Lower Load Cycle Count of a TOSHIBA MQ02ABF100 ?

NaWi · #1 **(View Single Post)** 28th October 2015

Hello !

I have here a TOSHIBA MQ02ABF100 1 TB harddisc which produces round 45 Load Cycle Counts per hour (tried over a time of round 3 hours where the machine was not used). Is this normal or is there a way to reduce it ? I also found no information for a firmware update / upgrade (the drive was bought some months ago).

# atactl sd0

Code:

Model: TOSHIBA MQ02ABF100, Rev: DS001A, Serial #:            75BAW5SPT
Device type: ATA, fixed
Cylinders: 16383, heads: 16, sec/track: 63, total sectors: 1953525168
Device capabilities:
        ATA standby timer values
        IORDY operation
        IORDY disabling
Device supports the following standards:
ATA-3 ATA-4 ATA-5 ATA-6 ATA-7 ATA-8 
Master password revision code 0xfffe
Device supports the following command sets:
        NOP command
        READ BUFFER command
        WRITE BUFFER command
        Host Protected Area feature set
        Read look-ahead
        Write cache
        Power Management feature set
        Security Mode feature set
        SMART feature set
        Flush Cache Ext command
        Flush Cache command
        Device Configuration Overlay feature set
        48bit address feature set
        Set Max security extension commands
        Set Features subcommand required
        Power-up in standby feature set
        Advanced Power Management feature set
        DOWNLOAD MICROCODE command
        IDLE IMMEDIATE with UNLOAD FEATURE
        SMART self-test
        SMART error logging
Device has enabled the following command sets/features:
        NOP command
        READ BUFFER command
        WRITE BUFFER command
        Host Protected Area feature set
        Read look-ahead
        Write cache
        Power Management feature set
        SMART feature set
        Flush Cache Ext command
        Flush Cache command
        Device Configuration Overlay feature set
        48bit address feature set
        Set Features subcommand required
        Advanced Power Management feature set
        DOWNLOAD MICROCODE command

# atactl sd0 readattr

Code:

Attributes table revision: 16
ID      Attribute name                  Threshold       Value   Raw
  1     Raw Read Error Rate               50            100     0x000000000000
  2     Throughput Performance            50            100     0x000000000000
  3     Spin Up Time                       1            100     0x0000000006c3
  4     Start/Stop Count                   0            100     0x0000000000bf
  5     Reallocated Sector Count          50            100     0x000000000000
  7     Seek Error Rate                   50            100     0x000000000000
  8     Seek Time Performance             50            100     0x000000000000
  9     Power-On Hours Count               0             99     0x0000000001b5
 10     Spin Retry Count                  30            103     0x000000000000
 12     Device Power Cycle Count           0            100     0x000000000097
191     G-Sense Error Rate                 0            100     0x000000000000
192     Power-Off Retract Count            0            100     0x00000000000e
193     Load Cycle Count                   0            100     0x00000000196b
194     Temperature                        0            100     0x003400180026
196     Reallocation Event Count           0            100     0x000000000000
197     Current Pending Sector Count       0            100     0x000000000000
198     Off-Line Scan Uncorrectable Sect   0            100     0x000000000000
199     Ultra DMA CRC Error Count          0            200     0x000000000000
220     Disk Shift                         0            100     0x000000000000
222     Loaded Hours                       0            100     0x0000000000de
223     Load/Unload Retry Count            0            100     0x000000000000
224     Load Friction                      0            100     0x000000000000
226     Load-In Time                       0            100     0x000000000108
240     Head Flying Hours                  1            100     0x000000000000

dmesg :

Code:

