DaemonForums  

Go Back   DaemonForums > OpenBSD > OpenBSD Installation and Upgrading
Reload this Page Wifi trouble - worked during install, never again
FAQ Search Today's Posts Mark Forums Read

OpenBSD Installation and Upgrading Installing and upgrading OpenBSD.

Reply
 
Thread Tools Display Modes
  #1   (View Single Post)  
Old 27th December 2009
RadioKJ RadioKJ is offline
New User
  
Join Date: Dec 2009
Posts: 8
Question Wifi trouble - worked during install, never again
I'm having some trouble getting wireless working on 4.6. I'm using a D-Link DWA-130 device (Ralink RT2870) which is listed as supported. When I do "ifconfig run0 scan" it shows my network and all others in the area without trouble. But when I try to connect:

Quote:
ifconfig run0 nwid MYNETWORK nwkey 0xMYKEYTRIPLECHECKED
dhclient run0
DHCPDISCOVER on run0 to 255.255.255.255 port 67 interval 5
DHCPDISCOVER on run0 to 255.255.255.255 port 67 interval 14
...
No DHCPOFFERS received.
Doing exactly this worked fine while installing and I was able to connect, but it ceases to work after install. I can only scan and never connect.
Reply With Quote
  #2   (View Single Post)  
Old 27th December 2009
There0 There0 is offline
./dev/null
  
Join Date: Jul 2008
Posts: 170
Default
Hi there RadioKJ, it would be to your benefit to post the results of your dmesg and ifconfig -a command, we on the other end of your post cannot tell as much.
__________________
The more you learn, the more you realize how little you know ....
Reply With Quote
  #3   (View Single Post)  
Old 28th December 2009
RadioKJ RadioKJ is offline
New User
  
