DaemonForums  

Go Back   DaemonForums > NetBSD > NetBSD Installation and Upgrading

NetBSD Installation and Upgrading Have trouble getting NetBSD on your toaster?

Reply
 
Thread Tools Display Modes
  #1   (View Single Post)  
Old 25th February 2024
J65nko J65nko is offline
Administrator
 
Join Date: May 2008
Location: Budel - the Netherlands
Posts: 4,131
Default NetBSD 10 RC_4 experiences

A few days ago I installed the 4th release candidate of NetBSD on a 32 GB USB 3.0 memory stick.

Install went well and fast. After booting up I installed the Firefox compiled package with pkgin This also went smooth.

I did not have to do anything for the X configuration. But when I started firefox the system became unresponsive (crashed) and seemed to be busy writing a dump file.
Sometimes OpenBSD also shows the same behaviour on this system. Powering off is the only way to regain control.

The system I used is my grumpy HP Proliant server. Linux, FreeBSD and DragonFlyBSD complain that about mixed 32bit and 64bit ACPI data.
The cheap 64bit Xeon CPU has a built-in Matrox VGA processor (mga driver in X Window) and probably uses part of the normal ECC RAM.

NetBSD also mentions problems with the ACPI stuff. It seems to truncate some entries:
The dmesg:
Code:
$ sed -e "s/^\[    /[/" U/dmesg_netbsd10_rc4.txt

[ 1.000000] Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003,
[ 1.000000]     2004, 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013,
[ 1.000000]     2014, 2015, 2016, 2017, 2018, 2019, 2020, 2021, 2022, 2023,
[ 1.000000]     2024
[ 1.000000]     The NetBSD Foundation, Inc.  All rights reserved.
[ 1.000000] Copyright (c) 1982, 1986, 1989, 1991, 1993
[ 1.000000]     The Regents of the University of California.  All rights reserved.