OpenBSD 5.8-current (GENERIC.MP) #1537: Tue Oct 20 09:44:09 MDT 2015
    deraadt@amd64.openbsd.org:/usr/src/sys/arch/amd64/compile/GENERIC.MP
RTC BIOS diagnostic error f<fixed_disk,invalid_time>
real mem = 7970746368 (7601MB)
avail mem = 7725047808 (7367MB)
mpath0 at root
scsibus0 at mpath0: 256 targets
mainbus0 at root
bios0 at mainbus0: SMBIOS rev. 2.8 @ 0xebd30 (52 entries)
bios0: vendor American Megatrends Inc. version "1.11  x64" date 08/26/2014
bios0: Shuttle Inc. XS35V4
acpi0 at bios0: rev 2
acpi0: sleep states S0 S3 S4 S5
acpi0: tables DSDT FACP APIC FPDT MCFG LPIT SLIC HPET SSDT SSDT SSDT UEFI
acpi0: wakeup devices UAR5(S4) UAR8(S4) XHC1(S4) EHC1(S4) PXSX(S4) PXSX(S4) RLAN(S5) PXSX(S4) PXSX(S4) PWRB(S0)
acpitimer0 at acpi0: 3579545 Hz, 24 bits
acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat
cpu0 at mainbus0: apid 0 (boot processor)
cpu0: Intel(R) Celeron(R) CPU J1900 @ 1.99GHz, 2000.37 MHz
cpu0: FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,PCLMUL,DTES64,MWAIT,DS-CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,SSE4.1,SSE4.2,MOVBE,POPCNT,DEADLINE,RDRAND,NXE,LONG,LAHF,3DNOWP,PERF,ITSC,SMEP,ERMS,SENSOR,ARAT
cpu0: 1MB 64b/line 16-way L2 cache
cpu0: smt 0, core 0, package 0
mtrr: Pentium Pro MTRR support, 8 var ranges, 88 fixed ranges
cpu0: apic clock running at 83MHz
cpu0: mwait min=64, max=64, C-substates=0.2.0.0.0.0.3.3, IBE
cpu1 at mainbus0: apid 2 (application processor)
cpu1: Intel(R) Celeron(R) CPU J1900 @ 1.99GHz, 1999.99 MHz
cpu1: FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,PCLMUL,DTES64,MWAIT,DS-CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,SSE4.1,SSE4.2,MOVBE,POPCNT,DEADLINE,RDRAND,NXE,LONG,LAHF,3DNOWP,PERF,ITSC,SMEP,ERMS,SENSOR,ARAT
cpu1: 1MB 64b/line 16-way L2 cache
cpu1: smt 0, core 1, package 0
cpu2 at mainbus0: apid 4 (application processor)
cpu2: Intel(R) Celeron(R) CPU J1900 @ 1.99GHz, 1999.99 MHz
cpu2: FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,PCLMUL,DTES64,MWAIT,DS-CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,SSE4.1,SSE4.2,MOVBE,POPCNT,DEADLINE,RDRAND,NXE,LONG,LAHF,3DNOWP,PERF,ITSC,SMEP,ERMS,SENSOR,ARAT
cpu2: 1MB 64b/line 16-way L2 cache
cpu2: smt 0, core 2, package 0
cpu3 at mainbus0: apid 6 (application processor)
cpu3: Intel(R) Celeron(R) CPU J1900 @ 1.99GHz, 1999.99 MHz
cpu3: FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,PCLMUL,DTES64,MWAIT,DS-CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,SSE4.1,SSE4.2,MOVBE,POPCNT,DEADLINE,RDRAND,NXE,LONG,LAHF,3DNOWP,PERF,ITSC,SMEP,ERMS,SENSOR,ARAT
cpu3: 1MB 64b/line 16-way L2 cache
cpu3: smt 0, core 3, package 0
ioapic0 at mainbus0: apid 1 pa 0xfec00000, version 20, 87 pins
acpimadt0: bogus nmi for apid 0
acpimadt0: bogus nmi for apid 2
acpimadt0: bogus nmi for apid 4
acpimadt0: bogus nmi for apid 6
acpimcfg0 at acpi0 addr 0xe0000000, bus 0-255
acpihpet0 at acpi0: 14318179 Hz
acpiprt0 at acpi0: bus 0 (PCI0)
acpiprt1 at acpi0: bus 1 (RP01)
acpiprt2 at acpi0: bus 2 (RP02)
acpiprt3 at acpi0: bus 3 (RP03)
acpiprt4 at acpi0: bus 4 (RP04)
acpiec0 at acpi0: not present
acpicpu0 at acpi0: C3(10@1500 mwait.1@0x52), C2(10@500 mwait.1@0x51), C1(1000@1 mwait.1), PSS
acpicpu1 at acpi0: C3(10@1500 mwait.1@0x52), C2(10@500 mwait.1@0x51), C1(1000@1 mwait.1), PSS
acpicpu2 at acpi0: C3(10@1500 mwait.1@0x52), C2(10@500 mwait.1@0x51), C1(1000@1 mwait.1), PSS
acpicpu3 at acpi0: C3(10@1500 mwait.1@0x52), C2(10@500 mwait.1@0x51), C1(1000@1 mwait.1), PSS
acpipwrres0 at acpi0: PLPE
acpipwrres1 at acpi0: PLPE
acpipwrres2 at acpi0: USBC, resource for EHC1, OTG1
acpipwrres3 at acpi0: FN00, resource for FAN0
acpitz0 at acpi0: critical temperature is 90 degC
acpibat0 at acpi0: BAT0 not present
acpibat1 at acpi0: BAT1 not present
acpibat2 at acpi0: BAT2 not present
acpibtn0 at acpi0: LID0
acpibtn1 at acpi0: PWRB
acpibtn2 at acpi0: SLPB
acpivideo0 at acpi0: GFX0
acpivout0 at acpivideo0: DD1F
cpu0: Enhanced SpeedStep 2000 MHz: speeds: 1993, 1992, 1909, 1826, 1743, 1660, 1577, 1494, 1411, 1328 MHz
pci0 at mainbus0 bus 0
pchb0 at pci0 dev 0 function 0 "Intel Bay Trail Host" rev 0x0e
"Intel Bay Trail Video" rev 0x0e at pci0 dev 2 function 0 not configured
