF! HPET APIC MCFG SLIC BOOT ASPT WDAT SSDT
acpi0: wakeup devices P0P2(S4) PEGP(S4) P0P3(S4) PEGP(S4) P0P1(S4) PS2K(S3) PS2M(S3) EHC1(S0) USB1(S0) USB2(S0) USB3(S0) USB4(S0) EHC2(S0) USB5(S0) USB6(S0) USB7(S0) [...]
acpitimer0 at acpi0: 3579545 Hz, 24 bits
acpihpet0 at acpi0: 14318179 Hz
acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat
cpu0 at mainbus0: apid 0 (boot processor)
mtrr: Pentium Pro MTRR support, 8 var ranges, 88 fixed ranges
cpu0: apic clock running at 133MHz
cpu0: mwait min=64, max=64, C-substates=0.2.1.1.0, IBE
cpu1 at mainbus0: apid 1 (application processor)
cpu1: Intel(R) Core(TM) i3 CPU M 350 @ 2.27GHz ("GenuineIntel" 686-class) 2.27 GHz
cpu1: FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,NXE,LONG,SSE3,DTES64,MWAIT,DS-CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,SSE4.1,SSE4.2,POPCNT,LAHF,PERF,ITSC
cpu2 at mainbus0: apid 4 (application processor)
cpu2: Intel(R) Core(TM) i3 CPU M 350 @ 2.27GHz ("GenuineIntel" 686-class) 2.27 GHz
cpu2: FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,NXE,LONG,SSE3,DTES64,MWAIT,DS-CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,SSE4.1,SSE4.2,POPCNT,LAHF,PERF,ITSC
cpu3 at mainbus0: apid 5 (application processor)
cpu3: Intel(R) Core(TM) i3 CPU M 350 @ 2.27GHz ("GenuineIntel" 686-class) 2.27 GHz
cpu3: FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,NXE,LONG,SSE3,DTES64,MWAIT,DS-CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,SSE4.1,SSE4.2,POPCNT,LAHF,PERF,ITSC
ioapic0 at mainbus0: apid 2 pa 0xfec00000, version 20, 24 pins
ioapic0: misconfigured as apic 0, remapped to apid 2
acpimcfg0 at acpi0 addr 0xf0000000, bus 0-127
acpiprt0 at acpi0: bus 0 (PCI0)
acpiprt1 at acpi0: bus -1 (P0P2)
acpiprt2 at acpi0: bus -1 (P0P3)
acpiprt3 at acpi0: bus 4 (P0P1)
acpiprt4 at acpi0: bus 2 (RP01)
acpiprt5 at acpi0: bus 3 (RP02)
acpiprt6 at acpi0: bus -1 (RP03)
acpiec0 at acpi0### AML PARSE ERROR (0xe20e): Undefined name: \\_PR_.CPU0._PPC
error evaluating: \\_SB_.PCI0.LPCB.EC0_._REG
acpiec _REG failed, broken BIOS

