|
OpenBSD General Other questions regarding OpenBSD which do not fit in any of the categories below. |
|
Thread Tools | Display Modes |
|
|||
static ip's not showing up in routing table
so i'm running openbsd 4.6 with pf,snort as a gateway. all my interfaces are set up for static ip, everything works fine. Though when i look at routing table the ip's dont appear. Confused to why this is.
|
|
|||
Please show us the output of ifconfig -A and netstat -rn -f inet.
__________________
You don't need to be a genius to debug a pf.conf firewall ruleset, you just need the guts to run tcpdump |
|
|||
Code:
# ifconfig -A lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 33200 priority: 0 groups: lo inet 127.0.0.1 netmask 0xff000000 inet6 ::1 prefixlen 128 inet6 fe80::1%lo0 prefixlen 64 scopeid 0x5 ral0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500 lladdr 00:1d:6a:3a:48:66 priority: 4 groups: wlan media: IEEE802.11 autoselect mode 11g hostap status: active ieee80211: nwid Inland_Empire chan 10 bssid 00:1d:6a:3a:48:66 inet 192.168.1.1 netmask 0xffffff00 broadcast 192.168.1.255 inet6 fe80::21d:6aff:fe3a:4866%ral0 prefixlen 64 scopeid 0x1 re0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500 lladdr 00:18:e7:18:3d:34 priority: 0 media: Ethernet autoselect (100baseTX full-duplex,rxpause,txpause) status: active inet 192.168.0.1 netmask 0xffffff00 broadcast 192.168.0.255 inet6 fe80::218:e7ff:fe18:3d34%re0 prefixlen 64 scopeid 0x2 em0: flags=8b43<UP,BROADCAST,RUNNING,PROMISC,ALLMULTI,SIMPLEX,MULTICAST> mtu 1500 lladdr 00:0d:60:47:d3:9c priority: 0 groups: egress media: Ethernet autoselect (100baseTX full-duplex,rxpause,txpause) status: active inet6 fe80::20d:60ff:fe47:d39c%em0 prefixlen 64 scopeid 0x3 inet 70.64.72.16 netmask 0xfffffc00 broadcast 255.255.255.255 enc0: flags=0<> mtu 1536 priority: 0 pflog0: flags=141<UP,RUNNING,PROMISC> mtu 33200 priority: 0 groups: pflog Code:
# netstat -rn -f inet Routing tables Internet: Destination Gateway Flags Refs Use Mtu Prio Iface default 70.64.72.1 UGS 0 173 - 8 em0 70.64.72/22 link#3 UC 1 0 - 4 em0 70.64.72.1 00:30:b8:c5:05:40 UHLc 1 0 - 4 em0 70.64.72.16 127.0.0.1 UGHS 0 0 33200 8 lo0 127/8 127.0.0.1 UGRS 0 0 33200 8 lo0 127.0.0.1 127.0.0.1 UH 2 0 33200 4 lo0 192.168.0/24 link#2 UC 1 0 - 4 re0 192.168.0.10 00:24:8c:b9:1d:e4 UHLc 1 269 - 4 re0 192.168.1/24 link#1 UC 0 0 - 4 ral0 224/4 127.0.0.1 URS 0 0 33200 8 lo0 |
|
|||
I see several IP's but indeed they don't seem to match the ifconfig ones exactly
Code:
# netstat -rn -f inet Routing tables Internet: Destination Gateway Flags Refs Use Mtu Prio Iface default 70.64.72.1 UGS 0 173 - 8 em0 70.64.72/22 link#3 UC 1 0 - 4 em0 70.64.72.1 00:30:b8:c5:05:40 UHLc 1 0 - 4 em0 70.64.72.16 127.0.0.1 UGHS 0 0 33200 8 lo0 127/8 127.0.0.1 UGRS 0 0 33200 8 lo0 127.0.0.1 127.0.0.1 UH 2 0 33200 4 lo0 192.168.0/24 link#2 UC 1 0 - 4 re0 192.168.0.10 00:24:8c:b9:1d:e4 UHLc 1 269 - 4 re0 192.168.1/24 link#1 UC 0 0 - 4 ral0 224/4 127.0.0.1 URS 0 0 33200 8 lo0
__________________
You don't need to be a genius to debug a pf.conf firewall ruleset, you just need the guts to run tcpdump |
|
|||
snort just listens in on my external interface and modifies pf
yeh the 192.168.0.10 is my wired interface connected to my gw/firewall but what its not showing is 192.168.1.15 and 192.168.1.12 which are 2 of my netbooks that are fully connected to the network and am able to do everything i usually do |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
snd_emu10k1 and static | kly | FreeBSD General | 3 | 17th September 2009 01:28 PM |
I think I just mangled my partition table | Mantazz | FreeBSD Installation and Upgrading | 2 | 2nd July 2009 09:55 PM |
Static IP address problem | rex | FreeBSD General | 2 | 25th November 2008 08:53 PM |
Cannot assign static IP. | bsdnewbie999 | OpenBSD General | 5 | 21st June 2008 09:50 AM |
dhcpd problems... dynamic and static leases present | edhunter | FreeBSD General | 7 | 16th May 2008 02:34 PM |