NetBSD 10 RC_4 experiences

[J65nko]

A few days ago I installed the 4th release candidate of NetBSD on a 32 GB USB 3.0 memory stick.

Install went well and fast. After booting up I installed the Firefox compiled package with pkgin This also went smooth.

I did not have to do anything for the X configuration. But when I started firefox the system became unresponsive (crashed) and seemed to be busy writing a dump file.
Sometimes OpenBSD also shows the same behaviour on this system. Powering off is the only way to regain control.

The system I used is my grumpy HP Proliant server. Linux, FreeBSD and DragonFlyBSD complain that about mixed 32bit and 64bit ACPI data.
The cheap 64bit Xeon CPU has a built-in Matrox VGA processor (mga driver in X Window) and probably uses part of the normal ECC RAM.

NetBSD also mentions problems with the ACPI stuff. It seems to truncate some entries:
The dmesg:

$ sed -e "s/^\[    /[/" U/dmesg_netbsd10_rc4.txt

[ 1.000000] Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003,
[ 1.000000]     2004, 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013,
[ 1.000000]     2014, 2015, 2016, 2017, 2018, 2019, 2020, 2021, 2022, 2023,
[ 1.000000]     2024
[ 1.000000]     The NetBSD Foundation, Inc.  All rights reserved.
[ 1.000000] Copyright (c) 1982, 1986, 1989, 1991, 1993
[ 1.000000]     The Regents of the University of California.  All rights reserved.