acpicpu0 at acpi0: C3, C1, PSS
acpicpu1 at acpi0: C3, C1, PSS
acpicpu2 at acpi0: C3, C1, PSS
acpicpu3 at acpi0: C3, C1, PSS
acpitz0 at acpi0acpitz0: TZ01: failed to read _CRT
acpitz0: TZ01: failed to read _CRT
: no critical temperature defined
acpibtn0 at acpi0: PWRB
acpibtn1 at acpi0: LID0
acpiac0 at acpi0: AC unit online
acpibat0 at acpi0: BAT0 model "Primary" serial   type LION oem "Hewlett-Packard"
acpivideo0 at acpi0: GFX0
acpivout0 at acpivideo0: DD02
acpivideo1 at acpi0: VGA_
acpivideo2 at acpi0: VGA_
bios0: ROM list: 0xc0000/0xee00 0xcf000/0x2c00!
cpu0: Enhanced SpeedStep 2262 MHz: speeds: 2266, 2133, 1999, 1866, 1733, 1599, 1466, 1333, 1199, 1066, 933 MHz
pci0 at mainbus0 bus 0: configuration mode 1 (bios)
pchb0 at pci0 dev 0 function 0 "Intel Core Host" rev 0x02
vga1 at pci0 dev 2 function 0 "Intel HD Graphics" rev 0x02
intagp0 at vga1
agp0 at intagp0: aperture at 0xa0000000, size 0x10000000
inteldrm0 at vga1
drm0 at inteldrm0
inteldrm0: 1366x768
wsdisplay0 at vga1 mux 1: console (std, vt100 emulation)
wsdisplay0: screen 1-5 added (std, vt100 emulation)
"Intel 3400 MEI" rev 0x06 at pci0 dev 22 function 0 not configured
ehci0 at pci0 dev 26 function 0 "Intel 3400 USB" rev 0x05: apic 2 int 16
usb0 at ehci0: USB revision 2.0
uhub0 at usb0 "Intel EHCI root hub" rev 2.00/1.00 addr 1
azalia0 at pci0 dev 27 function 0 "Intel 3400 HD Audio" rev 0x05: msi
azalia0: codecs: IDT 92HD81B1X, Intel/0x2804, using IDT 92HD81B1X
audio0 at azalia0
ppb0 at pci0 dev 28 function 0 "Intel 3400 PCIE" rev 0x05: apic 2 int 17
pci1 at ppb0 bus 2
"Broadcom BCM4313" rev 0x01 at pci1 dev 0 function 0 not configured
ppb1 at pci0 dev 28 function 1 "Intel 3400 PCIE" rev 0x05: apic 2 int 16
pci2 at ppb1 bus 3
3:0:0: mem address conflict 0xffff0000/0x10000
re0 at pci2 dev 0 function 0 "Realtek 8168" rev 0x03: RTL8168D/8111D (0x2800), msi, address 60:eb:69:0f:9b:26
rgephy0 at re0 phy 7: RTL8169S/8110S PHY, rev. 2
ehci1 at pci0 dev 29 function 0 "Intel 3400 USB" rev 0x05: apic 2 int 21
usb1 at ehci1: USB revision 2.0
uhub1 at usb1 "Intel EHCI root hub" rev 2.00/1.00 addr 1
ppb2 at pci0 dev 30 function 0 "Intel 82801BAM Hub-to-PCI" rev 0xa5
pci3 at ppb2 bus 4
pcib0 at pci0 dev 31 function 0 "Intel HM55 LPC" rev 0x05
ahci0 at pci0 dev 31 function 2 "Intel 3400 AHCI" rev 0x05: msi, AHCI 1.3
scsibus1 at ahci0: 32 targets
sd0 at scsibus1 targ 0 lun 0: <ATA, ST9500325AS, 0005> SCSI3 0/direct fixed naa.5000c50027da2062
sd0: 476940MB, 512 bytes/sector, 976773168 sectors
cd0 at scsibus1 targ 1 lun 0: <hp, CDDVDW TS-L633N, 0300> ATAPI 5/cdrom removable
ichiic0 at pci0 dev 31 function 3 "Intel 3400 SMBus" rev 0x05: apic 2 int 19
iic0 at ichiic0
lisa0 at iic0 addr 0x1c: lis331dl
spdmem0 at iic0 addr 0x50: 2GB DDR3 SDRAM PC3-10600 SO-DIMM
spdmem1 at iic0 addr 0x52: 2GB DDR3 SDRAM PC3-10600 SO-DIMM
itherm0 at pci0 dev 31 function 6 "Intel 3400 Thermal" rev 0x05
isa0 at pcib0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pms0 at pckbc0 (aux slot)
pckbc0: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
pms0: Synaptics clickpad, firmware 7.4
pcppi0 at isa0 port 0x61
spkr0 at pcppi0
npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
pci4 at mainbus0 bus 127
pchb1 at pci4 dev 0 function 0 "Intel QuickPath" rev 0x02
pchb2 at pci4 dev 0 function 1 "Intel QuickPath" rev 0x02
pchb3 at pci4 dev 2 function 0 "Intel QPI Link" rev 0x02
pchb4 at pci4 dev 2 function 1 "Intel QPI Physical" rev 0x02
pchb5 at pci4 dev 2 function 2 "Intel Reserved" rev 0x02
pchb6 at pci4 dev 2 function 3 "Intel Reserved" rev 0x02
uhub2 at uhub0 port 1 "Intel Rate Matching Hub" rev 2.00/0.00 addr 2
umass0 at uhub2 port 2 configuration 1 interface 0 "Kingston DataTraveler 2.0" rev 2.00/1.00 addr 3
umass0: using SCSI over Bulk-Only
scsibus2 at umass0: 2 targets, initiator 0
sd1 at scsibus2 targ 1 lun 0: <Kingston, DataTraveler 2.0, PMAP> SCSI2 0/direct removable serial.09306545EF11DA139F15
sd1: 14891MB, 512 bytes/sector, 30497664 sectors
umsm0 at uhub2 port 4 configuration 1 interface 0 "HUAWEI Technology HUAWEI Mobile" rev 2.00/0.00 addr 4
ucom0 at umsm0
umsm1 at uhub2 port 4 configuration 1 interface 1 "HUAWEI Technology HUAWEI Mobile" rev 2.00/0.00 addr 4
ucom1 at umsm1
umsm2 at uhub2 port 4 configuration 1 interface 2 "HUAWEI Technology HUAWEI Mobile" rev 2.00/0.00 addr 4
ucom2 at umsm2
umsm3 at uhub2 port 4 configuration 1 interface 3 "HUAWEI Technology HUAWEI Mobile" rev 2.00/0.00 addr 4
uhub3 at uhub1 port 1 "Intel Rate Matching Hub" rev 2.00/0.00 addr 2
umass1 at uhub3 port 1 configuration 1 interface 0 "ADATA ADATA USB Flash Drive" rev 2.00/1.00 addr 3
umass1: using SCSI over Bulk-Only
scsibus3 at umass1: 2 targets, initiator 0
sd2 at scsibus3 targ 1 lun 0: <ADATA, USB Flash Drive, 0.00> SCSI4 0/direct removable serial.125fcb20917232150003
sd2: 7316MB, 512 bytes/sector, 14984192 sectors
uvideo0 at uhub3 port 5 configuration 1 interface 0 "Realtek 2SF022" rev 2.00/0.08 addr 4
video0 at uvideo0
vscsi0 at root
scsibus4 at vscsi0: 256 targets
softraid0 at root
scsibus5 at softraid0: 256 targets
root on sd1a (fa6ea5061088264e.a) swap on sd1b dump on sd1b