ahci0 at pci0 dev 19 function 0 "Intel Bay Trail AHCI" rev 0x0e: msi, AHCI 1.3
ahci0: port 0: 3.0Gb/s
ahci0: port 1: 1.5Gb/s
scsibus1 at ahci0: 32 targets
sd0 at scsibus1 targ 0 lun 0: <ATA, TOSHIBA MQ02ABF1, DS00> SCSI3 0/direct fixed naa.5000039664901d33
sd0: 953869MB, 512 bytes/sector, 1953525168 sectors
cd0 at scsibus1 targ 1 lun 0: <TEAC, BD-W26SS-B, 1.01> ATAPI 5/cdrom removable
xhci0 at pci0 dev 20 function 0 "Intel Bay Trail xHCI" rev 0x0e: msi
usb0 at xhci0: USB revision 3.0
uhub0 at usb0 "Intel xHCI root hub" rev 3.00/1.00 addr 1
"Intel Bay Trail TXE" rev 0x0e at pci0 dev 26 function 0 not configured
azalia0 at pci0 dev 27 function 0 "Intel Bay Trail HD Audio" rev 0x0e: msi
azalia0: codecs: Realtek ALC269, Intel/0x2882, using Realtek ALC269
audio0 at azalia0
ppb0 at pci0 dev 28 function 0 "Intel Bay Trail I2C" rev 0x0e: msi
pci1 at ppb0 bus 1
vendor "Realtek", unknown product 0x8179 (class network subclass miscellaneous, rev 0x01) at pci1 dev 0 function 0 not configured
ppb1 at pci0 dev 28 function 1 "Intel Bay Trail PCIE" rev 0x0e: msi
pci2 at ppb1 bus 2
rtsx0 at pci2 dev 0 function 0 "Realtek RTL8411 Card Reader" rev 0x01: msi
sdmmc0 at rtsx0
re0 at pci2 dev 0 function 2 "Realtek 8168" rev 0x0a: RTL8411 (0x4880), msi, address 80:ee:73:af:54:55
rgephy0 at re0 phy 7: RTL8169S/8110S/8211 PHY, rev. 5
ppb2 at pci0 dev 28 function 2 "Intel Bay Trail PCIE" rev 0x0e: msi
pci3 at ppb2 bus 3
ppb3 at pci0 dev 28 function 3 "Intel Bay Trail PCIE" rev 0x0e: msi
pci4 at ppb3 bus 4
ehci0 at pci0 dev 29 function 0 vendor "Intel", unknown product 0x0f34 rev 0x0e: apic 1 int 23
usb1 at ehci0: USB revision 2.0
uhub1 at usb1 "Intel EHCI root hub" rev 2.00/1.00 addr 1
pcib0 at pci0 dev 31 function 0 "Intel Bay Trail LPC" rev 0x0e
ichiic0 at pci0 dev 31 function 3 "Intel Bay Trail SMBus" rev 0x0e: apic 1 int 18
iic0 at ichiic0
spdmem0 at iic0 addr 0x50: 8GB DDR3 SDRAM PC3-10600 SO-DIMM
isa0 at pcib0
isadma0 at isa0
pcppi0 at isa0 port 0x61
spkr0 at pcppi0
it0 at isa0 port 0x2e/2: IT8728F rev 1, EC port 0xa40
efifb0 at mainbus0
wsdisplay0 at efifb0 mux 1: console (std, vt100 emulation)
wsdisplay0: screen 1-5 added (std, vt100 emulation)
uhub2 at uhub0 port 1 "Apple, Inc. Keyboard Hub" rev 2.00/96.15 addr 2
uhidev0 at uhub2 port 2 configuration 1 interface 0 "Apple Inc. Apple Keyboard" rev 2.00/0.74 addr 3
uhidev0: iclass 3/1
ukbd0 at uhidev0: 8 variable keys, 5 key codes, country code 13
wskbd0 at ukbd0: console keyboard, using wsdisplay0
uhidev1 at uhub2 port 2 configuration 1 interface 1 "Apple Inc. Apple Keyboard" rev 2.00/0.74 addr 3
uhidev1: iclass 3/0
uhid0 at uhidev1: input=1, output=0, feature=0
uhub3 at uhub0 port 4 "Genesys Logic USB2.0 Hub" rev 2.00/85.37 addr 4
urtwn0 at uhub3 port 2 configuration 1 interface 0 "Realtek 802.11n WLAN Adapter" rev 2.00/2.00 addr 5
urtwn0: MAC/BB RTL8188CUS, RF 6052 1T1R, address 74:da:38:1a:bc:46
ehci_sync_hc: tsleep() = 35
ehci_sync_hc: tsleep() = 35
ehci_sync_hc: tsleep() = 35
ehci_sync_hc: tsleep() = 35
ehci_sync_hc: tsleep() = 35
ehci_sync_hc: tsleep() = 35
ehci_sync_hc: tsleep() = 35
ehci_sync_hc: tsleep() = 35
uhub1: device problem, disabling port 1
vscsi0 at root
scsibus2 at vscsi0: 256 targets
softraid0 at root
scsibus3 at softraid0: 256 targets
root on sd0a (cd1e7de4a625601f.a) swap on sd0b dump on sd0b
uhidev2 at uhub2 port 1 configuration 1 interface 0 "Microsoft Microsoft\M-. Comfort Mouse 4500" rev 2.00/0.83 addr 6
uhidev2: iclass 3/1, 28 report ids
ums0 at uhidev2 reportid 16: 5 buttons, Z dir
wsmouse0 at ums0 mux 0
uhid1 at uhidev2 reportid 18: input=0, output=0, feature=1
uhid2 at uhidev2 reportid 19: input=1, output=0, feature=0
uhid3 at uhidev2 reportid 22: input=4, output=0, feature=0
uhid4 at uhidev2 reportid 23: input=0, output=0, feature=1
uhid5 at uhidev2 reportid 24: input=0, output=0, feature=1
uhid6 at uhidev2 reportid 28: input=1, output=0, feature=0
syncing disks... done
ehci0: halt timeout
wsdisplay_switch2: not switching
rebooting...
OpenBSD 5.8-current (GENERIC.MP) #1537: Tue Oct 20 09:44:09 MDT 2015
    deraadt@amd64.openbsd.org:/usr/src/sys/arch/amd64/compile/GENERIC.MP
RTC BIOS diagnostic error f<fixed_disk,invalid_time>
real mem = 7970746368 (7601MB)