[ 1.000000] NetBSD 10.0_RC4 (GENERIC) #0: Tue Feb  6 12:38:53 UTC 2024
[ 1.000000]     mkrepro@mkrepro.NetBSD.org:/usr/src/sys/arch/amd64/compile/GENERIC
[ 1.000000] total memory = 4061 MB
[ 1.000000] avail memory = 3902 MB
[ 1.000000] timecounter: Timecounters tick every 10.000 msec
[ 1.000000] Kernelized RAIDframe activated
[ 1.000000] timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
[ 1.000004] mainbus0 (root)
[ 1.000004] ACPI: RSDP 0x00000000000F4F00 000024 (v02 HP    )
[ 1.000004] ACPI: XSDT 0x00000000F1DE6400 0000B4 (v01 HP     ProLiant 00000002 ??   0000162E)
[ 1.000004] ACPI: FACP 0x00000000F1DE6540 0000F4 (v03 HP     ProLiant 00000002 ??   0000162E)
[ 1.000004] Firmware Warning (ACPI): 32/64X length mismatch in FADT/Pm1aControlBlock: 16/32 (20221020/tbfadt-640)
[ 1.000004] Firmware Warning (ACPI): 32/64X length mismatch in FADT/Pm2ControlBlock: 8/32 (20221020/tbfadt-640)
[ 1.000004] Firmware Warning (ACPI): Invalid length for FADT/Pm1aControlBlock: 32, using default 16 (20221020/tbfa
dt-742)
[ 1.000004] Firmware Warning (ACPI): Invalid length for FADT/Pm2ControlBlock: 32, using default 8 (20221020/tbfadt
-742)
[ 1.000004] ACPI: DSDT 0x00000000F1DE6640 002A13 (v01 HP     DSDT     00000001 INTL 20030228)
[ 1.000004] ACPI: FACS 0x00000000F1DE4140 000040
[ 1.000004] ACPI: SPCR 0x00000000F1DE4180 000050 (v01 HP     SPCRRBSU 00000001 ??   0000162E)
[ 1.000004] ACPI: MCFG 0x00000000F1DE4200 00003C (v01 HP     ProLiant 00000001      00000000)
[ 1.000004] ACPI: HPET 0x00000000F1DE4240 000038 (v01 HP     ProLiant 00000002 ??   0000162E)
[ 1.000004] ACPI: FFFF 0x00000000F1DE4280 000064 (v02 HP     ProLiant 00000002 ??   0000162E)
[ 1.000004] ACPI: SPMI 0x00000000F1DE4300 000040 (v05 HP     ProLiant 00000001 ??   0000162E)
[ 1.000004] ACPI: ERST 0x00000000F1DE4340 000230 (v01 HP     ProLiant 00000001 ??   0000162E)
[ 1.000004] ACPI: APIC 0x00000000F1DE4580 000252 (v01 HP     ProLiant 00000002      00000000)
[ 1.000004] ACPI: FFFF 0x00000000F1DE4800 000176 (v01 HP     ProLiant 00000001 ??   0000162E)
[ 1.000004] ACPI: BERT 0x00000000F1DE4980 000030 (v01 HP     ProLiant 00000001 ??   0000162E)
[ 1.000004] ACPI: HEST 0x00000000F1DE49C0 0000BC (v01 HP     ProLiant 00000001 ??   0000162E)
[ 1.000004] ACPI: DMAR 0x00000000F1DE4A80 00030E (v01 HP     ProLiant 00000001 ??   0000162E)
[ 1.000004] ACPI: FFFF 0x00000000F1DE63C0 00002D (v01 HP     ProLiant 00000001      00000000)
[ 1.000004] ACPI: SSDT 0x00000000F1DE9080 000137 (v03 HP     CRSPCI0  00000002 HP   00000001)
[ 1.000004] ACPI: SSDT 0x00000000F1DE91C0 000573 (v03 HP     riser0   00000002 INTL 20030228)
[ 1.000004] ACPI: SSDT 0x00000000F1DE9740 0001E1 (v01 HP     pcc      00000001 INTL 20090625)
[ 1.000004] ACPI: SSDT 0x00000000F1DE9940 000377 (v01 HP     pmab     00000001 INTL 20090625)
[ 1.000004] ACPI: SSDT 0x00000000F1DE9CC0 0009E4 (v01 INTEL  PPM RCM  80000001 INTL 20061109)
[ 1.000004] ACPI: 6 ACPI AML tables successfully acquired and loaded