Join Date: Dec 2009
Posts: 8
Default
ifconfig:
Code:
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 33152
	priority: 0
	groups: lo
	inet 127.0.0.1 netmask 0xff000000
	inet6 ::1 prefixlen 128
	inet6 fe80::1%lo0 prefixlen 64 scopeid 0x3
msk0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> mtu 1500
	lladdr 00:1f:e2:3c:5e:e3
	priority: 0
	media: Ethernet autoselect (none)
	status: no carrier
enc0: flags=0<> mtu 1536
	priority: 0
run0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
	lladdr 00:22:b0:0d:5d:82
	priority: 4
	groups: wlan
	media: IEEE802.11 autoselect (DS1 mode 11g)
	status: active
	ieee80211: nwid VERIFIED chan 11 bssid 00:14:bf:9e:8a:7e 46dB nwkey 0xVERIFIED
	inet6 fe80::222:b0ff:fe0d:5d82%run0 prefixlen 64 scopeid 0x4
pflog0: flags=141<UP,RUNNING,PROMISC> mtu 33152
	priority: 0
	groups: pflog
dmesg:
Code:
OpenBSD 4.6 (GENERIC.MP) #81: Thu Jul  9 21:26:19 MDT 2009
    deraadt@amd64.openbsd.org:/usr/src/s...ile/GENERIC.MP
real mem = 1877540864 (1790MB)
avail mem = 1809547264 (1725MB)
mainbus0 at root
bios0 at mainbus0: SMBIOS rev. 2.5 @ 0x9f400 (30 entries)
bios0: vendor American Megatrends Inc. version "R03-B0" date 05/07/2008
bios0: Acer Aspire M1201
acpi0 at bios0: rev 0
acpi0: tables DSDT FACP APIC MCFG SLIC OEMB HPET ASF! AWMI SSDT
acpi0: wakeup devices PCE2(S4) PCE3(S4) PCE4(S4) PCE5(S4) PCE6(S4) PCE7(S4) SBAZ(S4) UAR1(S3) UAR2(S3) PS2K(S3) PS2M(S3) P0PC(S4) UHC1(S3) UHC2(S3) UHC3(S3) USB4(S3) UHC5(S3) UHC6(S3) UHC7(S3) PWRB(S3)
acpitimer0 at acpi0: 3579545 Hz, 32 bits
acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat
cpu0 at mainbus0: apid 0 (boot processor)
cpu0: AMD Athlon(tm) 64 X2 Dual Core Processor 4400+, 2299.40 MHz
cpu0: FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,MMX,FXSR,SSE,SSE2,HTT,SSE3,CX16,NXE,MMXX,FFXSR,LONG,3DNOW2,3DNOW
cpu0: 64KB 64b/line 2-way I-cache, 64KB 64b/line 2-way D-cache, 512KB 64b/line 16-way L2 cache
cpu0: ITLB 32 4KB entries fully associative, 8 4MB entries fully associative
cpu0: DTLB 32 4KB entries fully associative, 8 4MB entries fully associative
cpu0: apic clock running at 199MHz
cpu1 at mainbus0: apid 1 (application processor)
cpu1: AMD Athlon(tm) 64 X2 Dual Core Processor 4400+, 2299.12 MHz
cpu1: FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,MMX,FXSR,SSE,SSE2,HTT,SSE3,CX16,NXE,MMXX,FFXSR,LONG,3DNOW2,3DNOW
cpu1: 64KB 64b/line 2-way I-cache, 64KB 64b/line 2-way D-cache, 512KB 64b/line 16-way L2 cache
cpu1: ITLB 32 4KB entries fully associative, 8 4MB entries fully associative
cpu1: DTLB 32 4KB entries fully associative, 8 4MB entries fully associative
ioapic0 at mainbus0 apid 2 pa 0xfec00000, version 21, 24 pins
ioapic0: misconfigured as apic 0, remapped to apid 2
acpihpet0 at acpi0: 14318180 Hz
acpiprt0 at acpi0: bus 0 (PCI0)
acpiprt1 at acpi0: bus 1 (P0P1)
acpiprt2 at acpi0: bus -1 (PCE2)
acpiprt3 at acpi0: bus -1 (PCE3)
acpiprt4 at acpi0: bus 2 (PCE4)
acpiprt5 at acpi0: bus 3 (PCE5)
acpiprt6 at acpi0: bus 4 (PCE6)
acpiprt7 at acpi0: bus -1 (PCE7)
acpiprt8 at acpi0: bus 5 (P0PC)
acpicpu0 at acpi0: PSS
acpicpu1 at acpi0: PSS
acpitz0 at acpi0: critical temperature 90 degC
acpibtn0 at acpi0: PWRB
cpu0: PowerNow! K8 2299 MHz: speeds: 2300 2200 2000 1800 1000 MHz
pci0 at mainbus0 bus 0
pchb0 at pci0 dev 0 function 0 "ATI RS740 Host" rev 0x00
ppb0 at pci0 dev 1 function 0 "ATI RS690 PCIE" rev 0x00
pci1 at ppb0 bus 1
vga1 at pci1 dev 5 function 0 "ATI Radeon 2100" rev 0x00
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
ppb1 at pci0 dev 4 function 0 vendor "ATI", unknown product 0x7914 rev 0x00
pci2 at ppb1 bus 2
vendor "Conexant", unknown product 0x8880 (class multimedia subclass video, rev 0x0f) at pci2 dev 0 function 0 not configured
ppb2 at pci0 dev 5 function 0 "ATI RS690 PCIE" rev 0x00
pci3 at ppb2 bus 3
mskc0 at pci3 dev 0 function 0 "Marvell Yukon 88E8071" rev 0x16, Yukon-2 Extreme rev. B0 (0x2): apic 2 int 17 (irq 11)
msk0 at mskc0 port A: address 00:1f:e2:3c:5e:e3
eephy0 at msk0 phy 0: 88E1149 Gigabit PHY, rev. 1
ppb3 at pci0 dev 6 function 0 "ATI RS690 PCIE" rev 0x00
pci4 at ppb3 bus 4
"JMicron FireWire" rev 0x00 at pci4 dev 0 function 0 not configured
pciide0 at pci0 dev 17 function 0 "ATI SBx00 SATA" rev 0x00: DMA (unsupported), channel 0 configured to native-PCI, channel 1 configured to native-PCI
pciide0: using apic 2 int 22 (irq 10) for native-PCI interrupt
wd0 at pciide0 channel 0 drive 0: <WDC WD3200AAJS-22B4A0>
wd0: 16-sector PIO, LBA48, 305245MB, 625142448 sectors
atapiscsi0 at pciide0 channel 1 drive 0
scsibus0 at atapiscsi0: 2 targets
cd0 at scsibus0 targ 0 lun 0: <HL-DT-ST, DVDRAM GH15F, EG00> ATAPI 5/cdrom removable
ohci0 at pci0 dev 18 function 0 "ATI SB700 USB" rev 0x00: apic 2 int 16 (irq 11), version 1.0, legacy support
ohci1 at pci0 dev 18 function 1 "ATI SB700 USB" rev 0x00: apic 2 int 16 (irq 11), version 1.0, legacy support
ehci0 at pci0 dev 18 function 2 "ATI SB700 USB2" rev 0x00: apic 2 int 17 (irq 11)
usb0 at ehci0: USB revision 2.0
uhub0 at usb0 "ATI EHCI root hub" rev 2.00/1.00 addr 1
ohci2 at pci0 dev 19 function 0 "ATI SB700 USB" rev 0x00: apic 2 int 18 (irq 10), version 1.0, legacy support
ohci3 at pci0 dev 19 function 1 "ATI SB700 USB" rev 0x00: apic 2 int 18 (irq 10), version 1.0, legacy support
ehci1 at pci0 dev 19 function 2 "ATI SB700 USB2" rev 0x00: apic 2 int 19 (irq 10)
usb1 at ehci1: USB revision 2.0
uhub1 at usb1 "ATI EHCI root hub" rev 2.00/1.00 addr 1
piixpm0 at pci0 dev 20 function 0 "ATI SBx00 SMBus" rev 0x3a: SMI
iic0 at piixpm0
spdmem0 at iic0 addr 0x50: 1GB DDR2 SDRAM non-parity PC2-5300CL5
spdmem1 at iic0 addr 0x51: 1GB DDR2 SDRAM non-parity PC2-5300CL5
pciide1 at pci0 dev 20 function 1 "ATI SB700 IDE" rev 0x00: DMA, channel 0 configured to compatibility, channel 1 configured to compatibility
azalia0 at pci0 dev 20 function 2 "ATI SBx00 HD Audio" rev 0x00: apic 2 int 16 (irq 11)
azalia0: codecs: Realtek ALC888
audio0 at azalia0
pcib0 at pci0 dev 20 function 3 "ATI SB700 ISA" rev 0x00
ppb4 at pci0 dev 20 function 4 "ATI SB600 PCI" rev 0x00
pci5 at ppb4 bus 5
ohci4 at pci0 dev 20 function 5 "ATI SB700 USB" rev 0x00: apic 2 int 18 (irq 10), version 1.0, legacy support
pchb1 at pci0 dev 24 function 0 "AMD AMD64 0Fh HyperTransport" rev 0x00
pchb2 at pci0 dev 24 function 1 "AMD AMD64 0Fh Address Map" rev 0x00
pchb3 at pci0 dev 24 function 2 "AMD AMD64 0Fh DRAM Cfg" rev 0x00
kate0 at pci0 dev 24 function 3 "AMD AMD64 0Fh Misc Cfg" rev 0x00: core rev BH-G2
usb2 at ohci0: USB revision 1.0
uhub2 at usb2 "ATI OHCI root hub" rev 1.00/1.00 addr 1
usb3 at ohci1: USB revision 1.0
uhub3 at usb3 "ATI OHCI root hub" rev 1.00/1.00 addr 1
usb4 at ohci2: USB revision 1.0
uhub4 at usb4 "ATI OHCI root hub" rev 1.00/1.00 addr 1
usb5 at ohci3: USB revision 1.0
uhub5 at usb5 "ATI OHCI root hub" rev 1.00/1.00 addr 1
isa0 at pcib0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pmsi0 at pckbc0 (aux slot)
pckbc0: using irq 12 for aux slot
wsmouse0 at pmsi0 mux 0
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
spkr0 at pcppi0
it0 at isa0 port 0x2e/2: IT8718F rev 5, EC port 0xe80
usb6 at ohci4: USB revision 1.0
uhub6 at usb6 "ATI OHCI root hub" rev 1.00/1.00 addr 1
mtrr: Pentium Pro MTRR support
run0 at uhub0 port 6 "Ralink 802.11 n WLAN" rev 2.00/1.01 addr 2
run0: MAC/BBP RT2860 (rev 0x0103), RF RT2820 (MIMO 2T2R), address 00:22:b0:0d:5d:82
umass0 at uhub2 port 1 configuration 1 interface 0 " USB Reader" rev 1.10/1.00 addr 2
umass0: using SCSI over Bulk-Only
scsibus1 at umass0: 2 targets, initiator 0
sd0 at scsibus1 targ 1 lun 0: <Generic, USB SD Reader, 1.00> SCSI0 0/direct removable
sd0: drive offline
sd1 at scsibus1 targ 1 lun 1: <Generic, USB CF Reader, 1.01> SCSI0 0/direct removable
sd1: drive offline
sd2 at scsibus1 targ 1 lun 2: <Generic, USB SM Reader, 1.02> SCSI0 0/direct removable
sd2: drive offline
sd3 at scsibus1 targ 1 lun 3: <Generic, USB MS Reader, 1.03> SCSI0 0/direct removable
sd3: drive offline
uhidev0 at uhub4 port 2 configuration 1 interface 0 "Plus More Enterprise LTD. USB-compliant keyboard" rev 1.10/1.00 addr 2
uhidev0: iclass 3/1
ukbd0 at uhidev0: 8 modifier keys, 6 key codes
wskbd1 at ukbd0 mux 1
wskbd1: connecting to wsdisplay0
uhidev1 at uhub4 port 2 configuration 1 interface 1 "Plus More Enterprise LTD. USB-compliant keyboard" rev 1.10/1.00 addr 2
uhidev1: iclass 3/1, 3 report ids
uhid0 at uhidev1 reportid 1: input=2, output=0, feature=0
uhid1 at uhidev1 reportid 2: input=1, output=0, feature=0
ums0 at uhidev1 reportid 3: 0 button, Z dir
wsmouse1 at ums0 mux 0
softraid0 at root
root on wd0a swap on wd0b dump on wd0b
Last edited by Carpetsmoker; 28th December 2009 at 03:31 AM. Reason: s/quote/code/
Reply With Quote
  #4   (View Single Post)  
Old 28th December 2009
BSDfan666 BSDfan666 is offline
Real Name: N/A, this is the interweb.
Banned
  
Join Date: Apr 2008
Location: Ontario, Canada
Posts: 2,223
Default
I really don't know a whole lot about wireless configuration, but it may be a good idea to try specifying the channel implicitly.. and you can try unplugging it and trying again if that fails.

$ sudo ifconfig run0 chan ? nwid MYNETWORK nwkey 0xMYKEYTRIPLECHECKED

Also, I notice that pciide(4) fails to establish a DMA mode for devices attached to your SATA controller.. you should check your BIOS and see if you're able to configure the device in AHCI mode, otherwise you'll need to manually patch the ahci(4) driver to attach (..PIO mode is slow, and uses a lot of CPU time).