avail mem = 7725047808 (7367MB)
mpath0 at root
scsibus0 at mpath0: 256 targets
mainbus0 at root
bios0 at mainbus0: SMBIOS rev. 2.8 @ 0xebd30 (52 entries)
bios0: vendor American Megatrends Inc. version "1.11  x64" date 08/26/2014
bios0: Shuttle Inc. XS35V4
acpi0 at bios0: rev 2
acpi0: sleep states S0 S3 S4 S5
acpi0: tables DSDT FACP APIC FPDT MCFG LPIT SLIC HPET SSDT SSDT SSDT UEFI
acpi0: wakeup devices UAR5(S4) UAR8(S4) XHC1(S4) EHC1(S4) PXSX(S4) PXSX(S4) RLAN(S5) PXSX(S4) PXSX(S4) PWRB(S0)
acpitimer0 at acpi0: 3579545 Hz, 24 bits
acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat
cpu0 at mainbus0: apid 0 (boot processor)
cpu0: Intel(R) Celeron(R) CPU J1900 @ 1.99GHz, 2000.37 MHz
cpu0: FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,PCLMUL,DTES64,MWAIT,DS-CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,SSE4.1,SSE4.2,MOVBE,POPCNT,DEADLINE,RDRAND,NXE,LONG,LAHF,3DNOWP,PERF,ITSC,SMEP,ERMS,SENSOR,ARAT
cpu0: 1MB 64b/line 16-way L2 cache
cpu0: smt 0, core 0, package 0
mtrr: Pentium Pro MTRR support, 8 var ranges, 88 fixed ranges
cpu0: apic clock running at 83MHz
cpu0: mwait min=64, max=64, C-substates=0.2.0.0.0.0.3.3, IBE
cpu1 at mainbus0: apid 2 (application processor)
cpu1: Intel(R) Celeron(R) CPU J1900 @ 1.99GHz, 2000.01 MHz
cpu1: FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,PCLMUL,DTES64,MWAIT,DS-CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,SSE4.1,SSE4.2,MOVBE,POPCNT,DEADLINE,RDRAND,NXE,LONG,LAHF,3DNOWP,PERF,ITSC,SMEP,ERMS,SENSOR,ARAT
cpu1: 1MB 64b/line 16-way L2 cache
cpu1: smt 0, core 1, package 0
cpu2 at mainbus0: apid 4 (application processor)
cpu2: Intel(R) Celeron(R) CPU J1900 @ 1.99GHz, 2000.01 MHz
cpu2: FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,PCLMUL,DTES64,MWAIT,DS-CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,SSE4.1,SSE4.2,MOVBE,POPCNT,DEADLINE,RDRAND,NXE,LONG,LAHF,3DNOWP,PERF,ITSC,SMEP,ERMS,SENSOR,ARAT
cpu2: 1MB 64b/line 16-way L2 cache
cpu2: smt 0, core 2, package 0
cpu3 at mainbus0: apid 6 (application processor)
cpu3: Intel(R) Celeron(R) CPU J1900 @ 1.99GHz, 2000.01 MHz
cpu3: FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,PCLMUL,DTES64,MWAIT,DS-CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,SSE4.1,SSE4.2,MOVBE,POPCNT,DEADLINE,RDRAND,NXE,LONG,LAHF,3DNOWP,PERF,ITSC,SMEP,ERMS,SENSOR,ARAT
cpu3: 1MB 64b/line 16-way L2 cache
cpu3: smt 0, core 3, package 0
ioapic0 at mainbus0: apid 1 pa 0xfec00000, version 20, 87 pins
acpimadt0: bogus nmi for apid 0
acpimadt0: bogus nmi for apid 2
acpimadt0: bogus nmi for apid 4
acpimadt0: bogus nmi for apid 6
acpimcfg0 at acpi0 addr 0xe0000000, bus 0-255
acpihpet0 at acpi0: 14318179 Hz
acpiprt0 at acpi0: bus 0 (PCI0)
acpiprt1 at acpi0: bus 1 (RP01)
acpiprt2 at acpi0: bus 2 (RP02)
acpiprt3 at acpi0: bus 3 (RP03)
acpiprt4 at acpi0: bus 4 (RP04)
acpiec0 at acpi0: not present
acpicpu0 at acpi0: C3(10@1500 mwait.1@0x52), C2(10@500 mwait.1@0x51), C1(1000@1 mwait.1), PSS
acpicpu1 at acpi0: C3(10@1500 mwait.1@0x52), C2(10@500 mwait.1@0x51), C1(1000@1 mwait.1), PSS
acpicpu2 at acpi0: C3(10@1500 mwait.1@0x52), C2(10@500 mwait.1@0x51), C1(1000@1 mwait.1), PSS
acpicpu3 at acpi0: C3(10@1500 mwait.1@0x52), C2(10@500 mwait.1@0x51), C1(1000@1 mwait.1), PSS
acpipwrres0 at acpi0: PLPE
acpipwrres1 at acpi0: PLPE
acpipwrres2 at acpi0: USBC, resource for EHC1, OTG1
acpipwrres3 at acpi0: FN00, resource for FAN0
acpitz0 at acpi0: critical temperature is 90 degC
acpibat0 at acpi0: BAT0 not present
acpibat1 at acpi0: BAT1 not present
acpibat2 at acpi0: BAT2 not present
acpibtn0 at acpi0: LID0
acpibtn1 at acpi0: PWRB
acpibtn2 at acpi0: SLPB
acpivideo0 at acpi0: GFX0
acpivout0 at acpivideo0: DD1F
cpu0: Enhanced SpeedStep 2000 MHz: speeds: 1993, 1992, 1909, 1826, 1743, 1660, 1577, 1494, 1411, 1328 MHz
pci0 at mainbus0 bus 0
pchb0 at pci0 dev 0 function 0 "Intel Bay Trail Host" rev 0x0e
"Intel Bay Trail Video" rev 0x0e at pci0 dev 2 function 0 not configured
ahci0 at pci0 dev 19 function 0 "Intel Bay Trail AHCI" rev 0x0e: msi, AHCI 1.3
ahci0: port 0: 3.0Gb/s
ahci0: port 1: 1.5Gb/s
scsibus1 at ahci0: 32 targets
sd0 at scsibus1 targ 0 lun 0: <ATA, TOSHIBA MQ02ABF1, DS00> SCSI3 0/direct fixed naa.5000039664901d33