[ 1.000000] NetBSD 10.0_RC4 (GENERIC) #0: Tue Feb  6 12:38:53 UTC 2024
[ 1.000000]     mkrepro@mkrepro.NetBSD.org:/usr/src/sys/arch/amd64/compile/GENERIC
[ 1.000000] total memory = 4061 MB
[ 1.000000] avail memory = 3902 MB
[ 1.000000] timecounter: Timecounters tick every 10.000 msec
[ 1.000000] Kernelized RAIDframe activated
[ 1.000000] timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
[ 1.000004] mainbus0 (root)
[ 1.000004] ACPI: RSDP 0x00000000000F4F00 000024 (v02 HP    )
[ 1.000004] ACPI: XSDT 0x00000000F1DE6400 0000B4 (v01 HP     ProLiant 00000002 ??   0000162E)
[ 1.000004] ACPI: FACP 0x00000000F1DE6540 0000F4 (v03 HP     ProLiant 00000002 ??   0000162E)
[ 1.000004] Firmware Warning (ACPI): 32/64X length mismatch in FADT/Pm1aControlBlock: 16/32 (20221020/tbfadt-640)
[ 1.000004] Firmware Warning (ACPI): 32/64X length mismatch in FADT/Pm2ControlBlock: 8/32 (20221020/tbfadt-640)
[ 1.000004] Firmware Warning (ACPI): Invalid length for FADT/Pm1aControlBlock: 32, using default 16 (20221020/tbfa
dt-742)
[ 1.000004] Firmware Warning (ACPI): Invalid length for FADT/Pm2ControlBlock: 32, using default 8 (20221020/tbfadt
-742)
[ 1.000004] ACPI: DSDT 0x00000000F1DE6640 002A13 (v01 HP     DSDT     00000001 INTL 20030228)
[ 1.000004] ACPI: FACS 0x00000000F1DE4140 000040
[ 1.000004] ACPI: SPCR 0x00000000F1DE4180 000050 (v01 HP     SPCRRBSU 00000001 ??   0000162E)
[ 1.000004] ACPI: MCFG 0x00000000F1DE4200 00003C (v01 HP     ProLiant 00000001      00000000)
[ 1.000004] ACPI: HPET 0x00000000F1DE4240 000038 (v01 HP     ProLiant 00000002 ??   0000162E)
[ 1.000004] ACPI: FFFF 0x00000000F1DE4280 000064 (v02 HP     ProLiant 00000002 ??   0000162E)
[ 1.000004] ACPI: SPMI 0x00000000F1DE4300 000040 (v05 HP     ProLiant 00000001 ??   0000162E)
[ 1.000004] ACPI: ERST 0x00000000F1DE4340 000230 (v01 HP     ProLiant 00000001 ??   0000162E)
[ 1.000004] ACPI: APIC 0x00000000F1DE4580 000252 (v01 HP     ProLiant 00000002      00000000)
[ 1.000004] ACPI: FFFF 0x00000000F1DE4800 000176 (v01 HP     ProLiant 00000001 ??   0000162E)
[ 1.000004] ACPI: BERT 0x00000000F1DE4980 000030 (v01 HP     ProLiant 00000001 ??   0000162E)
[ 1.000004] ACPI: HEST 0x00000000F1DE49C0 0000BC (v01 HP     ProLiant 00000001 ??   0000162E)
[ 1.000004] ACPI: DMAR 0x00000000F1DE4A80 00030E (v01 HP     ProLiant 00000001 ??   0000162E)
[ 1.000004] ACPI: FFFF 0x00000000F1DE63C0 00002D (v01 HP     ProLiant 00000001      00000000)
[ 1.000004] ACPI: SSDT 0x00000000F1DE9080 000137 (v03 HP     CRSPCI0  00000002 HP   00000001)
[ 1.000004] ACPI: SSDT 0x00000000F1DE91C0 000573 (v03 HP     riser0   00000002 INTL 20030228)
[ 1.000004] ACPI: SSDT 0x00000000F1DE9740 0001E1 (v01 HP     pcc      00000001 INTL 20090625)
[ 1.000004] ACPI: SSDT 0x00000000F1DE9940 000377 (v01 HP     pmab     00000001 INTL 20090625)
[ 1.000004] ACPI: SSDT 0x00000000F1DE9CC0 0009E4 (v01 INTEL  PPM RCM  80000001 INTL 20061109)
[ 1.000004] ACPI: 6 ACPI AML tables successfully acquired and loaded
[ 1.000004] ioapic0 at mainbus0 apid 8: pa 0xfec00000, version 0x20, 24 pins
[ 1.000004] x2APIC available but disabled by DMAR table
[ 1.000004] cpu0 at mainbus0 apid 0
[ 1.000004] cpu0: Use lfence to serialize rdtsc
[ 1.000004] cpu0: Intel(R) Xeon(R) CPU E3-1220 v3 @ 3.10GHz, id 0x306c3
[ 1.000004] cpu0: node 0, package 0, core 0, smt 0
[ 1.000004] cpu1 at mainbus0 apid 2
[ 1.000004] cpu1: Intel(R) Xeon(R) CPU E3-1220 v3 @ 3.10GHz, id 0x306c3
[ 1.000004] cpu1: node 0, package 0, core 1, smt 0
[ 1.000004] cpu2 at mainbus0 apid 4