That is pretty long, dmesg | tail , did not have the info needed.
but this is the broad band device:

 umsm0 at uhub2 port 4 configuration 1 interface 0 "HUAWEI Technology HUAWEI Mobile" rev 2.00/0.00 addr 4
ucom0 at umsm0
umsm1 at uhub2 port 4 configuration 1 interface 1 "HUAWEI Technology HUAWEI Mobile" rev 2.00/0.00 addr 4
ucom1 at umsm1
umsm2 at uhub2 port 4 configuration 1 interface 2 "HUAWEI Technology HUAWEI Mobile" rev 2.00/0.00 addr 4
ucom2 at umsm2
umsm3 at uhub2 port 4 configuration 1 interface 3 "HUAWEI Technology HUAWEI Mobile" rev 2.00/0.00 addr 4

------------------------------
These are the example I saw, and sort of some notes I tried to make, but
most of it makes no sense to me,..

---------------------
# my wifi device
auto wlan0
iface wlan0 inet dhcp
        wireless-essid [ESSID]
        wireless-mode [MODE]
-----------------------------
 /etc/network/interfaces
-----------------------------
wpa_supplicant
-----------------
/etc/ppp/cingular-chat:
TIMEOUT 10 
  REPORT CONNECT 
ABORT BUSY 
ABORT 'NO CARRIER' 
ABORT ERROR 
'' ATZ OK AT&F OK 
AT+CGDCONT=1,"IP","isp.cingular" OK 
ATD*99***1# CONNECT
/etc/ppp/peers/ac875:
cuaU0 
115200 
debug 
noauth 
nocrtscts 
:10.254.254.1 
ipcp-accept-remote 
defaultroute 
user isp@cingulargprs.com 
demand 
active-filter 'not udp port 123' 
persist 
idle 600 
connect "/usr/sbin/chat -v -f /etc/ppp/cingular-chat"

Since my ISP is not "cingular", it is "telcel" they do not show a "user" but it says
Number :*99# (that is similar to the cingular, I wonder if I need the
"username" (webgprs)
APN: internet.telcel.com
-------------------------------
I am under the impression I go to:
/etc/network/interfaces and look for, wpa_supplicant, and put the "data" there ? Something
like that, Not sure and confused,..so if anyone has set up their network to use a USB broadband device, any help will be appreciated. The wifi info is not of much use to me, there is no wifi available in this area,..
Ok well for now that is about it, if any other info is needed, let me know what info is needed, and if I don't know how to get that info, I will try asking the "startpage.com" search or just ask here,..I really do hate to be a bother, and have to ask about this,
usually I can figure things out on my own,eventually, but it is nice if and when there is some
one that knows, and can explain,
so anyway, thank you in advance.