sd0: 953869MB, 512 bytes/sector, 1953525168 sectors
cd0 at scsibus1 targ 1 lun 0: <TEAC, BD-W26SS-B, 1.01> ATAPI 5/cdrom removable
xhci0 at pci0 dev 20 function 0 "Intel Bay Trail xHCI" rev 0x0e: msi
usb0 at xhci0: USB revision 3.0
uhub0 at usb0 "Intel xHCI root hub" rev 3.00/1.00 addr 1
"Intel Bay Trail TXE" rev 0x0e at pci0 dev 26 function 0 not configured
azalia0 at pci0 dev 27 function 0 "Intel Bay Trail HD Audio" rev 0x0e: msi
azalia0: codecs: Realtek ALC269, Intel/0x2882, using Realtek ALC269
audio0 at azalia0
ppb0 at pci0 dev 28 function 0 "Intel Bay Trail I2C" rev 0x0e: msi
pci1 at ppb0 bus 1
vendor "Realtek", unknown product 0x8179 (class network subclass miscellaneous, rev 0x01) at pci1 dev 0 function 0 not configured
ppb1 at pci0 dev 28 function 1 "Intel Bay Trail PCIE" rev 0x0e: msi
pci2 at ppb1 bus 2
rtsx0 at pci2 dev 0 function 0 "Realtek RTL8411 Card Reader" rev 0x01: msi
sdmmc0 at rtsx0
re0 at pci2 dev 0 function 2 "Realtek 8168" rev 0x0a: RTL8411 (0x4880), msi, address 80:ee:73:af:54:55
rgephy0 at re0 phy 7: RTL8169S/8110S/8211 PHY, rev. 5
ppb2 at pci0 dev 28 function 2 "Intel Bay Trail PCIE" rev 0x0e: msi
pci3 at ppb2 bus 3
ppb3 at pci0 dev 28 function 3 "Intel Bay Trail PCIE" rev 0x0e: msi
pci4 at ppb3 bus 4
ehci0 at pci0 dev 29 function 0 vendor "Intel", unknown product 0x0f34 rev 0x0e: apic 1 int 23
usb1 at ehci0: USB revision 2.0
uhub1 at usb1 "Intel EHCI root hub" rev 2.00/1.00 addr 1
pcib0 at pci0 dev 31 function 0 "Intel Bay Trail LPC" rev 0x0e
ichiic0 at pci0 dev 31 function 3 "Intel Bay Trail SMBus" rev 0x0e: apic 1 int 18
iic0 at ichiic0
spdmem0 at iic0 addr 0x50: 8GB DDR3 SDRAM PC3-10600 SO-DIMM
isa0 at pcib0
isadma0 at isa0
pcppi0 at isa0 port 0x61
spkr0 at pcppi0
it0 at isa0 port 0x2e/2: IT8728F rev 1, EC port 0xa40
efifb0 at mainbus0
wsdisplay0 at efifb0 mux 1: console (std, vt100 emulation)
wsdisplay0: screen 1-5 added (std, vt100 emulation)
uhub2 at uhub0 port 1 "Apple, Inc. Keyboard Hub" rev 2.00/96.15 addr 2
uhidev0 at uhub2 port 2 configuration 1 interface 0 "Apple Inc. Apple Keyboard" rev 2.00/0.74 addr 3
uhidev0: iclass 3/1
ukbd0 at uhidev0: 8 variable keys, 5 key codes, country code 13
wskbd0 at ukbd0: console keyboard, using wsdisplay0
uhidev1 at uhub2 port 2 configuration 1 interface 1 "Apple Inc. Apple Keyboard" rev 2.00/0.74 addr 3
uhidev1: iclass 3/0
uhid0 at uhidev1: input=1, output=0, feature=0
uhub3 at uhub0 port 4 "Genesys Logic USB2.0 Hub" rev 2.00/85.37 addr 4
urtwn0 at uhub3 port 2 configuration 1 interface 0 "Realtek 802.11n WLAN Adapter" rev 2.00/2.00 addr 5
urtwn0: MAC/BB RTL8188CUS, RF 6052 1T1R, address 74:da:38:1a:bc:46
ehci_sync_hc: tsleep() = 35
ehci_sync_hc: tsleep() = 35
ehci_sync_hc: tsleep() = 35
ehci_sync_hc: tsleep() = 35
ehci_sync_hc: tsleep() = 35
ehci_sync_hc: tsleep() = 35
ehci_sync_hc: tsleep() = 35
ehci_sync_hc: tsleep() = 35
uhub1: device problem, disabling port 1
vscsi0 at root
scsibus2 at vscsi0: 256 targets
softraid0 at root
scsibus3 at softraid0: 256 targets
root on sd0a (cd1e7de4a625601f.a) swap on sd0b dump on sd0b
uhidev2 at uhub2 port 1 configuration 1 interface 0 "Microsoft Microsoft\M-. Comfort Mouse 4500" rev 2.00/0.83 addr 6
uhidev2: iclass 3/1, 28 report ids
ums0 at uhidev2 reportid 16: 5 buttons, Z dir
wsmouse0 at ums0 mux 0
uhid1 at uhidev2 reportid 18: input=0, output=0, feature=1
uhid2 at uhidev2 reportid 19: input=1, output=0, feature=0
uhid3 at uhidev2 reportid 22: input=4, output=0, feature=0
uhid4 at uhidev2 reportid 23: input=0, output=0, feature=1
uhid5 at uhidev2 reportid 24: input=0, output=0, feature=1
uhid6 at uhidev2 reportid 28: input=1, output=0, feature=0
urtwn0: could not load firmware page 1 (error 15)
urtwn0 detached
urtwn0 at uhub3 port 2 configuration 1 interface 0 "Realtek 802.11n WLAN Adapter" rev 2.00/2.00 addr 5
urtwn0: MAC/BB RTL8188CUS, RF 6052 1T1R, address 74:da:38:1a:bc:46
urtwn0 detached
urtwn0 at uhub3 port 2 configuration 1 interface 0 "Realtek 802.11n WLAN Adapter" rev 2.00/2.00 addr 5
urtwn0: MAC/BB RTL8188CUS, RF 6052 1T1R, address 74:da:38:1a:bc:46
syncing disks... done
ehci0: halt timeout
wsdisplay_switch2: not switching
rebooting...
OpenBSD 5.8-current (GENERIC.MP) #1537: Tue Oct 20 09:44:09 MDT 2015