[ 1.000004] cpu2: Intel(R) Xeon(R) CPU E3-1220 v3 @ 3.10GHz, id 0x306c3
[ 1.000004] cpu2: node 0, package 0, core 2, smt 0
[ 1.000004] cpu3 at mainbus0 apid 6
[ 1.000004] cpu3: Intel(R) Xeon(R) CPU E3-1220 v3 @ 3.10GHz, id 0x306c3
[ 1.000004] cpu3: node 0, package 0, core 3, smt 0
[ 1.000004] acpi0 at mainbus0: Intel ACPICA 20221020
[ 1.000004] acpi0: X/RSDT: OemId <HP    ,ProLiant,00000002>, AslId <  <2147483602>^D,0000162e>
[ 1.000004] acpi0: MCFG: segment 0, bus 0-63, address 0x00000000f4000000
[ 1.000004] acpi0: SCI interrupting at int 9
[ 1.000004] acpi0: fixed power button present
[ 1.000004] timecounter: Timecounter "ACPI-Fast" frequency 3579545 Hz quality 1000
[ 1.021219] hpet0 at acpi0: high precision event timer (mem 0xfed00000-0xfed00400)
[ 1.021219] timecounter: Timecounter "hpet0" frequency 14318180 Hz quality 2000
[ 1.021431] ipmi_acpi0 at acpi0 (MI0, IPI0001-0): io 0xca2-0xca3
[ 1.021431] ipmi0 at ipmi_acpi0
[ 1.021431] attimer1 at acpi0 (TIME, PNP0100): io 0x40-0x43 irq 0
[ 1.021431] pcppi1 at acpi0 (BEEP, PNP0800): io 0x61
[ 1.021431] spkr0 at pcppi1: PC Speaker
[ 1.021431] wsbell at spkr0 not configured
[ 1.021431] midi0 at pcppi1: PC speaker
[ 1.021431] sysbeep0 at pcppi1
[ 1.021431] com0 at acpi0 (COMA, PNP0501-0): io 0x3f8-0x3ff irq 4
[ 1.021431] com0: ns16550a, 16-byte FIFO
[ 1.021431] pckbc1 at acpi0 (KBD, PNP0303) (kbd port): io 0x60,0x64 irq 1
[ 1.021431] pckbc2 at acpi0 (PS2M, PNP0F13) (aux port): irq 12
[ 1.021431] PMI0 (ACPI000D) at acpi0 not configured
[ 1.021431] acpitz0 at acpi0 (THM0): cpu0
[ 1.021431] acpitz0: levels: critical 31.3 C, passive 9.8 C, passive cooling
[ 1.021431] attimer1: attached to pcppi1
[ 1.021431] pckbd0 at pckbc1 (kbd slot)
[ 1.021431] pckbc1: using irq 1 for kbd slot
[ 1.021431] wskbd0 at pckbd0: console keyboard
[ 1.021431] pms0 at pckbc1 (aux slot)
[ 1.021431] pckbc1: using irq 12 for aux slot
[ 1.021431] wsmouse0 at pms0 mux 0
[ 1.021431] pci0 at mainbus0 bus 0: configuration mode 1
[ 1.021431] pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
[ 1.021431] pchb0 at pci0 dev 0 function 0: Intel Xeon E3-1200 v3 Host Bridge, DRAM (rev. 0x06)
[ 1.021431] ppb0 at pci0 dev 1 function 0: Intel Haswell PCI-E x16 Controller (rev. 0x06)
[ 1.021431] ppb0: PCI Express capability version 2 <Root Port of PCI-E Root Complex> x8 @ 8.0GT/s
[ 1.021431] pci1 at ppb0 bus 4
[ 1.021431] pci1: i/o space, memory space enabled, rd/line, wr/inv ok
[ 1.021431] ppb1 at pci0 dev 1 function 1: Intel Haswell PCI-E x8 Controller (rev. 0x06)
[ 1.021431] ppb1: PCI Express capability version 2 <Root Port of PCI-E Root Complex> x8 @ 8.0GT/s
[ 1.021431] pci2 at ppb1 bus 7
[ 1.021431] pci2: i/o space, memory space enabled, rd/line, wr/inv ok
[ 1.021431] xhci0 at pci0 dev 20 function 0: Intel 8 Series USB xHCI (rev. 0x04)
[ 1.021431] xhci0: 64-bit DMA
[ 1.021431] xhci0: interrupting at msi0 vec 0
[ 1.021431] xhci0: xHCI version 1.0
[ 1.021431] usb0 at xhci0: USB revision 3.0
[ 1.021431] usb1 at xhci0: USB revision 2.0
[ 1.021431] ehci0 at pci0 dev 26 function 0: Intel 8 Series USB EHCI (rev. 0x04)
[ 1.021431] ehci0: 64-bit DMA
[ 1.021431] ehci0: interrupting at ioapic0 pin 21
[ 1.021431] ehci0: BIOS has given up ownership
[ 1.021431] ehci0: EHCI version 1.0
[ 1.021431] ehci0: Using DMA subregion for control data structures
[ 1.021431] usb2 at ehci0: USB revision 2.0
[ 1.021431] ppb2 at pci0 dev 28 function 0: Intel 8 Series PCIe (rev. 0xd4)
