EFI boot problem

peterbsd · #1 **(View Single Post)** 4 Weeks Ago

Hello,
I am trying to boot fresh NetBSD 10.1 on older HP machine HP Compaq Elite 8300. System disk is GPT and contains Window and above NetBSD installation. I am using rEFInd for dual-boot.

Problem is that after selecting NetBSD boot entry there does not appear text-mode icon with:
...NetBSD/x86 EFI Boot (x64)...
So (IMHO) bootx64.efi has some problem.
There only appears some address ranges quickly scrolling up and then it stops.

But
when I boot from USB key and use manual boot parameters to boot OS from disk:
boot NAME=NetBSD:netbsd then OS on the disk successfully starts up.

I tried to rewrite bootx64.efi on EFI partition with /usr/mdec/bootx64.efi
or with bootx64.efi present on USB key, it does not help.
I don't know to explain myself this behavior.
My NetBSD installation is on wd0 dk4.
Any ideas ?

Code:

[     1.000000] Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003,
[     1.000000]     2004, 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013,
[     1.000000]     2014, 2015, 2016, 2017, 2018, 2019, 2020, 2021, 2022, 2023,
[     1.000000]     2024
[     1.000000]     The NetBSD Foundation, Inc.  All rights reserved.
[     1.000000] Copyright (c) 1982, 1986, 1989, 1991, 1993
[     1.000000]     The Regents of the University of California.  All rights reserved.