Code:
pciide0 at pci0 dev 17 function 0 "ATI SBx00 SATA" rev 0x00: DMA (unsupported), channel 0 configured to native-PCI, channel 1 configured to native-PCI
pciide0: using apic 2 int 22 (irq 10) for native-PCI interrupt
wd0 at pciide0 channel 0 drive 0: <WDC WD3200AAJS-22B4A0>
wd0: 16-sector PIO, LBA48, 305245MB, 625142448 sectors
atapiscsi0 at pciide0 channel 1 drive 0
scsibus0 at atapiscsi0: 2 targets
cd0 at scsibus0 targ 0 lun 0: <HL-DT-ST, DVDRAM GH15F, EG00> ATAPI 5/cdrom removable
If you can toggle this in your BIOS, you will need to change your /etc/fstab file to reflect this, it will be an sd(4) device instead of wd(4).

Also, your TV/MPEG capture card is not supported by OpenBSD.

Good luck, please consider editing at least your ifconfig output so that it's easier to distinguish between interfaces.
Reply With Quote
  #5   (View Single Post)  
Old 28th December 2009
RadioKJ RadioKJ is offline
New User
  
Join Date: Dec 2009
Posts: 8
Default
Manually choosing the channel led to no difference. It automatically found the right one anyway.

I don't particularly care about the TV card. I'm just too lazy to remove it from the computer.

Apparently new users can't edit posts. If it's helpful, here's a repost:
Code:
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 33152
	priority: 0
	groups: lo
	inet 127.0.0.1 netmask 0xff000000
	inet6 ::1 prefixlen 128
	inet6 fe80::1%lo0 prefixlen 64 scopeid 0x3
msk0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> mtu 1500
	lladdr 00:1f:e2:3c:5e:e3
	priority: 0
	media: Ethernet autoselect (none)
	status: no carrier
enc0: flags=0<> mtu 1536
	priority: 0
run0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
	lladdr 00:22:b0:0d:5d:82
	priority: 4
	groups: wlan
	media: IEEE802.11 autoselect (DS1 mode 11g)
	status: active
	ieee80211: nwid VERIFIED chan 11 bssid 00:14:bf:9e:8a:7e 46dB nwkey 0xVERIFIED
	inet6 fe80::222:b0ff:fe0d:5d82%run0 prefixlen 64 scopeid 0x4
pflog0: flags=141<UP,RUNNING,PROMISC> mtu 33152
	priority: 0
	groups: pflog
Reply With Quote
  #6   (View Single Post)  
Old 28th December 2009
There0 There0 is offline
./dev/null
  
Join Date: Jul 2008
Posts: 170
Default
Here is the output of my hostname.iwn0 file (yours would be hostname.run0)

dhcp nwid WiFiNet wpa wpapsk $(wpa-psk WiFiNet wifipassword)

This is my currently working config, the WiFiNet is altered and wifipassword is not my password, i do NOT use 0x in front of it for the hostname file, give this a try and feel free to post back.
__________________
The more you learn, the more you realize how little you know ....
Reply With Quote
  #7   (View Single Post)  
Old 28th December 2009
RadioKJ RadioKJ is offline
New User
  
Join Date: Dec 2009
Posts: 8
Default
Unfortunately I'm stuck using WEP on my router due to a couple devices (soon to be replaced) that don't support WPA. At any rate, putting everything into the hostname.run0 file hasn't changed the result.
Reply With Quote
  #8   (View Single Post)  
Old 28th December 2009
BSDfan666 BSDfan666 is offline
Real Name: N/A, this is the interweb.
Banned
  
Join Date: Apr 2008
Location: Ontario, Canada
Posts: 2,223
Default
Can you post the RAMDISK kernel dmesg? while diagnosing issues like this is often futile.. perhaps we'll get lucky.

You could always try installing a snapshot, maybe you're running into something that was fixed after the release.
Reply With Quote
  #9   (View Single Post)  
Old 28th December 2009
There0 There0 is offline
./dev/null
  
Join Date: Jul 2008
Posts: 170
Default
Quote:
Unfortunately I'm stuck using WEP on my router due to a couple devices (soon to be replaced) that don't support WPA. At any rate, putting everything into the hostname.run0 file hasn't changed the result.
Quote:
EXAMPLES
The following hostname.if(5) example configures iwn0 to join whatever
network is available on boot, using WEP key ``0x1deadbeef1'', channel 11,
obtaining an IP address using DHCP:

dhcp NONE NONE NONE nwkey 0x1deadbeef1 chan 11
This is the syntax for WEP (within a hostname file), i sent you syntax concerning WPA-PSK, edit accordingly, i was unaware (lack of details) what you were using WEP not WPA.

Yucky for that, but could you please perhaps post some syntax (and outcome)? or the error messages themselves? "hasn't changed the result" is hard to diagnose from here. I am aware you can not connect and just looking for a bit more detail that may help.

Did you restart networking after you tried using a hostname file? perhaps a reboot to reveal any other types of errors at startup? Also posting the RAMDISK kernel dmesg as BSDFan666 suggest maybe helpful, you did state that it worked from the installer and not after, that is all we know ...

Quote:
while diagnosing issues like this is often futile.. perhaps we'll get lucky.
Futile is correct, the word "lucky" stems (etymologically) from Lucifer, let us use the word fortunate instead? perhaps avoiding the ups and downs and uncertainties of "luck" or "lady luck" hehehe, geez me ...
__________________
The more you learn, the more you realize how little you know ....
Last edited by There0; 28th December 2009 at 06:56 AM.
Reply With Quote
  #10   (View Single Post)  
Old 28th December 2009
RadioKJ RadioKJ is offline
New User
  
Join Date: Dec 2009
Posts: 8
Default
Damnedest thing happened: it now works.