[ 1.000004] ioapic0 at mainbus0 apid 8: pa 0xfec00000, version 0x20, 24 pins
[ 1.000004] x2APIC available but disabled by DMAR table
[ 1.000004] cpu0 at mainbus0 apid 0
[ 1.000004] cpu0: Use lfence to serialize rdtsc
[ 1.000004] cpu0: Intel(R) Xeon(R) CPU E3-1220 v3 @ 3.10GHz, id 0x306c3
[ 1.000004] cpu0: node 0, package 0, core 0, smt 0
[ 1.000004] cpu1 at mainbus0 apid 2
[ 1.000004] cpu1: Intel(R) Xeon(R) CPU E3-1220 v3 @ 3.10GHz, id 0x306c3
[ 1.000004] cpu1: node 0, package 0, core 1, smt 0
[ 1.000004] cpu2 at mainbus0 apid 4
[ 1.000004] cpu2: Intel(R) Xeon(R) CPU E3-1220 v3 @ 3.10GHz, id 0x306c3
[ 1.000004] cpu2: node 0, package 0, core 2, smt 0
[ 1.000004] cpu3 at mainbus0 apid 6
[ 1.000004] cpu3: Intel(R) Xeon(R) CPU E3-1220 v3 @ 3.10GHz, id 0x306c3
[ 1.000004] cpu3: node 0, package 0, core 3, smt 0
[ 1.000004] acpi0 at mainbus0: Intel ACPICA 20221020
[ 1.000004] acpi0: X/RSDT: OemId <HP    ,ProLiant,00000002>, AslId <  <2147483602>^D,0000162e>
[ 1.000004] acpi0: MCFG: segment 0, bus 0-63, address 0x00000000f4000000
[ 1.000004] acpi0: SCI interrupting at int 9
[ 1.000004] acpi0: fixed power button present
[ 1.000004] timecounter: Timecounter "ACPI-Fast" frequency 3579545 Hz quality 1000
[ 1.021219] hpet0 at acpi0: high precision event timer (mem 0xfed00000-0xfed00400)
[ 1.021219] timecounter: Timecounter "hpet0" frequency 14318180 Hz quality 2000
[ 1.021431] ipmi_acpi0 at acpi0 (MI0, IPI0001-0): io 0xca2-0xca3
[ 1.021431] ipmi0 at ipmi_acpi0
[ 1.021431] attimer1 at acpi0 (TIME, PNP0100): io 0x40-0x43 irq 0
[ 1.021431] pcppi1 at acpi0 (BEEP, PNP0800): io 0x61
[ 1.021431] spkr0 at pcppi1: PC Speaker
[ 1.021431] wsbell at spkr0 not configured
[ 1.021431] midi0 at pcppi1: PC speaker
[ 1.021431] sysbeep0 at pcppi1
[ 1.021431] com0 at acpi0 (COMA, PNP0501-0): io 0x3f8-0x3ff irq 4
[ 1.021431] com0: ns16550a, 16-byte FIFO
[ 1.021431] pckbc1 at acpi0 (KBD, PNP0303) (kbd port): io 0x60,0x64 irq 1
[ 1.021431] pckbc2 at acpi0 (PS2M, PNP0F13) (aux port): irq 12
[ 1.021431] PMI0 (ACPI000D) at acpi0 not configured
[ 1.021431] acpitz0 at acpi0 (THM0): cpu0
[ 1.021431] acpitz0: levels: critical 31.3 C, passive 9.8 C, passive cooling
[ 1.021431] attimer1: attached to pcppi1
[ 1.021431] pckbd0 at pckbc1 (kbd slot)
[ 1.021431] pckbc1: using irq 1 for kbd slot
[ 1.021431] wskbd0 at pckbd0: console keyboard
[ 1.021431] pms0 at pckbc1 (aux slot)
[ 1.021431] pckbc1: using irq 12 for aux slot
[ 1.021431] wsmouse0 at pms0 mux 0
[ 1.021431] pci0 at mainbus0 bus 0: configuration mode 1
[ 1.021431] pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
[ 1.021431] pchb0 at pci0 dev 0 function 0: Intel Xeon E3-1200 v3 Host Bridge, DRAM (rev. 0x06)
[ 1.021431] ppb0 at pci0 dev 1 function 0: Intel Haswell PCI-E x16 Controller (rev. 0x06)
[ 1.021431] ppb0: PCI Express capability version 2 <Root Port of PCI-E Root Complex> x8 @ 8.0GT/s
[ 1.021431] pci1 at ppb0 bus 4