[ 1.021431] ppb2: PCI Express capability version 2 <Root Port of PCI-E Root Complex> x1 @ 5.0GT/s
[ 1.021431] pci3 at ppb2 bus 10
[ 1.021431] pci3: i/o space, memory space enabled, rd/line, wr/inv ok
[ 1.021431] ppb3 at pci0 dev 28 function 4: Intel 8 Series PCIe (rev. 0xd4)
[ 1.021431] ppb3: PCI Express capability version 2 <Root Port of PCI-E Root Complex> x1 @ 5.0GT/s
[ 1.021431] pci4 at ppb3 bus 2
[ 1.021431] pci4: i/o space, memory space enabled, rd/line, wr/inv ok
[ 1.021431] ppb4 at pci0 dev 28 function 5: Intel 8 Series PCIe (rev. 0xd4)
[ 1.021431] ppb4: PCI Express capability version 2 <Root Port of PCI-E Root Complex> x1 @ 5.0GT/s
[ 1.021431] pci5 at ppb4 bus 3
[ 1.021431] pci5: i/o space, memory space enabled, rd/line, wr/inv ok
[ 1.021431] bge0 at pci5 dev 0 function 0: Broadcom BCM5720 Gigabit Ethernet
[ 1.021431] bge0: APE firmware NCSI 1.1.15.0
[ 1.021431] bge0: interrupting at msix1 vec 0
[ 1.021431] bge0: HW config 002b10d4, 00006014, 0000aa38, 00000000 00000000
[ 1.021431] bge0: ASIC BCM5720 A0 (0x5720000), Ethernet address a0:1d:48:97:5b:74
[ 1.021431] bge0: setting short Tx thresholds
[ 1.021431] brgphy0 at bge0 phy 1: BCM5720C 1000BASE-T media interface, rev. 0
[ 1.021431] brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
[ 1.021431] bge1 at pci5 dev 0 function 1: Broadcom BCM5720 Gigabit Ethernet
[ 1.021431] bge1: APE firmware NCSI 1.1.15.0
[ 1.021431] bge1: interrupting at msix2 vec 0
[ 1.021431] bge1: HW config 002b10d4, 00006014, 0000aa38, 00000000 00000000
[ 1.021431] bge1: ASIC BCM5720 A0 (0x5720000), Ethernet address a0:1d:48:97:5b:75
[ 1.021431] bge1: setting short Tx thresholds
[ 1.021431] brgphy1 at bge1 phy 2: BCM5720C 1000BASE-T media interface, rev. 0
[ 1.021431] brgphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
[ 1.021431] ppb5 at pci0 dev 28 function 6: Intel 8 Series PCIe (rev. 0xd4)
[ 1.021431] ppb5: PCI Express capability version 2 <Root Port of PCI-E Root Complex> x1 @ 5.0GT/s
[ 1.021431] pci6 at ppb5 bus 13
[ 1.021431] pci6: i/o space, memory space enabled, rd/line, wr/inv ok
[ 1.021431] ppb6 at pci0 dev 28 function 7: Intel 8 Series PCIe (rev. 0xd4)
[ 1.021431] ppb6: PCI Express capability version 2 <Root Port of PCI-E Root Complex> x1 @ 5.0GT/s
[ 1.021431] ppb6: link is x1 @ 2.5GT/s
[ 1.021431] pci7 at ppb6 bus 1
[ 1.021431] pci7: i/o space, memory space enabled, rd/line, wr/inv ok
[ 1.021431] Hewlett-Packard iLO3 Slave (miscellaneous system, revision 0x05) at pci7 dev 0 function 0 not configured
[ 1.021431] vga0 at pci7 dev 0 function 1: Matrox MGA G200eH (rev. 0x00)
[ 1.021431] wsdisplay0 at vga0 kbdmux 1: console (80x25, vt100 emulation), using wskbd0
[ 1.021431] wsmux1: connecting to wsdisplay0
[ 1.021431] drm at vga0 not configured
[ 1.021431] Hewlett-Packard iLO3 Management (miscellaneous system, revision 0x05) at pci7 dev 0 function 2 not configured
[ 1.021431] uhci0 at pci7 dev 0 function 4: Hewlett-Packard iLO3 Virtual USB (rev. 0x02)
[ 1.021431] uhci0: interrupting at msi3 vec 0
[ 1.021431] usb3 at uhci0: USB revision 1.0
[ 1.021431] ehci1 at pci0 dev 29 function 0: Intel 8 Series USB EHCI (rev. 0x04)
[ 1.021431] ehci1: 64-bit DMA
[ 1.021431] ehci1: interrupting at ioapic0 pin 20
[ 1.021431] ehci1: BIOS has given up ownership
[ 1.021431] ehci1: EHCI version 1.0
[ 1.021431] ehci1: Using DMA subregion for control data structures
[ 1.021431] usb4 at ehci1: USB revision 2.0
[ 1.021431] ichlpcib0 at pci0 dev 31 function 0: Intel C222 LPC (rev. 0x04)