I loaded the ramdisk kernel as suggested and got the dmesg:
Code:
OpenBSD 4.6 (RAMDISK_CD) #51: Thu Jul  9 21:35:49 MDT 2009
    deraadt@amd64.openbsd.org:/usr/src/sys/arch/amd64/compile/RAMDISK_CD
real mem = 1877540864 (1790MB)
avail mem = 1811050496 (1727MB)
mainbus0 at root
bios0 at mainbus0: SMBIOS rev. 2.5 @ 0x9f400 (30 entries)
bios0: vendor American Megatrends Inc. version "R03-B0" date 05/07/2008
bios0: Acer Aspire M1201
acpi0 at bios0: rev 0
acpi0: tables DSDT FACP APIC MCFG SLIC OEMB HPET ASF! AWMI SSDT
acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat
cpu0 at mainbus0: apid 0 (boot processor)
cpu0: AMD Athlon(tm) 64 X2 Dual Core Processor 4400+, 2299.44 MHz
cpu0: FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,MMX,FXSR,SSE,SSE2,HTT,SSE3,CX16,NXE,MMXX,FFXSR,LONG,3DNOW2,3DNOW
cpu0: 64KB 64b/line 2-way I-cache, 64KB 64b/line 2-way D-cache, 512KB 64b/line 16-way L2 cache
cpu0: ITLB 32 4KB entries fully associative, 8 4MB entries fully associative
cpu0: DTLB 32 4KB entries fully associative, 8 4MB entries fully associative
cpu0: apic clock running at 199MHz
cpu at mainbus0: not configured
ioapic0 at mainbus0 apid 2 pa 0xfec00000, version 21, 24 pins
ioapic0: misconfigured as apic 0, remapped to apid 2
acpiprt0 at acpi0: bus 0 (PCI0)
acpiprt1 at acpi0: bus 1 (P0P1)
acpiprt2 at acpi0: bus -1 (PCE2)
acpiprt3 at acpi0: bus -1 (PCE3)
acpiprt4 at acpi0: bus 2 (PCE4)
acpiprt5 at acpi0: bus 3 (PCE5)
acpiprt6 at acpi0: bus 4 (PCE6)
acpiprt7 at acpi0: bus -1 (PCE7)
acpiprt8 at acpi0: bus 5 (P0PC)
pci0 at mainbus0 bus 0
pchb0 at pci0 dev 0 function 0 "ATI RS740 Host" rev 0x00
ppb0 at pci0 dev 1 function 0 "ATI RS690 PCIE" rev 0x00
pci1 at ppb0 bus 1
vga1 at pci1 dev 5 function 0 "ATI Radeon 2100" rev 0x00
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
ppb1 at pci0 dev 4 function 0 vendor "ATI", unknown product 0x7914 rev 0x00
pci2 at ppb1 bus 2
vendor "Conexant", unknown product 0x8880 (class multimedia subclass video, rev 0x0f) at pci2 dev 0 function 0 not configured
ppb2 at pci0 dev 5 function 0 "ATI RS690 PCIE" rev 0x00
pci3 at ppb2 bus 3
mskc0 at pci3 dev 0 function 0 "Marvell Yukon 88E8071" rev 0x16, Yukon-2 Extreme rev. B0 (0x2): apic 2 int 17 (irq 11)
msk0 at mskc0 port A: address 00:1f:e2:3c:5e:e3
eephy0 at msk0 phy 0: 88E1149 Gigabit PHY, rev. 1
ppb3 at pci0 dev 6 function 0 "ATI RS690 PCIE" rev 0x00
pci4 at ppb3 bus 4
"JMicron FireWire" rev 0x00 at pci4 dev 0 function 0 not configured
pciide0 at pci0 dev 17 function 0 "ATI SBx00 SATA" rev 0x00: DMA (unsupported), channel 0 configured to native-PCI, channel 1 configured to native-PCI
pciide0: using apic 2 int 22 (irq 10) for native-PCI interrupt
wd0 at pciide0 channel 0 drive 0: <WDC WD3200AAJS-22B4A0>
wd0: 16-sector PIO, LBA48, 305245MB, 625142448 sectors
atapiscsi0 at pciide0 channel 1 drive 0
scsibus0 at atapiscsi0: 2 targets
cd0 at scsibus0 targ 0 lun 0: <HL-DT-ST, DVDRAM GH15F, EG00> ATAPI 5/cdrom removable
ohci0 at pci0 dev 18 function 0 "ATI SB700 USB" rev 0x00: apic 2 int 16 (irq 11), version 1.0, legacy support
ohci1 at pci0 dev 18 function 1 "ATI SB700 USB" rev 0x00: apic 2 int 16 (irq 11), version 1.0, legacy support
ehci0 at pci0 dev 18 function 2 "ATI SB700 USB2" rev 0x00: apic 2 int 17 (irq 11)
usb0 at ehci0: USB revision 2.0
uhub0 at usb0 "ATI EHCI root hub" rev 2.00/1.00 addr 1
ohci2 at pci0 dev 19 function 0 "ATI SB700 USB" rev 0x00: apic 2 int 18 (irq 10), version 1.0, legacy support
ohci3 at pci0 dev 19 function 1 "ATI SB700 USB" rev 0x00: apic 2 int 18 (irq 10), version 1.0, legacy support
ehci1 at pci0 dev 19 function 2 "ATI SB700 USB2" rev 0x00: apic 2 int 19 (irq 10)
usb1 at ehci1: USB revision 2.0
uhub1 at usb1 "ATI EHCI root hub" rev 2.00/1.00 addr 1
"ATI SBx00 SMBus" rev 0x3a at pci0 dev 20 function 0 not configured
pciide1 at pci0 dev 20 function 1 "ATI SB700 IDE" rev 0x00: DMA, channel 0 configured to compatibility, channel 1 configured to compatibility
"ATI SBx00 HD Audio" rev 0x00 at pci0 dev 20 function 2 not configured
"ATI SB700 ISA" rev 0x00 at pci0 dev 20 function 3 not configured
ppb4 at pci0 dev 20 function 4 "ATI SB600 PCI" rev 0x00
pci5 at ppb4 bus 5
ohci4 at pci0 dev 20 function 5 "ATI SB700 USB" rev 0x00: apic 2 int 18 (irq 10), version 1.0, legacy support
pchb1 at pci0 dev 24 function 0 "AMD AMD64 0Fh HyperTransport" rev 0x00
pchb2 at pci0 dev 24 function 1 "AMD AMD64 0Fh Address Map" rev 0x00
pchb3 at pci0 dev 24 function 2 "AMD AMD64 0Fh DRAM Cfg" rev 0x00
pchb4 at pci0 dev 24 function 3 "AMD AMD64 0Fh Misc Cfg" rev 0x00
usb2 at ohci0: USB revision 1.0
uhub2 at usb2 "ATI OHCI root hub" rev 1.00/1.00 addr 1
usb3 at ohci1: USB revision 1.0
uhub3 at usb3 "ATI OHCI root hub" rev 1.00/1.00 addr 1
usb4 at ohci2: USB revision 1.0
uhub4 at usb4 "ATI OHCI root hub" rev 1.00/1.00 addr 1
usb5 at ohci3: USB revision 1.0
uhub5 at usb5 "ATI OHCI root hub" rev 1.00/1.00 addr 1
usb6 at ohci4: USB revision 1.0
uhub6 at usb6 "ATI OHCI root hub" rev 1.00/1.00 addr 1
isa0 at mainbus0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
rd0: fixed, 4480 blocks
run0 at uhub0 port 6 "Ralink 802.11 n WLAN" rev 2.00/1.01 addr 2
run0: MAC/BBP RT2860 (rev 0x0103), RF RT2820 (MIMO 2T2R), address 00:22:b0:0d:5d:82
umass0 at uhub2 port 1 configuration 1 interface 0 " USB Reader" rev 1.10/1.00 addr 2
umass0: using SCSI over Bulk-Only
scsibus1 at umass0: 2 targets, initiator 0
sd0 at scsibus1 targ 1 lun 0: <Generic, USB SD Reader, 1.00> SCSI0 0/direct removable
sd0: drive offline
sd1 at scsibus1 targ 1 lun 1: <Generic, USB CF Reader, 1.01> SCSI0 0/direct removable
sd1: drive offline
sd2 at scsibus1 targ 1 lun 2: <Generic, USB SM Reader, 1.02> SCSI0 0/direct removable
sd2: drive offline
sd3 at scsibus1 targ 1 lun 3: <Generic, USB MS Reader, 1.03> SCSI0 0/direct removable
sd3: drive offline
uhidev0 at uhub4 port 2 configuration 1 interface 0 "Plus More Enterprise LTD. USB-compliant keyboard" rev 1.10/1.00 addr 2
uhidev0: iclass 3/1
ukbd0 at uhidev0
wskbd1 at ukbd0 mux 1
wskbd1: connecting to wsdisplay0
uhidev1 at uhub4 port 2 configuration 1 interface 1 "Plus More Enterprise LTD. USB-compliant keyboard" rev 1.10/1.00 addr 2
uhidev1: iclass 3/1, 3 report ids
uhid at uhidev1 reportid 1 not configured
uhid at uhidev1 reportid 2 not configured
uhid at uhidev1 reportid 3 not configured
softraid0 at root
root on rd0a swap on rd0b dump on rd0b
While I was there I tried setting up the network just as I've been doing and it connected fine; the same as it did during install. Then when I rebooted normally it again connected properly (automatically thanks to hostname.run0). Before this I would continue to get the messages from my first post. It's now connecting perfectly after repeated reboots.