    deraadt@amd64.openbsd.org:/usr/src/sys/arch/amd64/compile/GENERIC.MP
RTC BIOS diagnostic error f<fixed_disk,invalid_time>
real mem = 7970746368 (7601MB)
avail mem = 7725047808 (7367MB)
mpath0 at root
scsibus0 at mpath0: 256 targets
mainbus0 at root
bios0 at mainbus0: SMBIOS rev. 2.8 @ 0xebd30 (52 entries)
bios0: vendor American Megatrends Inc. version "1.11  x64" date 08/26/2014
bios0: Shuttle Inc. XS35V4
acpi0 at bios0: rev 2
acpi0: sleep states S0 S3 S4 S5
acpi0: tables DSDT FACP APIC FPDT MCFG LPIT SLIC HPET SSDT SSDT SSDT UEFI
acpi0: wakeup devices UAR5(S4) UAR8(S4) XHC1(S4) EHC1(S4) PXSX(S4) PXSX(S4) RLAN(S5) PXSX(S4) PXSX(S4) PWRB(S0)
acpitimer0 at acpi0: 3579545 Hz, 24 bits
acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat
cpu0 at mainbus0: apid 0 (boot processor)
cpu0: Intel(R) Celeron(R) CPU J1900 @ 1.99GHz, 2000.38 MHz
cpu0: FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,PCLMUL,DTES64,MWAIT,DS-CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,SSE4.1,SSE4.2,MOVBE,POPCNT,DEADLINE,RDRAND,NXE,LONG,LAHF,3DNOWP,PERF,ITSC,SMEP,ERMS,SENSOR,ARAT
cpu0: 1MB 64b/line 16-way L2 cache
cpu0: smt 0, core 0, package 0
mtrr: Pentium Pro MTRR support, 8 var ranges, 88 fixed ranges
cpu0: apic clock running at 83MHz
cpu0: mwait min=64, max=64, C-substates=0.2.0.0.0.0.3.3, IBE
cpu1 at mainbus0: apid 2 (application processor)
cpu1: Intel(R) Celeron(R) CPU J1900 @ 1.99GHz, 2000.01 MHz
cpu1: FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,PCLMUL,DTES64,MWAIT,DS-CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,SSE4.1,SSE4.2,MOVBE,POPCNT,DEADLINE,RDRAND,NXE,LONG,LAHF,3DNOWP,PERF,ITSC,SMEP,ERMS,SENSOR,ARAT
cpu1: 1MB 64b/line 16-way L2 cache
cpu1: smt 0, core 1, package 0
cpu2 at mainbus0: apid 4 (application processor)
cpu2: Intel(R) Celeron(R) CPU J1900 @ 1.99GHz, 2000.01 MHz
cpu2: FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,PCLMUL,DTES64,MWAIT,DS-CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,SSE4.1,SSE4.2,MOVBE,POPCNT,DEADLINE,RDRAND,NXE,LONG,LAHF,3DNOWP,PERF,ITSC,SMEP,ERMS,SENSOR,ARAT
cpu2: 1MB 64b/line 16-way L2 cache
cpu2: smt 0, core 2, package 0
cpu3 at mainbus0: apid 6 (application processor)
cpu3: Intel(R) Celeron(R) CPU J1900 @ 1.99GHz, 2000.01 MHz
cpu3: FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,PCLMUL,DTES64,MWAIT,DS-CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,SSE4.1,SSE4.2,MOVBE,POPCNT,DEADLINE,RDRAND,NXE,LONG,LAHF,3DNOWP,PERF,ITSC,SMEP,ERMS,SENSOR,ARAT
cpu3: 1MB 64b/line 16-way L2 cache
cpu3: smt 0, core 3, package 0
ioapic0 at mainbus0: apid 1 pa 0xfec00000, version 20, 87 pins
acpimadt0: bogus nmi for apid 0
acpimadt0: bogus nmi for apid 2
acpimadt0: bogus nmi for apid 4
acpimadt0: bogus nmi for apid 6
acpimcfg0 at acpi0 addr 0xe0000000, bus 0-255
acpihpet0 at acpi0: 14318179 Hz
acpiprt0 at acpi0: bus 0 (PCI0)
acpiprt1 at acpi0: bus 1 (RP01)
acpiprt2 at acpi0: bus 2 (RP02)
acpiprt3 at acpi0: bus 3 (RP03)
acpiprt4 at acpi0: bus 4 (RP04)
acpiec0 at acpi0: not present
acpicpu0 at acpi0: C3(10@1500 mwait.1@0x52), C2(10@500 mwait.1@0x51), C1(1000@1 mwait.1), PSS
acpicpu1 at acpi0: C3(10@1500 mwait.1@0x52), C2(10@500 mwait.1@0x51), C1(1000@1 mwait.1), PSS
acpicpu2 at acpi0: C3(10@1500 mwait.1@0x52), C2(10@500 mwait.1@0x51), C1(1000@1 mwait.1), PSS
acpicpu3 at acpi0: C3(10@1500 mwait.1@0x52), C2(10@500 mwait.1@0x51), C1(1000@1 mwait.1), PSS
acpipwrres0 at acpi0: PLPE
acpipwrres1 at acpi0: PLPE
acpipwrres2 at acpi0: USBC, resource for EHC1, OTG1
acpipwrres3 at acpi0: FN00, resource for FAN0
acpitz0 at acpi0: critical temperature is 90 degC
acpibat0 at acpi0: BAT0 not present
acpibat1 at acpi0: BAT1 not present
acpibat2 at acpi0: BAT2 not present
acpibtn0 at acpi0: LID0
acpibtn1 at acpi0: PWRB
acpibtn2 at acpi0: SLPB
acpivideo0 at acpi0: GFX0
acpivout0 at acpivideo0: DD1F
cpu0: Enhanced SpeedStep 2000 MHz: speeds: 1993, 1992, 1909, 1826, 1743, 1660, 1577, 1494, 1411, 1328 MHz
pci0 at mainbus0 bus 0
pchb0 at pci0 dev 0 function 0 "Intel Bay Trail Host" rev 0x0e
"Intel Bay Trail Video" rev 0x0e at pci0 dev 2 function 0 not configured
ahci0 at pci0 dev 19 function 0 "Intel Bay Trail AHCI" rev 0x0e: msi, AHCI 1.3