[ 1.021431] timecounter: Timecounter "ichlpcib0" frequency 3579545 Hz quality 1000
[ 1.021431] ichlpcib0: 24-bit timer
[ 1.021431] tco0 at ichlpcib0: TCO (watchdog) timer configured.
[ 1.021431] tco0: autoconfiguration error: TCO timer reboot disabled by hardware; hope SMBIOS properly handles it.
[ 1.021431] tco0: Min/Max interval 1/367 seconds
[ 1.021431] ahcisata0 at pci0 dev 31 function 2: Intel 8 Series (desktop) SATA Controller (AHCI) (rev. 0x04)
[ 1.021431] ahcisata0: 64-bit DMA
[ 1.021431] ahcisata0: AHCI revision 1.30, 6 ports, 32 slots, CAP 0xdf30ff45<EMS,PSC,SSC,PMD,ISS=0x3=Gen3,SCLO,SAL,SALP,SSS,SMPS,SNCQ,S64A>
[ 1.021431] ahcisata0: interrupting at msi4 vec 0
[ 1.021431] atabus0 at ahcisata0 channel 0
[ 1.021431] atabus1 at ahcisata0 channel 1
[ 1.021431] atabus2 at ahcisata0 channel 2
[ 1.021431] atabus3 at ahcisata0 channel 3
[ 1.021431] atabus4 at ahcisata0 channel 4
[ 1.021431] atabus5 at ahcisata0 channel 5
[ 1.021431] isa0 at ichlpcib0
[ 1.021431] com1 at isa0 port 0x2f8-0x2ff irq 3: ns16550a, 16-byte FIFO
[ 1.021431] acpicpu0 at cpu0: ACPI CPU
[ 1.021431] acpicpu0: C1: FFH, lat   1 us, pow  1000 mW
[ 1.021431] acpicpu0: C2: FFH, lat  96 us, pow   350 mW
[ 1.021431] coretemp0 at cpu0: thermal sensor, 1 C resolution, Tjmax=100
[ 1.021431] acpicpu1 at cpu1: ACPI CPU
[ 1.021431] coretemp1 at cpu1: thermal sensor, 1 C resolution, Tjmax=100
[ 1.021431] acpicpu2 at cpu2: ACPI CPU
[ 1.021431] coretemp2 at cpu2: thermal sensor, 1 C resolution, Tjmax=100
[ 1.021431] acpicpu3 at cpu3: ACPI CPU
[ 1.021431] coretemp3 at cpu3: thermal sensor, 1 C resolution, Tjmax=100
[ 1.021431] timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
[ 1.021431] timecounter: Timecounter "TSC" frequency 3092842000 Hz quality 3000
[ 1.907097] uhub0 at usb0: NetBSD (0x0000) xHCI root hub (0x0000), class 9/0, rev 3.00/1.00, addr 0
[ 1.907097] uhub0: 2 ports with 2 removable, self powered
[ 1.907097] uhub1 at usb1: NetBSD (0x0000) xHCI root hub (0x0000), class 9/0, rev 2.00/1.00, addr 0
[ 1.907097] uhub1: 10 ports with 10 removable, self powered
[ 1.907097] IPsec: Initialized Security Association Processing.
[ 1.923540] uhub2 at usb2: NetBSD (0x0000) EHCI root hub (0x0000), class 9/0, rev 2.00/1.00, addr 1
[ 1.923540] uhub2: 2 ports with 2 removable, self powered
[ 1.923540] uhub3 at usb3: NetBSD (0x0000) UHCI root hub (0x0000), class 9/0, rev 1.00/1.00, addr 1
[ 1.923540] uhub3: 2 ports with 2 removable, self powered
[ 1.923540] uhub4 at usb4: NetBSD (0x0000) EHCI root hub (0x0000), class 9/0, rev 2.00/1.00, addr 1
[ 1.923540] uhub4: 2 ports with 2 removable, self powered
[ 2.003540] ahcisata0 port 0: device present, speed: 6.0Gb/s
[ 2.003540] ahcisata0 port 4: device present, speed: 1.5Gb/s
[ 2.383539] uhub5 at uhub1 port 3: vendor 0424 (0x0424) product 2660 (0x2660), class 9/0, rev 2.00/8.01, addr 1
[ 2.383539] uhub5: single transaction translator
[ 2.383539] uhub5: 2 ports with 1 removable, self powered
[ 2.993539] uhub6 at uhub4 port 1: vendor 8087 (0x8087) product 8000 (0x8000), class 9/0, rev 2.00/0.04, addr 2
[ 2.993539] uhub6: single transaction translator
[ 2.993539] uhub7 at uhub2 port 1: vendor 8087 (0x8087) product 8008 (0x8008), class 9/0, rev 2.00/0.04, addr 2
[ 2.993539] uhub7: single transaction translator
[ 2.993539] uhub6: 6 ports with 6 removable, self powered
[ 2.993539] uhub7: 4 ports with 4 removable, self powered
[ 3.563538] umass0 at uhub0 port 2 configuration 1 interface 0
[ 3.563538] umass0: USB (0x0781) SanDisk 3.2Gen1 (0x5567), rev 3.20/1.00, addr 2