In case it helps figure out what happened, here's the new dmesg after rebooting with wifi working:
Code:
ature=0
ums0 at uhidev1 reportid 3: 0 button, Z dir
wsmouse1 at ums0 mux 0
softraid0 at root
root on wd0a swap on wd0b dump on wd0b
syncing disks... 
OpenBSD 4.6 (GENERIC.MP) #81: Thu Jul  9 21:26:19 MDT 2009
    deraadt@amd64.openbsd.org:/usr/src/sys/arch/amd64/compile/GENERIC.MP
real mem = 1877540864 (1790MB)
avail mem = 1809547264 (1725MB)
mainbus0 at root
bios0 at mainbus0: SMBIOS rev. 2.5 @ 0x9f400 (30 entries)
bios0: vendor American Megatrends Inc. version "R03-B0" date 05/07/2008
bios0: Acer Aspire M1201
acpi0 at bios0: rev 0
acpi0: tables DSDT FACP APIC MCFG SLIC OEMB HPET ASF! AWMI SSDT
acpi0: wakeup devices PCE2(S4) PCE3(S4) PCE4(S4) PCE5(S4) PCE6(S4) PCE7(S4) SBAZ(S4) UAR1(S3) UAR2(S3) PS2K(S3) PS2M(S3) P0PC(S4) UHC1(S3) UHC2(S3) UHC3(S3) USB4(S3) UHC5(S3) UHC6(S3) UHC7(S3) PWRB(S3)
acpitimer0 at acpi0: 3579545 Hz, 32 bits
acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat
cpu0 at mainbus0: apid 0 (boot processor)
cpu0: AMD Athlon(tm) 64 X2 Dual Core Processor 4400+, 2299.41 MHz
cpu0: FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,MMX,FXSR,SSE,SSE2,HTT,SSE3,CX16,NXE,MMXX,FFXSR,LONG,3DNOW2,3DNOW
cpu0: 64KB 64b/line 2-way I-cache, 64KB 64b/line 2-way D-cache, 512KB 64b/line 16-way L2 cache
cpu0: ITLB 32 4KB entries fully associative, 8 4MB entries fully associative
cpu0: DTLB 32 4KB entries fully associative, 8 4MB entries fully associative
cpu0: apic clock running at 199MHz
cpu1 at mainbus0: apid 1 (application processor)
cpu1: AMD Athlon(tm) 64 X2 Dual Core Processor 4400+, 2299.12 MHz
cpu1: FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,MMX,FXSR,SSE,SSE2,HTT,SSE3,CX16,NXE,MMXX,FFXSR,LONG,3DNOW2,3DNOW
cpu1: 64KB 64b/line 2-way I-cache, 64KB 64b/line 2-way D-cache, 512KB 64b/line 16-way L2 cache
cpu1: ITLB 32 4KB entries fully associative, 8 4MB entries fully associative
cpu1: DTLB 32 4KB entries fully associative, 8 4MB entries fully associative
ioapic0 at mainbus0 apid 2 pa 0xfec00000, version 21, 24 pins
ioapic0: misconfigured as apic 0, remapped to apid 2
acpihpet0 at acpi0: 14318180 Hz
acpiprt0 at acpi0: bus 0 (PCI0)
acpiprt1 at acpi0: bus 1 (P0P1)
acpiprt2 at acpi0: bus -1 (PCE2)
acpiprt3 at acpi0: bus -1 (PCE3)
acpiprt4 at acpi0: bus 2 (PCE4)
acpiprt5 at acpi0: bus 3 (PCE5)
acpiprt6 at acpi0: bus 4 (PCE6)
acpiprt7 at acpi0: bus -1 (PCE7)
acpiprt8 at acpi0: bus 5 (P0PC)
acpicpu0 at acpi0: PSS
acpicpu1 at acpi0: PSS
acpitz0 at acpi0: critical temperature 90 degC
acpibtn0 at acpi0: PWRB
cpu0: PowerNow! K8 2299 MHz: speeds: 2300 2200 2000 1800 1000 MHz
pci0 at mainbus0 bus 0
pchb0 at pci0 dev 0 function 0 "ATI RS740 Host" rev 0x00
ppb0 at pci0 dev 1 function 0 "ATI RS690 PCIE" rev 0x00
pci1 at ppb0 bus 1
vga1 at pci1 dev 5 function 0 "ATI Radeon 2100" rev 0x00
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
ppb1 at pci0 dev 4 function 0 vendor "ATI", unknown product 0x7914 rev 0x00
pci2 at ppb1 bus 2
vendor "Conexant", unknown product 0x8880 (class multimedia subclass video, rev 0x0f) at pci2 dev 0 function 0 not configured
ppb2 at pci0 dev 5 function 0 "ATI RS690 PCIE" rev 0x00
pci3 at ppb2 bus 3
mskc0 at pci3 dev 0 function 0 "Marvell Yukon 88E8071" rev 0x16, Yukon-2 Extreme rev. B0 (0x2): apic 2 int 17 (irq 11)
msk0 at mskc0 port A: address 00:1f:e2:3c:5e:e3
eephy0 at msk0 phy 0: 88E1149 Gigabit PHY, rev. 1
ppb3 at pci0 dev 6 function 0 "ATI RS690 PCIE" rev 0x00
pci4 at ppb3 bus 4
"JMicron FireWire" rev 0x00 at pci4 dev 0 function 0 not configured
pciide0 at pci0 dev 17 function 0 "ATI SBx00 SATA" rev 0x00: DMA (unsupported), channel 0 configured to native-PCI, channel 1 configured to native-PCI
pciide0: using apic 2 int 22 (irq 10) for native-PCI interrupt
wd0 at pciide0 channel 0 drive 0: <WDC WD3200AAJS-22B4A0>
wd0: 16-sector PIO, LBA48, 305245MB, 625142448 sectors
atapiscsi0 at pciide0 channel 1 drive 0
scsibus0 at atapiscsi0: 2 targets
cd0 at scsibus0 targ 0 lun 0: <HL-DT-ST, DVDRAM GH15F, EG00> ATAPI 5/cdrom removable
ohci0 at pci0 dev 18 function 0 "ATI SB700 USB" rev 0x00: apic 2 int 16 (irq 11), version 1.0, legacy support
ohci1 at pci0 dev 18 function 1 "ATI SB700 USB" rev 0x00: apic 2 int 16 (irq 11), version 1.0, legacy support
ehci0 at pci0 dev 18 function 2 "ATI SB700 USB2" rev 0x00: apic 2 int 17 (irq 11)
usb0 at ehci0: USB revision 2.0
uhub0 at usb0 "ATI EHCI root hub" rev 2.00/1.00 addr 1
ohci2 at pci0 dev 19 function 0 "ATI SB700 USB" rev 0x00: apic 2 int 18 (irq 10), version 1.0, legacy support
ohci3 at pci0 dev 19 function 1 "ATI SB700 USB" rev 0x00: apic 2 int 18 (irq 10), version 1.0, legacy support
ehci1 at pci0 dev 19 function 2 "ATI SB700 USB2" rev 0x00: apic 2 int 19 (irq 10)
usb1 at ehci1: USB revision 2.0
uhub1 at usb1 "ATI EHCI root hub" rev 2.00/1.00 addr 1
piixpm0 at pci0 dev 20 function 0 "ATI SBx00 SMBus" rev 0x3a: SMI
iic0 at piixpm0
spdmem0 at iic0 addr 0x50: 1GB DDR2 SDRAM non-parity PC2-5300CL5
spdmem1 at iic0 addr 0x51: 1GB DDR2 SDRAM non-parity PC2-5300CL5
pciide1 at pci0 dev 20 function 1 "ATI SB700 IDE" rev 0x00: DMA, channel 0 configured to compatibility, channel 1 configured to compatibility
azalia0 at pci0 dev 20 function 2 "ATI SBx00 HD Audio" rev 0x00: apic 2 int 16 (irq 11)
azalia0: codecs: Realtek ALC888
audio0 at azalia0
pcib0 at pci0 dev 20 function 3 "ATI SB700 ISA" rev 0x00
