|
OpenBSD General Other questions regarding OpenBSD which do not fit in any of the categories below. |
|
Thread Tools | Display Modes |
|
|||
Then it is probably driver issue, update OpenBSD to latest stable and try again ...
For me 4.1 for example had panic when ifconfig -M on rum0 interface. |
|
|||
Ok! Thanks!
I will update my OpenBSD 42 to stable
__________________
Please, correct my english if i make mistake ! |
|
|||
Quote:
http://openbsd.org/faq/faq5.html#Flavors Likewise, there have been no changes to /src/sys/dev/pci/if_iwi.c since last November: http://www.openbsd.org/cgi-bin/cvswe...v/pci/if_iwi.c So, upgrading from 4.3-release to either 4.3-stable or 4.3-current in this case will not change the behaviour seen in 4.3-release. Last edited by ocicat; 31st May 2008 at 08:08 AM. |
|
|||
Quote:
Quote:
|
|
|||
OpenBSD 43 didn't install. I can't see the problems (i think, it from bios).
__________________
Please, correct my english if i make mistake ! |
|
|||
May be, i should try install driver from openbsd 43 on openbsd 42 ?
__________________
Please, correct my english if i make mistake ! |
|
|||
This is not advisable.
|
|
|||
I install openbsd 43 and reboot.
I see loader, press "Enter" , then i see some lines and systems reboot. It was so fast , that i cant catch error (i cant see error)
__________________
Please, correct my english if i make mistake ! |
|
|||
Oh, I think we have same problem with 4.3 RELEASE.
On my laptop it reboted because of ACPI issue, so if you disable ACPI (it is explained in documentation) it should be fine. |
|
|||
Yes!
i disabled : boot -c disable biospci ; and other but openbsd 43 not boot!!!
__________________
Please, correct my english if i make mistake ! |
|
|||
I update OpenBSD 42 to OpenBSD 43 (release).
ifconfig iwi0 chan 6 mediaopt monitor ; But ifcconfig iwi0 --- says that chan is 65535 Now, i will update OpenBSD 43 (release) to stable(or current).
__________________
Please, correct my english if i make mistake ! |
|
|||
i see "dmesg |grep iwi"
iwi0:could not load boot firmware iwi0:timeout waiting for master iwi0:iwi0 at pci2 dev 4 function 0 "Intel PRO/Wireless 2200BG" rev 0x05: irq 11, address 00:0e:35:ed:98:b8 I do: ifconfig iwi0 chan 6 mediaopt monitor up ; and sometimes dmseg shows iwi0:could not load boot firmware iwi0:timeout waiting for master iwi0:iwi0 at pci2 dev 4 function 0 "Intel PRO/Wireless 2200BG" rev 0x05: irq 11, address 00:0e:35:ed:98:b8 iwi0:could not load boot firmware iwi0:timeout waiting for master and iwi0 --> down
__________________
Please, correct my english if i make mistake ! |
|
|||
>You are missing iwi firmware from /etc/firmware. Re-install it, per iwi(4).
Ok. iwi0:iwi0 at pci2 dev 4 function 0 "Intel PRO/Wireless 2200BG" rev 0x05: irq 11, address 00:0e:35:ed:98:b8 iwi0:timeout processing cb iwi0:could not load boot firmware iwi0:timeout waiting for master I think, i should buy new notebook or pcmci card . (or other head )
__________________
Please, correct my english if i make mistake ! Last edited by buba; 4th June 2008 at 11:06 AM. |
|
||||
I will give you the same advice I gave leanardz here. If you are sure you have the appropriate files in /etc/firmware, you can report your trouble to the OpenBSD project. Follow ocicat's link in that thread for advice on how to report a problem.
|
|
|||
Oh, no !
pkg_add -v iwi-firmware-3.0.tgz Warning: obsolete construct: "@ignore" Not "@arch i386"
__________________
Please, correct my english if i make mistake ! |
|
||||
As I described to leonardz in this post, you can unpack the tarball and move the files in ./etc/firmware to /etc/firmware.
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
configure iwi0 | milo974 | OpenBSD General | 1 | 4th August 2008 12:27 PM |
dhclient iwi0 "Could not read iwi-bss' error | FreeMan | OpenBSD General | 2 | 15th May 2008 08:01 PM |