[ 3.563538] umass0: using SCSI over Bulk-Only
[ 3.563538] scsibus0 at umass0: 2 targets, 1 lun per target
[ 3.573537] sd0 at scsibus0 target 0 lun 0: <USB, SanDisk 3.2Gen1, 1.00> disk removable
[ 3.573537] sd0: 29358 MB, 59648 cyl, 16 head, 63 sec, 512 bytes/sect x 60125184 sectors
[ 3.583536] wd0 at atabus0 drive 0
[ 3.583536] wd0: <ST2000DM001-1CH164>
[ 3.583536] wd0: drive supports 16-sector PIO transfers, LBA48 addressing
[ 3.583536] wd0: 1863 GB, 3876021 cyl, 16 head, 63 sec, 512 bytes/sect x 3907029168 sectors (4096 bytes/physsect;
first aligned sector: 8)
[ 3.593538] wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133), WRITE DMA FUA, NCQ (32 tags)
[ 3.593538] wd0(ahcisata0:0:0): using PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133) (using DMA), NCQ (31 ta
gs)
[ 3.593538] atapibus0 at atabus4: 1 targets
[ 3.603537] cd0 at atapibus0 drive 0: <hp      DVD-RAM GHA3N, KD5DAF43954, WH01> cdrom removable
[ 3.613539] cd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
[ 3.613539] cd0(ahcisata0:4:0): using PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100) (using DMA)
[ 3.633538] uhidev0 at uhub1 port 5 configuration 1 interface 0
[ 3.633538] uhidev0: SEM (0x1a2c) USB Keyboard (0x2124), rev 1.10/1.10, addr 3, iclass 3/1
[ 3.643536] ukbd0 at uhidev0
[ 3.643536] wskbd1 at ukbd0 mux 1
[ 3.643536] wskbd1: connecting to wsdisplay0
[ 3.643536] uhidev1 at uhub1 port 5 configuration 1 interface 1
[ 3.643536] uhidev1: SEM (0x1a2c) USB Keyboard (0x2124), rev 1.10/1.10, addr 3, iclass 3/0
[ 3.643536] uhidev1: 2 report ids
[ 3.643536] uhid0 at uhidev1 reportid 1: input=2, output=0, feature=0
[ 3.643536] uhid1 at uhidev1 reportid 2: input=1, output=0, feature=0
[ 4.123538] uhidev2 at uhub1 port 6 configuration 1 interface 0
[ 4.123538] uhidev2: vendor 275d (0x275d) USB OPTICAL MOUSE (0x0ba6), rev 1.10/1.00, addr 4, iclass 3/1
[ 4.123538] ums0 at uhidev2: 3 buttons and Z dir
[ 4.123538] wsmouse1 at ums0 mux 0
[ 4.603537] uaudio0 at uhub1 port 9 configuration 1 interface 0
[ 4.603537] uaudio0: C-Media INC. (0x0d8c) USB Audio (0x0001), rev 1.10/0.10, addr 5
[ 4.603537] uaudio0: audio rev 1.00
[ 4.603537] audio0 at uaudio0: playback
[ 4.603537] audio0: slinear_le:16 2ch 48000Hz, blk 11520 bytes (60ms) for playback
[ 4.603537] spkr1 at audio0: PC Speaker (synthesized)
[ 4.603537] wsbell at spkr1 not configured
[11.453530] ipmi0: version 32.0 interface KCS iobase 0xca2/0x2 spacing 1
[11.453530] ipmi0: ID 19.2 IPMI 2.0 Available
[11.453530] ipmi0: Additional Chassis FRU SEL SDR Sensor
[11.453530] ipmi0: Manufacturer 0000b Product 200b
[11.453530] ipmi0: Firmware 1.32
[11.453530] swwdog0: software watchdog initialized
[11.493529] WARNING: 1 error while detecting hardware; check system log.
[11.493529] boot device: sd0
[11.493529] root on sd0a dumps on sd0b
[11.503529] root file system type: ffs
[11.503529] kern.module.path=/stand/amd64/10.0/modules
[11.503529] WARNING: NVRAM century is 33 but RTC year is 2024
[24.873516] wsdisplay0: screen 1 added (80x25, vt100 emulation)
[24.873516] wsdisplay0: screen 2 added (80x25, vt100 emulation)
[24.873516] wsdisplay0: screen 3 added (80x25, vt100 emulation)
[24.883516] wsdisplay0: screen 4 added (80x25, vt100 emulation
__________________
You don't need to be a genius to debug a pf.conf firewall ruleset, you just need the guts to run tcpdump
Reply With Quote
  #2   (View Single Post)  
Old 4th March 2024
J65nko J65nko is offline
Administrator
 