[     1.000000] NetBSD 10.1 (GENERIC) #0: Mon Dec 16 13:08:11 UTC 2024
[     1.000000] 	mkrepro%mkrepro.NetBSD.org@localhost:/usr/src/sys/arch/amd64/compile/GENERIC
[     1.000000] total memory = 24450 MB
[     1.000000] avail memory = 23624 MB
[     1.000000] timecounter: Timecounters tick every 10.000 msec
[     1.000000] Kernelized RAIDframe activated
[     1.000000] RTC BIOS diagnostic error 0x20<config_unit>
[     1.000000] timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
[     1.000004] efi: systbl at pa c943df18
[     1.000004] mainbus0 (root)
[     1.000004] ACPI: RSDP 0x00000000C9BA3000 000024 (v02 HPQOEM)
[     1.000004] ACPI: XSDT 0x00000000C9BA3080 000084 (v01 HPQOEM SLIC-BPC 01072009 AMI  00010013)
[     1.000004] ACPI: FACP 0x00000000C9BACFE8 0000F4 (v04 HPQOEM SLIC-BPC 01072009 AMI  00010013)
[     1.000004] ACPI: DSDT 0x00000000C9BA3198 009E4A (v02 HPQOEM SLIC-BPC 00000017 INTL 20051117)
[     1.000004] ACPI: FACS 0x00000000C9BB5F80 000040
[     1.000004] ACPI: APIC 0x00000000C9BAD0E0 0000BC (v03 HPQOEM SLIC-BPC 01072009 AMI  00010013)
[     1.000004] ACPI: MCFG 0x00000000C9BAD1A0 00003C (v01 HPQOEM SLIC-BPC 01072009 MSFT 00000097)
[     1.000004] ACPI: HPET 0x00000000C9BAD1E0 000038 (v01 HPQOEM SLIC-BPC 01072009 AMI. 00000005)
[     1.000004] ACPI: SSDT 0x00000000C9BAD218 000460 (v01 IdeRef IdeTable 00001000 INTL 20091112)
[     1.000004] ACPI: SSDT 0x00000000C9BAD678 00544C (v01 COMPAQ WMI      00000001 MSFT 03000001)
[     1.000004] ACPI: SLIC 0x00000000C9BB2AC8 000176 (v01 HPQOEM SLIC-BPC 00000001      00000000)
[     1.000004] ACPI: SSDT 0x00000000C9BB2C40 0009AA (v01 PmRef  Cpu0Ist  00003000 INTL 20051117)
[     1.000004] ACPI: SSDT 0x00000000C9BB35F0 000A92 (v01 PmRef  CpuPm    00003000 INTL 20051117)
[     1.000004] ACPI: DMAR 0x00000000C9BB4088 0000B8 (v01 INTEL  SNB      00000001 INTL 00000001)
[     1.000004] ACPI: ASF! 0x00000000C9BB4140 0000A5 (v32 INTEL   HCG     00000001 TFSM 000F4240)
[     1.000004] ACPI: BGRT 0x00000000C9BB41E8 00003C (v00 HPQOEM SLIC-BPC 01072009 AMI  00010013)
[     1.000004] ACPI: 5 ACPI AML tables successfully acquired and loaded
[     1.000004] ioapic0 at mainbus0 apid 2: pa 0xfec00000, version 0x20, 24 pins
[     1.000004] cpu0 at mainbus0 apid 0
[     1.000004] cpu0: Use lfence to serialize rdtsc
[     1.000004] cpu0: Intel(R) Core(TM) i7-3770 CPU @ 3.40GHz, id 0x306a9
[     1.000004] cpu0: node 0, package 0, core 0, smt 0
[     1.000004] cpu1 at mainbus0 apid 2
[     1.000004] cpu1: Intel(R) Core(TM) i7-3770 CPU @ 3.40GHz, id 0x306a9
[     1.000004] cpu1: node 0, package 0, core 1, smt 0
[     1.000004] cpu2 at mainbus0 apid 4
[     1.000004] cpu2: Intel(R) Core(TM) i7-3770 CPU @ 3.40GHz, id 0x306a9
[     1.000004] cpu2: node 0, package 0, core 2, smt 0
[     1.000004] cpu3 at mainbus0 apid 6
[     1.000004] cpu3: Intel(R) Core(TM) i7-3770 CPU @ 3.40GHz, id 0x306a9
[     1.000004] cpu3: node 0, package 0, core 3, smt 0
[     1.000004] cpu4 at mainbus0 apid 1
[     1.000004] cpu4: Intel(R) Core(TM) i7-3770 CPU @ 3.40GHz, id 0x306a9
[     1.000004] cpu4: node 0, package 0, core 0, smt 1
[     1.000004] cpu5 at mainbus0 apid 3
[     1.000004] cpu5: Intel(R) Core(TM) i7-3770 CPU @ 3.40GHz, id 0x306a9
[     1.000004] cpu5: node 0, package 0, core 1, smt 1