ahci0: port 0: 3.0Gb/s
ahci0: port 1: 1.5Gb/s
scsibus1 at ahci0: 32 targets
sd0 at scsibus1 targ 0 lun 0: <ATA, TOSHIBA MQ02ABF1, DS00> SCSI3 0/direct fixed naa.5000039664901d33
sd0: 953869MB, 512 bytes/sector, 1953525168 sectors
cd0 at scsibus1 targ 1 lun 0: <TEAC, BD-W26SS-B, 1.01> ATAPI 5/cdrom removable
xhci0 at pci0 dev 20 function 0 "Intel Bay Trail xHCI" rev 0x0e: msi
usb0 at xhci0: USB revision 3.0
uhub0 at usb0 "Intel xHCI root hub" rev 3.00/1.00 addr 1
"Intel Bay Trail TXE" rev 0x0e at pci0 dev 26 function 0 not configured
azalia0 at pci0 dev 27 function 0 "Intel Bay Trail HD Audio" rev 0x0e: msi
azalia0: codecs: Realtek ALC269, Intel/0x2882, using Realtek ALC269
audio0 at azalia0
ppb0 at pci0 dev 28 function 0 "Intel Bay Trail I2C" rev 0x0e: msi
pci1 at ppb0 bus 1
vendor "Realtek", unknown product 0x8179 (class network subclass miscellaneous, rev 0x01) at pci1 dev 0 function 0 not configured
ppb1 at pci0 dev 28 function 1 "Intel Bay Trail PCIE" rev 0x0e: msi
pci2 at ppb1 bus 2
rtsx0 at pci2 dev 0 function 0 "Realtek RTL8411 Card Reader" rev 0x01: msi
sdmmc0 at rtsx0
re0 at pci2 dev 0 function 2 "Realtek 8168" rev 0x0a: RTL8411 (0x4880), msi, address 80:ee:73:af:54:55
rgephy0 at re0 phy 7: RTL8169S/8110S/8211 PHY, rev. 5
ppb2 at pci0 dev 28 function 2 "Intel Bay Trail PCIE" rev 0x0e: msi
pci3 at ppb2 bus 3
ppb3 at pci0 dev 28 function 3 "Intel Bay Trail PCIE" rev 0x0e: msi
pci4 at ppb3 bus 4
ehci0 at pci0 dev 29 function 0 vendor "Intel", unknown product 0x0f34 rev 0x0e: apic 1 int 23
usb1 at ehci0: USB revision 2.0
uhub1 at usb1 "Intel EHCI root hub" rev 2.00/1.00 addr 1
pcib0 at pci0 dev 31 function 0 "Intel Bay Trail LPC" rev 0x0e
ichiic0 at pci0 dev 31 function 3 "Intel Bay Trail SMBus" rev 0x0e: apic 1 int 18
iic0 at ichiic0
spdmem0 at iic0 addr 0x50: 8GB DDR3 SDRAM PC3-10600 SO-DIMM
isa0 at pcib0
isadma0 at isa0
pcppi0 at isa0 port 0x61
spkr0 at pcppi0
it0 at isa0 port 0x2e/2: IT8728F rev 1, EC port 0xa40
efifb0 at mainbus0
wsdisplay0 at efifb0 mux 1: console (std, vt100 emulation)
wsdisplay0: screen 1-5 added (std, vt100 emulation)
uhub2 at uhub0 port 1 "Apple, Inc. Keyboard Hub" rev 2.00/96.15 addr 2
uhidev0 at uhub2 port 2 configuration 1 interface 0 "Apple Inc. Apple Keyboard" rev 2.00/0.74 addr 3
uhidev0: iclass 3/1
ukbd0 at uhidev0: 8 variable keys, 5 key codes, country code 13
wskbd0 at ukbd0: console keyboard, using wsdisplay0
uhidev1 at uhub2 port 2 configuration 1 interface 1 "Apple Inc. Apple Keyboard" rev 2.00/0.74 addr 3
uhidev1: iclass 3/0
uhid0 at uhidev1: input=1, output=0, feature=0
uhub3 at uhub0 port 4 "Genesys Logic USB2.0 Hub" rev 2.00/85.37 addr 4
urtwn0 at uhub3 port 2 configuration 1 interface 0 "Realtek 802.11n WLAN Adapter" rev 2.00/2.00 addr 5
urtwn0: MAC/BB RTL8188CUS, RF 6052 1T1R, address 74:da:38:1a:bc:46
ehci_sync_hc: tsleep() = 35
ehci_sync_hc: tsleep() = 35
ehci_sync_hc: tsleep() = 35
ehci_sync_hc: tsleep() = 35
ehci_sync_hc: tsleep() = 35
ehci_sync_hc: tsleep() = 35
ehci_sync_hc: tsleep() = 35
ehci_sync_hc: tsleep() = 35
uhub1: device problem, disabling port 1
vscsi0 at root
scsibus2 at vscsi0: 256 targets
softraid0 at root
scsibus3 at softraid0: 256 targets
root on sd0a (cd1e7de4a625601f.a) swap on sd0b dump on sd0b
uhidev2 at uhub2 port 1 configuration 1 interface 0 "Microsoft Microsoft\M-. Comfort Mouse 4500" rev 2.00/0.83 addr 6
uhidev2: iclass 3/1, 28 report ids
ums0 at uhidev2 reportid 16: 5 buttons, Z dir
wsmouse0 at ums0 mux 0
uhid1 at uhidev2 reportid 18: input=0, output=0, feature=1
uhid2 at uhidev2 reportid 19: input=1, output=0, feature=0
uhid3 at uhidev2 reportid 22: input=4, output=0, feature=0
uhid4 at uhidev2 reportid 23: input=0, output=0, feature=1
uhid5 at uhidev2 reportid 24: input=0, output=0, feature=1
uhid6 at uhidev2 reportid 28: input=1, output=0, feature=0
umass0 at uhub0 port 2 configuration 1 interface 0 "Generic USB Storage" rev 2.00/2.72 addr 7
umass0: using SCSI over Bulk-Only
scsibus4 at umass0: 2 targets, initiator 0
sd1 at scsibus4 targ 1 lun 0: <Generic, STORAGE DEVICE, 0272> SCSI0 0/direct removable serial.05e30736000000000272
sd1: 7655MB, 512 bytes/sector, 15677440 sectors
sd1 detached
scsibus4 detached
umass0 detached