Join Date: May 2008
Location: Budel - the Netherlands
Posts: 4,131
Default

Which NetBSD mailing list can I use to report this?
__________________
You don't need to be a genius to debug a pf.conf firewall ruleset, you just need the guts to run tcpdump
Reply With Quote
  #3   (View Single Post)  
Old 4th March 2024
shep shep is offline
Real Name: Scott
Arp Constable
 
Join Date: May 2008
Location: Dry and Dusty
Posts: 1,507
Default

I think it is "netbsd-bugs"
http://www.netbsd.org/mailinglists
Apparently there is a utility send-pr(1).

From a personal standpoint, my overall experience with NetBSD is similar to @J65nko. And the few times I tried to report bugs to the mailing lists, they were never addressed. I would be interested to see if reports from a seasoned BSD forum admin are taken seriously.

Last edited by shep; 9th March 2024 at 02:53 AM.
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
softraid: your experiences and suggestions? dogeoj OpenBSD General 5 9th April 2019 07:06 PM
Wine: Your Experiences ninjatux Off-Topic 10 4th June 2013 12:48 PM
Soekris experiences Carpetsmoker General Hardware 42 21st August 2009 01:52 PM
NetBSD 4.0: your experiences with binary / source pkgs? anomie NetBSD Package System (pkgsrc) 10 23rd December 2008 08:12 PM
HDD formatted UFS under AMD64 experiences weirdness under I386 Gemini FreeBSD General 4 9th December 2008 05:27 AM


All times are GMT. The time now is 02:32 AM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Content copyright © 2007-2010, the authors
Daemon image copyright ©1988, Marshall Kirk McKusick