[     1.000004] cpu6 at mainbus0 apid 5
[     1.000004] cpu6: Intel(R) Core(TM) i7-3770 CPU @ 3.40GHz, id 0x306a9
[     1.000004] cpu6: node 0, package 0, core 2, smt 1
[     1.000004] cpu7 at mainbus0 apid 7
[     1.000004] cpu7: Intel(R) Core(TM) i7-3770 CPU @ 3.40GHz, id 0x306a9
[     1.000004] cpu7: node 0, package 0, core 3, smt 1
[     1.000004] acpi0 at mainbus0: Intel ACPICA 20221020
[     1.000004] acpi0: X/RSDT: OemId <HPQOEM,SLIC-BPC,01072009>, AslId <AMI ,00010013>
[     1.000004] acpi0: MCFG: segment 0, bus 0-63, address 0x00000000f8000000
[     1.000004] ACPI: Dynamic OEM Table Load:
[     1.000004] ACPI: SSDT 0xFFFFE6B95FCBA008 00083B (v01 PmRef  Cpu0Cst  00003001 INTL 20051117)
[     1.000004] ACPI: Dynamic OEM Table Load:
[     1.000004] ACPI: SSDT 0xFFFFE6BE573F6408 000303 (v01 PmRef  ApIst    00003000 INTL 20051117)
[     1.000004] ACPI: Dynamic OEM Table Load:
[     1.000004] ACPI: SSDT 0xFFFFE6B95FC50408 000119 (v01 PmRef  ApCst    00003000 INTL 20051117)
[     1.000004] acpi0: SCI interrupting at int 9
[     1.000004] acpi0: fixed power button present
[     1.000004] timecounter: Timecounter "ACPI-Safe" frequency 3579545 Hz quality 900
[     1.010635] hpet0 at acpi0: high precision event timer (mem 0xfed00000-0xfed00400)
[     1.010635] timecounter: Timecounter "hpet0" frequency 14318180 Hz quality 2000
[     1.011366] acpiec0 at acpi0 (H_EC, PNP0C09-1): not present
[     1.011366] TPMX (PNP0C01) at acpi0 not configured
[     1.011366] FWHD (INT0800) at acpi0 not configured
[     1.011366] attimer1 at acpi0 (TIMR, PNP0100): io 0x40-0x43,0x50-0x53 irq 0
[     1.011366] pckbc1 at acpi0 (PS2K, PNP0303) (kbd port): io 0x60,0x64 irq 1
[     1.011366] pckbc2 at acpi0 (PS2M, PNP0F03) (aux port): irq 12
[     1.011366] com0 at acpi0 (UAR1, PNP0501-1): io 0x3f8-0x3ff irq 4
[     1.011366] com0: ns16550a, 16-byte FIFO
[     1.011366] acpivga0 at acpi0 (VGA): ACPI Display Adapter
[     1.011366] acpiout0 at acpivga0 (LCD, 0x0110): ACPI Display Output Device
[     1.011366] acpiout0: brightness levels: [0-19]
[     1.011366] acpivga0: connected output devices:
[     1.011366] acpivga0:   0x0110 (acpiout0): LCD Panel, head 0
[     1.011366] acpivga1 at acpi0 (GFX0): ACPI Display Adapter
[     1.011366] acpiout1 at acpivga1 (DD01, 0x0100): ACPI Display Output Device
[     1.011366] acpiout2 at acpivga1 (DD02, 0x0400): ACPI Display Output Device
[     1.011366] acpiout2: brightness levels: [0,5,10,15,20,25,30,35,40,45,50,55,60,65,70,75,80,85,90,95,100]
[     1.011366] acpiout3 at acpivga1 (DD03, 0x0300): ACPI Display Output Device
[     1.011366] acpiout4 at acpivga1 (DD04, 0x0301): ACPI Display Output Device
[     1.011366] acpiout5 at acpivga1 (DD05, 0x0302): ACPI Display Output Device
[     1.011366] acpiout6 at acpivga1 (DD06, 0x0303): ACPI Display Output Device
[     1.011366] acpiout7 at acpivga1 (DD07, 0x0304): ACPI Display Output Device
[     1.011366] acpiout8 at acpivga1 (DD08, 0x0305): ACPI Display Output Device
[     1.011366] acpiout9 at acpivga1 (LCD, 0x0110): ACPI Display Output Device
[     1.011366] acpiout9: brightness levels: [0-19]
[     1.011366] acpivga1: connected output devices:
[     1.011366] acpivga1:   0x0110 (acpiout9): LCD Panel, head 0