[ 1.021431] pci1: i/o space, memory space enabled, rd/line, wr/inv ok
[ 1.021431] ppb1 at pci0 dev 1 function 1: Intel Haswell PCI-E x8 Controller (rev. 0x06)
[ 1.021431] ppb1: PCI Express capability version 2 <Root Port of PCI-E Root Complex> x8 @ 8.0GT/s
[ 1.021431] pci2 at ppb1 bus 7
[ 1.021431] pci2: i/o space, memory space enabled, rd/line, wr/inv ok
[ 1.021431] xhci0 at pci0 dev 20 function 0: Intel 8 Series USB xHCI (rev. 0x04)
[ 1.021431] xhci0: 64-bit DMA
[ 1.021431] xhci0: interrupting at msi0 vec 0
[ 1.021431] xhci0: xHCI version 1.0
[ 1.021431] usb0 at xhci0: USB revision 3.0
[ 1.021431] usb1 at xhci0: USB revision 2.0
[ 1.021431] ehci0 at pci0 dev 26 function 0: Intel 8 Series USB EHCI (rev. 0x04)
[ 1.021431] ehci0: 64-bit DMA
[ 1.021431] ehci0: interrupting at ioapic0 pin 21
[ 1.021431] ehci0: BIOS has given up ownership
[ 1.021431] ehci0: EHCI version 1.0
[ 1.021431] ehci0: Using DMA subregion for control data structures
[ 1.021431] usb2 at ehci0: USB revision 2.0
[ 1.021431] ppb2 at pci0 dev 28 function 0: Intel 8 Series PCIe (rev. 0xd4)
[ 1.021431] ppb2: PCI Express capability version 2 <Root Port of PCI-E Root Complex> x1 @ 5.0GT/s
[ 1.021431] pci3 at ppb2 bus 10
[ 1.021431] pci3: i/o space, memory space enabled, rd/line, wr/inv ok
[ 1.021431] ppb3 at pci0 dev 28 function 4: Intel 8 Series PCIe (rev. 0xd4)
[ 1.021431] ppb3: PCI Express capability version 2 <Root Port of PCI-E Root Complex> x1 @ 5.0GT/s
[ 1.021431] pci4 at ppb3 bus 2
[ 1.021431] pci4: i/o space, memory space enabled, rd/line, wr/inv ok
[ 1.021431] ppb4 at pci0 dev 28 function 5: Intel 8 Series PCIe (rev. 0xd4)
[ 1.021431] ppb4: PCI Express capability version 2 <Root Port of PCI-E Root Complex> x1 @ 5.0GT/s
[ 1.021431] pci5 at ppb4 bus 3
[ 1.021431] pci5: i/o space, memory space enabled, rd/line, wr/inv ok
[ 1.021431] bge0 at pci5 dev 0 function 0: Broadcom BCM5720 Gigabit Ethernet
[ 1.021431] bge0: APE firmware NCSI 1.1.15.0
[ 1.021431] bge0: interrupting at msix1 vec 0
[ 1.021431] bge0: HW config 002b10d4, 00006014, 0000aa38, 00000000 00000000
[ 1.021431] bge0: ASIC BCM5720 A0 (0x5720000), Ethernet address a0:1d:48:97:5b:74
[ 1.021431] bge0: setting short Tx thresholds
[ 1.021431] brgphy0 at bge0 phy 1: BCM5720C 1000BASE-T media interface, rev. 0
[ 1.021431] brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
[ 1.021431] bge1 at pci5 dev 0 function 1: Broadcom BCM5720 Gigabit Ethernet
[ 1.021431] bge1: APE firmware NCSI 1.1.15.0
[ 1.021431] bge1: interrupting at msix2 vec 0
[ 1.021431] bge1: HW config 002b10d4, 00006014, 0000aa38, 00000000 00000000
[ 1.021431] bge1: ASIC BCM5720 A0 (0x5720000), Ethernet address a0:1d:48:97:5b:75
[ 1.021431] bge1: setting short Tx thresholds
[ 1.021431] brgphy1 at bge1 phy 2: BCM5720C 1000BASE-T media interface, rev. 0
[ 1.021431] brgphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
[ 1.021431] ppb5 at pci0 dev 28 function 6: Intel 8 Series PCIe (rev. 0xd4)