Thanks for ideas.

jggimi · #2 **(View Single Post)** 28th October 2015

http://www.storagereview.com/how_to_...s_with_wdidle3

I recommend you contact Toshiba technical support regarding your concern; perhaps they have a similar tool.

NaWi · #3 **(View Single Post)** 28th October 2015

Thanks for your answer.

Good to know, that it is not my fault ;-)

Based on my Lenovo support experience, I keep my fingers away from any company support. I will replace the drive with one which is better supported (HD / SSD - if I found some informations, which I should take and which has a long life).

kpa · #4 **(View Single Post)** 28th October 2015

I have no idea if OpenBSD has a similar utility but on FreeBSD you would use sysutils/ataidle (quick test with pkg_add revealed no OpenBSD package) to turn off the APM features on the drive and the head parking with it.

NaWi · #5 **(View Single Post)** 28th October 2015

Thanks for your answer.

The atactl command itself includes the option apmdisable and setidle / setstandby but as it looks now, none has a effect (I will give it a try during night).

http://www.openbsd.org/cgi-bin/man.c...8?query=atactl

bashrules · #6 **(View Single Post)** 29th October 2015

Quote:

Originally Posted by NaWi

Thanks for your answer.

The atactl command itself includes the option apmdisable and setidle / setstandby but as it looks now, none has a effect (I will give it a try during night).

Same here on NetBSD: apmdisable hasn't worked for me. What worked for me on NetBSD was

Code:

atactl wd0 apm set 253

For reasons unknown, numbers higher than 253 have not worked. Try that on your flavor of BSD - also experiment with the actual number ...

NaWi · #7 **(View Single Post)** 29th October 2015

Thanks for your answer and the idea, let's call the question as solved.

The correct command (depends only on the drive) on OpenBSD is

Code:

atactl sd0 apmset 253

Quote:

Originally Posted by bashrules

For reasons unknown, numbers higher than 253 have not worked.

It is because they are not there / not implemented in NetBSD / OpenBSD (the information is from the man page). You can use 0 - 126 which allowes the drive to go to standby and 127 - 253 which doesn't allow the drive to go to standby.

With the above setting I have reound 3 Load Cycle Counts per round 30 minutes.

bashrules · #8 **(View Single Post)** 6th November 2015

Quote:

Originally Posted by NaWi

Thanks for your answer and the idea, let's call the question as solved.

The correct command (depends only on the drive) on OpenBSD is

Code:

atactl sd0 apmset 253

With the above setting I have reound 3 Load Cycle Counts per round 30 minutes.

3 LCCs per 30 min is still high - it should be 0. In a desperate attempt, you could run a script in an xterm keeping the hd busy (toy around with the sleep argument)

Code:

$ while true; do touch /tmp/touch.txt; echo -n .; sleep 10; done

NaWi · #9 **(View Single Post)** 9th November 2015

Thanks for the tip. I let it at the moment as it is because for now I don't know, whether I keep the hardware or not (I also don't use it at the moment). If yes, I will give it a try.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
formally in 5.8-beta cycle	ocicat	OpenBSD General	2	22nd June 2015 01:06 PM
OpenBSD OpenBSD 4.9-beta cycle has begun	ocicat	News	0	15th January 2011 08:27 AM
usb modem toshiba g450+freebsd8.0	xnl96	FreeBSD General	4	3rd October 2009 12:04 PM
cannot install freebsd on toshiba tecra R10 10K	koukisaad	FreeBSD Installation and Upgrading	5	24th September 2009 10:18 AM