ppb4 at pci0 dev 20 function 4 "ATI SB600 PCI" rev 0x00
pci5 at ppb4 bus 5
ohci4 at pci0 dev 20 function 5 "ATI SB700 USB" rev 0x00: apic 2 int 18 (irq 10), version 1.0, legacy support
pchb1 at pci0 dev 24 function 0 "AMD AMD64 0Fh HyperTransport" rev 0x00
pchb2 at pci0 dev 24 function 1 "AMD AMD64 0Fh Address Map" rev 0x00
pchb3 at pci0 dev 24 function 2 "AMD AMD64 0Fh DRAM Cfg" rev 0x00
kate0 at pci0 dev 24 function 3 "AMD AMD64 0Fh Misc Cfg" rev 0x00: core rev BH-G2
usb2 at ohci0: USB revision 1.0
uhub2 at usb2 "ATI OHCI root hub" rev 1.00/1.00 addr 1
usb3 at ohci1: USB revision 1.0
uhub3 at usb3 "ATI OHCI root hub" rev 1.00/1.00 addr 1
usb4 at ohci2: USB revision 1.0
uhub4 at usb4 "ATI OHCI root hub" rev 1.00/1.00 addr 1
usb5 at ohci3: USB revision 1.0
uhub5 at usb5 "ATI OHCI root hub" rev 1.00/1.00 addr 1
isa0 at pcib0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pmsi0 at pckbc0 (aux slot)
pckbc0: using irq 12 for aux slot
wsmouse0 at pmsi0 mux 0
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
spkr0 at pcppi0
it0 at isa0 port 0x2e/2: IT8718F rev 5, EC port 0xe80
usb6 at ohci4: USB revision 1.0
uhub6 at usb6 "ATI OHCI root hub" rev 1.00/1.00 addr 1
mtrr: Pentium Pro MTRR support
run0 at uhub0 port 6 "Ralink 802.11 n WLAN" rev 2.00/1.01 addr 2
run0: MAC/BBP RT2860 (rev 0x0103), RF RT2820 (MIMO 2T2R), address 00:22:b0:0d:5d:82
umass0 at uhub2 port 1 configuration 1 interface 0 " USB Reader" rev 1.10/1.00 addr 2
umass0: using SCSI over Bulk-Only
scsibus1 at umass0: 2 targets, initiator 0
sd0 at scsibus1 targ 1 lun 0: <Generic, USB SD Reader, 1.00> SCSI0 0/direct removable
sd0: 240MB, 512 bytes/sec, 492288 sec total
sd1 at scsibus1 targ 1 lun 1: <Generic, USB CF Reader, 1.01> SCSI0 0/direct removable
sd1: drive offline
sd2 at scsibus1 targ 1 lun 2: <Generic, USB SM Reader, 1.02> SCSI0 0/direct removable
sd2: drive offline
sd3 at scsibus1 targ 1 lun 3: <Generic, USB MS Reader, 1.03> SCSI0 0/direct removable
sd3: drive offline
uhidev0 at uhub4 port 2 configuration 1 interface 0 "Plus More Enterprise LTD. USB-compliant keyboard" rev 1.10/1.00 addr 2
uhidev0: iclass 3/1
ukbd0 at uhidev0: 8 modifier keys, 6 key codes
wskbd1 at ukbd0 mux 1
wskbd1: connecting to wsdisplay0
uhidev1 at uhub4 port 2 configuration 1 interface 1 "Plus More Enterprise LTD. USB-compliant keyboard" rev 1.10/1.00 addr 2
uhidev1: iclass 3/1, 3 report ids
uhid0 at uhidev1 reportid 1: input=2, output=0, feature=0
uhid1 at uhidev1 reportid 2: input=1, output=0, feature=0
ums0 at uhidev1 reportid 3: 0 button, Z dir
wsmouse1 at ums0 mux 0
softraid0 at root
root on wd0a swap on wd0b dump on wd0b
usb_insert_transfer: xfer=0xffff800000352800 not busy 0x4f4e5155
usb_insert_transfer: xfer=0xffff800000352800 not busy 0x4f4e5155
usb_insert_transfer: xfer=0xffff800000352800 not busy 0x4f4e5155
usb_insert_transfer: xfer=0xffff800000373600 not busy 0x4f4e5155
usb_insert_transfer: xfer=0xffff80000036c600 not busy 0x4f4e5155
syncing disks... 
OpenBSD 4.6 (GENERIC.MP) #81: Thu Jul  9 21:26:19 MDT 2009
    deraadt@amd64.openbsd.org:/usr/src/sys/arch/amd64/compile/GENERIC.MP
real mem = 1877540864 (1790MB)
avail mem = 1809547264 (1725MB)
mainbus0 at root
bios0 at mainbus0: SMBIOS rev. 2.5 @ 0x9f400 (30 entries)
bios0: vendor American Megatrends Inc. version "R03-B0" date 05/07/2008
bios0: Acer Aspire M1201
acpi0 at bios0: rev 0
acpi0: tables DSDT FACP APIC MCFG SLIC OEMB HPET ASF! AWMI SSDT
acpi0: wakeup devices PCE2(S4) PCE3(S4) PCE4(S4) PCE5(S4) PCE6(S4) PCE7(S4) SBAZ(S4) UAR1(S3) UAR2(S3) PS2K(S3) PS2M(S3) P0PC(S4) UHC1(S3) UHC2(S3) UHC3(S3) USB4(S3) UHC5(S3) UHC6(S3) UHC7(S3) PWRB(S3)
acpitimer0 at acpi0: 3579545 Hz, 32 bits
acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat
cpu0 at mainbus0: apid 0 (boot processor)
cpu0: AMD Athlon(tm) 64 X2 Dual Core Processor 4400+, 2299.42 MHz
cpu0: FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,MMX,FXSR,SSE,SSE2,HTT,SSE3,CX16,NXE,MMXX,FFXSR,LONG,3DNOW2,3DNOW
cpu0: 64KB 64b/line 2-way I-cache, 64KB 64b/line 2-way D-cache, 512KB 64b/line 16-way L2 cache
cpu0: ITLB 32 4KB entries fully associative, 8 4MB entries fully associative
cpu0: DTLB 32 4KB entries fully associative, 8 4MB entries fully associative
cpu0: apic clock running at 199MHz
cpu1 at mainbus0: apid 1 (application processor)
cpu1: AMD Athlon(tm) 64 X2 Dual Core Processor 4400+, 2299.12 MHz
cpu1: FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,MMX,FXSR,SSE,SSE2,HTT,SSE3,CX16,NXE,MMXX,FFXSR,LONG,3DNOW2,3DNOW
cpu1: 64KB 64b/line 2-way I-cache, 64KB 64b/line 2-way D-cache, 512KB 64b/line 16-way L2 cache
cpu1: ITLB 32 4KB entries fully associative, 8 4MB entries fully associative
cpu1: DTLB 32 4KB entries fully associative, 8 4MB entries fully associative
ioapic0 at mainbus0 apid 2 pa 0xfec00000, version 21, 24 pins
ioapic0: misconfigured as apic 0, remapped to apid 2
acpihpet0 at acpi0: 14318180 Hz
acpiprt0 at acpi0: bus 0 (PCI0)
acpiprt1 at acpi0: bus 1 (P0P1)
acpiprt2 at acpi0: bus -1 (PCE2)
acpiprt3 at acpi0: bus -1 (PCE3)
acpiprt4 at acpi0: bus 2 (PCE4)
acpiprt5 at acpi0: bus 3 (PCE5)
acpiprt6 at acpi0: bus 4 (PCE6)
acpiprt7 at acpi0: bus -1 (PCE7)
acpiprt8 at acpi0: bus 5 (P0PC)
acpicpu0 at acpi0: PSS
acpicpu1 at acpi0: PSS
acpitz0 at acpi0: critical temperature 90 degC
acpibtn0 at acpi0: PWRB
cpu0: PowerNow! K8 2299 MHz: speeds: 2300 2200 2000 1800 1000 MHz
pci0 at mainbus0 bus 0
pchb0 at pci0 dev 0 function 0 "ATI RS740 Host" rev 0x00