[ 1.021431] ppb5: PCI Express capability version 2 <Root Port of PCI-E Root Complex> x1 @ 5.0GT/s
[ 1.021431] pci6 at ppb5 bus 13
[ 1.021431] pci6: i/o space, memory space enabled, rd/line, wr/inv ok
[ 1.021431] ppb6 at pci0 dev 28 function 7: Intel 8 Series PCIe (rev. 0xd4)
[ 1.021431] ppb6: PCI Express capability version 2 <Root Port of PCI-E Root Complex> x1 @ 5.0GT/s
[ 1.021431] ppb6: link is x1 @ 2.5GT/s
[ 1.021431] pci7 at ppb6 bus 1
[ 1.021431] pci7: i/o space, memory space enabled, rd/line, wr/inv ok
[ 1.021431] Hewlett-Packard iLO3 Slave (miscellaneous system, revision 0x05) at pci7 dev 0 function 0 not configured
[ 1.021431] vga0 at pci7 dev 0 function 1: Matrox MGA G200eH (rev. 0x00)
[ 1.021431] wsdisplay0 at vga0 kbdmux 1: console (80x25, vt100 emulation), using wskbd0
[ 1.021431] wsmux1: connecting to wsdisplay0
[ 1.021431] drm at vga0 not configured
[ 1.021431] Hewlett-Packard iLO3 Management (miscellaneous system, revision 0x05) at pci7 dev 0 function 2 not configured
[ 1.021431] uhci0 at pci7 dev 0 function 4: Hewlett-Packard iLO3 Virtual USB (rev. 0x02)
[ 1.021431] uhci0: interrupting at msi3 vec 0
[ 1.021431] usb3 at uhci0: USB revision 1.0
[ 1.021431] ehci1 at pci0 dev 29 function 0: Intel 8 Series USB EHCI (rev. 0x04)
[ 1.021431] ehci1: 64-bit DMA
[ 1.021431] ehci1: interrupting at ioapic0 pin 20
[ 1.021431] ehci1: BIOS has given up ownership
[ 1.021431] ehci1: EHCI version 1.0
[ 1.021431] ehci1: Using DMA subregion for control data structures
[ 1.021431] usb4 at ehci1: USB revision 2.0
[ 1.021431] ichlpcib0 at pci0 dev 31 function 0: Intel C222 LPC (rev. 0x04)
[ 1.021431] timecounter: Timecounter "ichlpcib0" frequency 3579545 Hz quality 1000
[ 1.021431] ichlpcib0: 24-bit timer
[ 1.021431] tco0 at ichlpcib0: TCO (watchdog) timer configured.
[ 1.021431] tco0: autoconfiguration error: TCO timer reboot disabled by hardware; hope SMBIOS properly handles it.
[ 1.021431] tco0: Min/Max interval 1/367 seconds
[ 1.021431] ahcisata0 at pci0 dev 31 function 2: Intel 8 Series (desktop) SATA Controller (AHCI) (rev. 0x04)
[ 1.021431] ahcisata0: 64-bit DMA
[ 1.021431] ahcisata0: AHCI revision 1.30, 6 ports, 32 slots, CAP 0xdf30ff45<EMS,PSC,SSC,PMD,ISS=0x3=Gen3,SCLO,SAL,SALP,SSS,SMPS,SNCQ,S64A>
[ 1.021431] ahcisata0: interrupting at msi4 vec 0
[ 1.021431] atabus0 at ahcisata0 channel 0
[ 1.021431] atabus1 at ahcisata0 channel 1
[ 1.021431] atabus2 at ahcisata0 channel 2
[ 1.021431] atabus3 at ahcisata0 channel 3
[ 1.021431] atabus4 at ahcisata0 channel 4
[ 1.021431] atabus5 at ahcisata0 channel 5
[ 1.021431] isa0 at ichlpcib0
[ 1.021431] com1 at isa0 port 0x2f8-0x2ff irq 3: ns16550a, 16-byte FIFO
[ 1.021431] acpicpu0 at cpu0: ACPI CPU
[ 1.021431] acpicpu0: C1: FFH, lat   1 us, pow  1000 mW
[ 1.021431] acpicpu0: C2: FFH, lat  96 us, pow   350 mW
[ 1.021431] coretemp0 at cpu0: thermal sensor, 1 C resolution, Tjmax=100
[ 1.021431] acpicpu1 at cpu1: ACPI CPU
[ 1.021431] coretemp1 at cpu1: thermal sensor, 1 C resolution, Tjmax=100
[ 1.021431] acpicpu2 at cpu2: ACPI CPU
[ 1.021431] coretemp2 at cpu2: thermal sensor, 1 C resolution, Tjmax=100
[ 1.021431] acpicpu3 at cpu3: ACPI CPU
[ 1.021431] coretemp3 at cpu3: thermal sensor, 1 C resolution, Tjmax=100
[ 1.021431] timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
[ 1.021431] timecounter: Timecounter "TSC" frequency 3092842000 Hz quality 3000
[ 1.907097] uhub0 at usb0: NetBSD (0x0000) xHCI root hub (0x0000), class 9/0, rev 3.00/1.00, addr 0
[ 1.907097] uhub0: 2 ports with 2 removable, self powered
[ 1.907097] uhub1 at usb1: NetBSD (0x0000) xHCI root hub (0x0000), class 9/0, rev 2.00/1.00, addr 0
[ 1.907097] uhub1: 10 ports with 10 removable, self powered
[ 1.907097] IPsec: Initialized Security Association Processing.
[ 1.923540] uhub2 at usb2: NetBSD (0x0000) EHCI root hub (0x0000), class 9/0, rev 2.00/1.00, addr 1
[ 1.923540] uhub2: 2 ports with 2 removable, self powered
[ 1.923540] uhub3 at usb3: NetBSD (0x0000) UHCI root hub (0x0000), class 9/0, rev 1.00/1.00, addr 1
[ 1.923540] uhub3: 2 ports with 2 removable, self powered
[ 1.923540] uhub4 at usb4: NetBSD (0x0000) EHCI root hub (0x0000), class 9/0, rev 2.00/1.00, addr 1
[ 1.923540] uhub4: 2 ports with 2 removable, self powered
[ 2.003540] ahcisata0 port 0: device present, speed: 6.0Gb/s
[ 2.003540] ahcisata0 port 4: device present, speed: 1.5Gb/s
[ 2.383539] uhub5 at uhub1 port 3: vendor 0424 (0x0424) product 2660 (0x2660), class 9/0, rev 2.00/8.01, addr 1
[ 2.383539] uhub5: single transaction translator
[ 2.383539] uhub5: 2 ports with 1 removable, self powered
[ 2.993539] uhub6 at uhub4 port 1: vendor 8087 (0x8087) product 8000 (0x8000), class 9/0, rev 2.00/0.04, addr 2
[ 2.993539] uhub6: single transaction translator
[ 2.993539] uhub7 at uhub2 port 1: vendor 8087 (0x8087) product 8008 (0x8008), class 9/0, rev 2.00/0.04, addr 2
[ 2.993539] uhub7: single transaction translator
[ 2.993539] uhub6: 6 ports with 6 removable, self powered
[ 2.993539] uhub7: 4 ports with 4 removable, self powered
[ 3.563538] umass0 at uhub0 port 2 configuration 1 interface 0
[ 3.563538] umass0: USB (0x0781) SanDisk 3.2Gen1 (0x5567), rev 3.20/1.00, addr 2
[ 3.563538] umass0: using SCSI over Bulk-Only
[ 3.563538] scsibus0 at umass0: 2 targets, 1 lun per target
[ 3.573537] sd0 at scsibus0 target 0 lun 0: <USB, SanDisk 3.2Gen1, 1.00> disk removable
[ 3.573537] sd0: 29358 MB, 59648 cyl, 16 head, 63 sec, 512 bytes/sect x 60125184 sectors
[ 3.583536] wd0 at atabus0 drive 0
[ 3.583536] wd0: <ST2000DM001-1CH164>
[ 3.583536] wd0: drive supports 16-sector PIO transfers, LBA48 addressing
[ 3.583536] wd0: 1863 GB, 3876021 cyl, 16 head, 63 sec, 512 bytes/sect x 3907029168 sectors (4096 bytes/physsect;
first aligned sector: 8)
[ 3.593538] wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133), WRITE DMA FUA, NCQ (32 tags)
[ 3.593538] wd0(ahcisata0:0:0): using PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133) (using DMA), NCQ (31 ta