ppb0 at pci0 dev 1 function 0 "ATI RS690 PCIE" rev 0x00
pci1 at ppb0 bus 1
vga1 at pci1 dev 5 function 0 "ATI Radeon 2100" rev 0x00
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
ppb1 at pci0 dev 4 function 0 vendor "ATI", unknown product 0x7914 rev 0x00
pci2 at ppb1 bus 2
vendor "Conexant", unknown product 0x8880 (class multimedia subclass video, rev 0x0f) at pci2 dev 0 function 0 not configured
ppb2 at pci0 dev 5 function 0 "ATI RS690 PCIE" rev 0x00
pci3 at ppb2 bus 3
mskc0 at pci3 dev 0 function 0 "Marvell Yukon 88E8071" rev 0x16, Yukon-2 Extreme rev. B0 (0x2): apic 2 int 17 (irq 11)
msk0 at mskc0 port A: address 00:1f:e2:3c:5e:e3
eephy0 at msk0 phy 0: 88E1149 Gigabit PHY, rev. 1
ppb3 at pci0 dev 6 function 0 "ATI RS690 PCIE" rev 0x00
pci4 at ppb3 bus 4
"JMicron FireWire" rev 0x00 at pci4 dev 0 function 0 not configured
pciide0 at pci0 dev 17 function 0 "ATI SBx00 SATA" rev 0x00: DMA (unsupported), channel 0 configured to native-PCI, channel 1 configured to native-PCI
pciide0: using apic 2 int 22 (irq 10) for native-PCI interrupt
wd0 at pciide0 channel 0 drive 0: <WDC WD3200AAJS-22B4A0>
wd0: 16-sector PIO, LBA48, 305245MB, 625142448 sectors
atapiscsi0 at pciide0 channel 1 drive 0
scsibus0 at atapiscsi0: 2 targets
cd0 at scsibus0 targ 0 lun 0: <HL-DT-ST, DVDRAM GH15F, EG00> ATAPI 5/cdrom removable
ohci0 at pci0 dev 18 function 0 "ATI SB700 USB" rev 0x00: apic 2 int 16 (irq 11), version 1.0, legacy support
ohci1 at pci0 dev 18 function 1 "ATI SB700 USB" rev 0x00: apic 2 int 16 (irq 11), version 1.0, legacy support
ehci0 at pci0 dev 18 function 2 "ATI SB700 USB2" rev 0x00: apic 2 int 17 (irq 11)
usb0 at ehci0: USB revision 2.0
uhub0 at usb0 "ATI EHCI root hub" rev 2.00/1.00 addr 1
ohci2 at pci0 dev 19 function 0 "ATI SB700 USB" rev 0x00: apic 2 int 18 (irq 10), version 1.0, legacy support
ohci3 at pci0 dev 19 function 1 "ATI SB700 USB" rev 0x00: apic 2 int 18 (irq 10), version 1.0, legacy support
ehci1 at pci0 dev 19 function 2 "ATI SB700 USB2" rev 0x00: apic 2 int 19 (irq 10)
usb1 at ehci1: USB revision 2.0
uhub1 at usb1 "ATI EHCI root hub" rev 2.00/1.00 addr 1
piixpm0 at pci0 dev 20 function 0 "ATI SBx00 SMBus" rev 0x3a: SMI
iic0 at piixpm0
spdmem0 at iic0 addr 0x50: 1GB DDR2 SDRAM non-parity PC2-5300CL5
spdmem1 at iic0 addr 0x51: 1GB DDR2 SDRAM non-parity PC2-5300CL5
pciide1 at pci0 dev 20 function 1 "ATI SB700 IDE" rev 0x00: DMA, channel 0 configured to compatibility, channel 1 configured to compatibility
azalia0 at pci0 dev 20 function 2 "ATI SBx00 HD Audio" rev 0x00: apic 2 int 16 (irq 11)
azalia0: codecs: Realtek ALC888
audio0 at azalia0
pcib0 at pci0 dev 20 function 3 "ATI SB700 ISA" rev 0x00
ppb4 at pci0 dev 20 function 4 "ATI SB600 PCI" rev 0x00
pci5 at ppb4 bus 5
ohci4 at pci0 dev 20 function 5 "ATI SB700 USB" rev 0x00: apic 2 int 18 (irq 10), version 1.0, legacy support
pchb1 at pci0 dev 24 function 0 "AMD AMD64 0Fh HyperTransport" rev 0x00
pchb2 at pci0 dev 24 function 1 "AMD AMD64 0Fh Address Map" rev 0x00
pchb3 at pci0 dev 24 function 2 "AMD AMD64 0Fh DRAM Cfg" rev 0x00
kate0 at pci0 dev 24 function 3 "AMD AMD64 0Fh Misc Cfg" rev 0x00: core rev BH-G2
usb2 at ohci0: USB revision 1.0
uhub2 at usb2 "ATI OHCI root hub" rev 1.00/1.00 addr 1
usb3 at ohci1: USB revision 1.0
uhub3 at usb3 "ATI OHCI root hub" rev 1.00/1.00 addr 1
usb4 at ohci2: USB revision 1.0
uhub4 at usb4 "ATI OHCI root hub" rev 1.00/1.00 addr 1
usb5 at ohci3: USB revision 1.0
uhub5 at usb5 "ATI OHCI root hub" rev 1.00/1.00 addr 1
isa0 at pcib0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pmsi0 at pckbc0 (aux slot)
pckbc0: using irq 12 for aux slot
wsmouse0 at pmsi0 mux 0
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
spkr0 at pcppi0
it0 at isa0 port 0x2e/2: IT8718F rev 5, EC port 0xe80
usb6 at ohci4: USB revision 1.0
uhub6 at usb6 "ATI OHCI root hub" rev 1.00/1.00 addr 1
mtrr: Pentium Pro MTRR support
run0 at uhub0 port 6 "Ralink 802.11 n WLAN" rev 2.00/1.01 addr 2
run0: MAC/BBP RT2860 (rev 0x0103), RF RT2820 (MIMO 2T2R), address 00:22:b0:0d:5d:82
umass0 at uhub2 port 1 configuration 1 interface 0 " USB Reader" rev 1.10/1.00 addr 2
umass0: using SCSI over Bulk-Only
scsibus1 at umass0: 2 targets, initiator 0
sd0 at scsibus1 targ 1 lun 0: <Generic, USB SD Reader, 1.00> SCSI0 0/direct removable
sd0: drive offline
sd1 at scsibus1 targ 1 lun 1: <Generic, USB CF Reader, 1.01> SCSI0 0/direct removable
sd1: drive offline
sd2 at scsibus1 targ 1 lun 2: <Generic, USB SM Reader, 1.02> SCSI0 0/direct removable
sd2: drive offline
sd3 at scsibus1 targ 1 lun 3: <Generic, USB MS Reader, 1.03> SCSI0 0/direct removable
sd3: drive offline
uhidev0 at uhub4 port 2 configuration 1 interface 0 "Plus More Enterprise LTD. USB-compliant keyboard" rev 1.10/1.00 addr 2
uhidev0: iclass 3/1
ukbd0 at uhidev0: 8 modifier keys, 6 key codes
wskbd1 at ukbd0 mux 1
wskbd1: connecting to wsdisplay0
uhidev1 at uhub4 port 2 configuration 1 interface 1 "Plus More Enterprise LTD. USB-compliant keyboard" rev 1.10/1.00 addr 2
uhidev1: iclass 3/1, 3 report ids
uhid0 at uhidev1 reportid 1: input=2, output=0, feature=0
uhid1 at uhidev1 reportid 2: input=1, output=0, feature=0
ums0 at uhidev1 reportid 3: 0 button, Z dir
wsmouse1 at ums0 mux 0
softraid0 at root
root on wd0a swap on wd0b dump on wd0b
Reply With Quote
  #11   (View Single Post)  
Old 28th December 2009
BSDfan666 BSDfan666 is offline
Real Name: N/A, this is the interweb.
Banned
  
Join Date: Apr 2008
Location: Ontario, Canada
Posts: 2,223
Default
Quote:
Originally Posted by There0 View Post
Futile is correct, the word "lucky" stems (etymologically) from Lucifer, let us use the word fortunate instead?
Fortunately I'm not religious, I use whatever is in the dictionary.. regardless of origin.
Reply With Quote
  #12   (View Single Post)  
Old 28th December 2009
BSDfan666 BSDfan666 is offline
Real Name: N/A, this is the interweb.
Banned
  
Join Date: Apr 2008
Location: Ontario, Canada
Posts: 2,223
Default
The fact that your device sporadically started working after booting the RAMDISK image seems to point out some sort of random initialization problem.. could even be some sort of quirk with your USB controller.

Now that you have that sorted, perhaps you can look into the other issues I pointed out regarding your SATA controller.
Reply With Quote
  #13   (View Single Post)  
Old 28th December 2009
RadioKJ RadioKJ is offline
New User
  
Join Date: Dec 2009
Posts: 8
Default
Thanks. That'll be another time though. Thus far it hasn't caused any problems and I should've been asleep a long time ago for work tomorrow.
Reply With Quote
  #14   (View Single Post)  
Old 28th December 2009
There0 There0 is offline
./dev/null
  
Join Date: Jul 2008
Posts: 170
Default
Quote:
Fortunately I'm not religious, I use whatever is in the dictionary.. regardless of origin.
Hehehehe, for the record i am not very "religous" either, i believe in myself before anything else, i like how you started the sentance with "Fortunately".

Glad to see that a mystery reboot (or boot up from RAMDISK kernel) cured? your WiFi griefs, sleep is a good thing yes almost time for me too.

Quote:
Now that you have that sorted, perhaps you can look into the other issues I pointed out regarding your SATA controller.
GOOD thing to look into, it will increase your disk performance noticably, do not forget to edit your /etc/fstab file to reflect, enjoy
__________________
The more you learn, the more you realize how little you know ....
Reply With Quote
  #15   (View Single Post)  
Old 28th December 2009
RadioKJ RadioKJ is offline
New User
  
Join Date: Dec 2009
Posts: 8
Default
Guess what's broken this morning?

Code:
$ sudo dhclient run0
DHCPREQUEST on run0 to 255.255.255.255 port 67
DHCPREQUEST on run0 to 255.255.255.255 port 67
DHCPDISCOVER on run0 to 255.255.255.255 port 67 interval 3
DHCPDISCOVER on run0 to 255.255.255.255 port 67 interval 7
DHCPDISCOVER on run0 to 255.255.255.255 port 67 interval 15
DHCPDISCOVER on run0 to 255.255.255.255 port 67 interval 11
DHCPDISCOVER on run0 to 255.255.255.255 port 67 interval 15
DHCPDISCOVER on run0 to 255.255.255.255 port 67 interval 10
No DHCPOFFERS received.
Trying recorded lease 192.168.1.109
No working leases in persistent database - sleeping.
I assumed maybe it would only work if the router had already given it the lease, but now it won't even work when I boot to ramdisk. I get the same messages (sans "trying recorded lease"). Trying a second time while in ramdisk gives me the message "Can't find free bpf: No such file or directory".

The same device has no problems under Windows or Linux (ndiswrapper). Perhaps I should replace my router. I intended to do so anyway, but not for a few months. This one doesn't support manually assigning an IP to a MAC address or I'd try that.
Reply With Quote
  #16   (View Single Post)  
Old 28th December 2009
There0 There0 is offline
./dev/null
  
Join Date: Jul 2008
Posts: 170
Default
Perhaps it maybe better to use sh /etc/netstart, i have noticed that dhclient does this to me as well sometimes, ensure your hostname.xxx file is correct (for WEP that is) and restart your networking with the netstart command, sh /etc/netstart run0 ( i prefer sh /etc/netstart because sometime a route or some DNS may poop without a full network restart).

You did state that you did once again boot from RAMDISK kernel and it did not work this morning? i have had to recreate the whole hostname file sometimes because of a space? or some wierd character that DID NOT WORK, that said it almost sounds like your having hardware problems.

If you get a chance hook up to somebody else's router (a friend not a random) and see if you get the same results.
__________________
The more you learn, the more you realize how little you know ....
Reply With Quote
  #17   (View Single Post)  
Old 29th December 2009
shep shep is offline
Real Name: Scott
Regex Recruiter
  
Join Date: May 2008
Location: Dry and Dusty
Posts: 1,557
Default
I have noticed similiar behavior with my RAlink USB (rum driver) device on 4.6 i386. If I plugin the device after power up and then run dhclient from the command line I will not get a lease.

I get a lease 80-90% of the time if I power up with the usb device plugged in.
Last edited by shep; 29th December 2009 at 01:09 AM. Reason: I'm using the rum driver
Reply With Quote
  #18   (View Single Post)  
Old 31st December 2009
RadioKJ RadioKJ is offline
New User
  
Join Date: Dec 2009
Posts: 8
Default
Well thanks anyway for trying everyone, but I've decided to just put this thing back into the closet. A wired network is too inconvenient at the moment and I'm really only using this thing to learn about BSD. I may have another go at it with an old laptop I dug up.
Reply With Quote
  #19   (View Single Post)  
Old 1st January 2010
shep shep is offline
Real Name: Scott
Regex Recruiter
  
Join Date: May 2008
Location: Dry and Dusty
Posts: 1,557
Default
Quote:
Well thanks anyway for trying everyone, but I've decided to just put this thing back into the closet. A wired network is too inconvenient at the moment and I'm really only using this thing to learn about BSD. I may have another go at it with an old laptop I dug up
.

I've had better results for wireless network devices if I bypass the network setup during installation and set it up the old way. For you all you really need to do is to make the /etc/hostname.run0 file according to the directions in 'man run'.

I think the run0 devices are also fairly new. I can vouch for most ral0, ath0 and rum0 devices. Prism 2.5/3.0 usb devices are buggy. Do you have an alternative wireless device?
Reply With Quote
Reply

« Previous Thread | Next Thread »
Thread Tools
Display Modes
Linear Mode Linear Mode

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
System freeze when connecting USB flash drive (4.4 & 4.5 but worked in 4.3) GardenGnome OpenBSD Installation and Upgrading 11 7th May 2009 02:32 PM
checking upgrade worked? carpman FreeBSD Installation and Upgrading 2 6th February 2009 11:37 PM
DesktopBSD & usb wifi radtek FreeBSD General 1 10th September 2008 09:13 PM
Two FW + WiFi AP Inquiry revzalot OpenBSD Security 4 14th July 2008 11:24 PM
Any wifi enthusiasts here? PatrickBaer General software and network 14 1st July 2008 01:45 PM


All times are GMT. The time now is 07:38 PM.

DaemonForums.org RSS Feeds - Contact Us - DaemonForums.org - Archive - Privacy Statement - Top

Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
Content copyright © 2007-2010, the authors
Daemon image copyright ©1988, Marshall Kirk McKusick