gs)
[ 3.593538] atapibus0 at atabus4: 1 targets
[ 3.603537] cd0 at atapibus0 drive 0: <hp      DVD-RAM GHA3N, KD5DAF43954, WH01> cdrom removable
[ 3.613539] cd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
[ 3.613539] cd0(ahcisata0:4:0): using PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100) (using DMA)
[ 3.633538] uhidev0 at uhub1 port 5 configuration 1 interface 0
[ 3.633538] uhidev0: SEM (0x1a2c) USB Keyboard (0x2124), rev 1.10/1.10, addr 3, iclass 3/1
[ 3.643536] ukbd0 at uhidev0
[ 3.643536] wskbd1 at ukbd0 mux 1
[ 3.643536] wskbd1: connecting to wsdisplay0
[ 3.643536] uhidev1 at uhub1 port 5 configuration 1 interface 1
[ 3.643536] uhidev1: SEM (0x1a2c) USB Keyboard (0x2124), rev 1.10/1.10, addr 3, iclass 3/0
[ 3.643536] uhidev1: 2 report ids
[ 3.643536] uhid0 at uhidev1 reportid 1: input=2, output=0, feature=0
[ 3.643536] uhid1 at uhidev1 reportid 2: input=1, output=0, feature=0
[ 4.123538] uhidev2 at uhub1 port 6 configuration 1 interface 0
[ 4.123538] uhidev2: vendor 275d (0x275d) USB OPTICAL MOUSE (0x0ba6), rev 1.10/1.00, addr 4, iclass 3/1
[ 4.123538] ums0 at uhidev2: 3 buttons and Z dir
[ 4.123538] wsmouse1 at ums0 mux 0
[ 4.603537] uaudio0 at uhub1 port 9 configuration 1 interface 0
[ 4.603537] uaudio0: C-Media INC. (0x0d8c) USB Audio (0x0001), rev 1.10/0.10, addr 5
[ 4.603537] uaudio0: audio rev 1.00
[ 4.603537] audio0 at uaudio0: playback
[ 4.603537] audio0: slinear_le:16 2ch 48000Hz, blk 11520 bytes (60ms) for playback
[ 4.603537] spkr1 at audio0: PC Speaker (synthesized)
[ 4.603537] wsbell at spkr1 not configured
[11.453530] ipmi0: version 32.0 interface KCS iobase 0xca2/0x2 spacing 1
[11.453530] ipmi0: ID 19.2 IPMI 2.0 Available
[11.453530] ipmi0: Additional Chassis FRU SEL SDR Sensor
[11.453530] ipmi0: Manufacturer 0000b Product 200b
[11.453530] ipmi0: Firmware 1.32
[11.453530] swwdog0: software watchdog initialized
[11.493529] WARNING: 1 error while detecting hardware; check system log.
[11.493529] boot device: sd0
[11.493529] root on sd0a dumps on sd0b
[11.503529] root file system type: ffs
[11.503529] kern.module.path=/stand/amd64/10.0/modules
[11.503529] WARNING: NVRAM century is 33 but RTC year is 2024
[24.873516] wsdisplay0: screen 1 added (80x25, vt100 emulation)
[24.873516] wsdisplay0: screen 2 added (80x25, vt100 emulation)
[24.873516] wsdisplay0: screen 3 added (80x25, vt100 emulation)
[24.883516] wsdisplay0: screen 4 added (80x25, vt100 emulation

[J65nko]

Which NetBSD mailing list can I use to report this?

[shep]

I think it is "netbsd-bugs"
http://www.netbsd.org/mailinglists
Apparently there is a utility send-pr(1).

From a personal standpoint, my overall experience with NetBSD is similar to @J65nko. And the few times I tried to report bugs to the mailing lists, they were never addressed. I would be interested to see if reports from a seasoned BSD forum admin are taken seriously.