[     1.011366] acpibut0 at acpi0 (PWRB, PNP0C0C-170): ACPI Power Button
[     1.011366] MEM2 (PNP0C01) at acpi0 not configured
[     1.011366] acpiwmi0 at acpi0 (WMID, PNP0C14-0): ACPI WMI Interface
[     1.011366] wmihp0 at acpiwmi0: HP WMI mappings
[     1.011366] acpifan0 at acpi0 (FAN0, PNP0C0B-0): ACPI Fan
[     1.011366] acpifan1 at acpi0 (FAN1, PNP0C0B-1): ACPI Fan
[     1.011366] acpifan2 at acpi0 (FAN2, PNP0C0B-2): ACPI Fan
[     1.011366] acpifan3 at acpi0 (FAN3, PNP0C0B-3): ACPI Fan
[     1.011366] acpifan4 at acpi0 (FAN4, PNP0C0B-4): ACPI Fan
[     1.011366] acpitz0 at acpi0 (TZ00)
[     1.011366] acpitz0: active cooling level 0: 71.0C
[     1.011366] acpitz0: active cooling level 1: 55.0C
[     1.011366] acpitz0: active cooling level 2: 0.0C
[     1.011366] acpitz0: active cooling level 3: 0.0C
[     1.011366] acpitz0: active cooling level 4: 0.0C
[     1.011366] acpitz0: levels: critical 105.0 C
[     1.011366] acpitz1 at acpi0 (TZ01): cpu0 cpu4 cpu1 cpu5 cpu2 cpu6 cpu3 cpu7
[     1.011366] acpitz1: levels: critical 105.0 C, passive 95.0 C, passive cooling
[     1.011366] ACPI: Enabled 4 GPEs in block 00 to 3F
[     1.011366] pckbd0 at pckbc1 (kbd slot)
[     1.011366] pckbc1: using irq 1 for kbd slot
[     1.011366] wskbd0 at pckbd0: console keyboard
[     1.011366] pms0 at pckbc1 (aux slot)
[     1.011366] pms0: autoconfiguration error: Failed to get E6 signature.
[     1.011366] pms0: autoconfiguration error: Failed to initialize an ALPS device.
[     1.011366] pckbc1: using irq 12 for aux slot
[     1.011366] wsmouse0 at pms0 mux 0
[     1.011366] pci0 at mainbus0 bus 0: configuration mode 1
[     1.011366] pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
[     1.011366] pchb0 at pci0 dev 0 function 0: Intel Ivy Bridge Host Bridge (rev. 0x09)
[     1.011366] ppb0 at pci0 dev 1 function 0: Intel Ivy Bridge PCI Express Root Port (rev. 0x09)
[     1.011366] ppb0: PCI Express capability version 2 <Root Port of PCI-E Root Complex> x16 @ 8.0GT/s
[     1.011366] pci1 at ppb0 bus 1
[     1.011366] pci1: i/o space, memory space enabled, rd/line, wr/inv ok
[     1.011366] nouveau0 at pci1 dev 0 function 0: NVIDIA product 107d (rev. 0xa1)
[     1.011366] hdaudio0 at pci1 dev 0 function 1: HD Audio Controller
[     1.011366] hdaudio0: interrupting at msi0 vec 0
[     1.011366] hdaudio0: HDA ver. 1.0, OSS 2, ISS 4, BSS 0, SDO 4, 64-bit
[     1.011366] hdafg0 at hdaudio0: NVIDIA product 001c
[     1.011366] hdafg0: DP00 8ch: Digital Out [Jack]
[     1.011366] hdafg0: DP01 8ch: Digital Out [Jack]
[     1.011366] hdafg0: 8ch/0ch 48000Hz PCM16*
[     1.011366] audio0 at hdafg0: playback, capture, full duplex, independent
[     1.011366] audio0: slinear_le:16 2ch 48000Hz, blk 1920 bytes (10ms) for playback
[     1.011366] audio0: slinear_le:16 2ch 48000Hz, blk 1920 bytes (10ms) for recording
[     1.011366] spkr0 at audio0: PC Speaker (synthesized)
[     1.011366] wsbell at spkr0 not configured
[     1.011366] i915drmkms0 at pci0 dev 2 function 0: Intel Ivy Bridge Integrated Graphics Device (rev. 0x09)
[     1.011366] xhci0 at pci0 dev 20 function 0: Intel 7 Series USB xHCI (rev. 0x04)
[     1.011366] xhci0: 64-bit DMA
[     1.011366] xhci0: interrupting at msi1 vec 0
[     1.011366] xhci0: xHCI version 1.0
[     1.011366] usb0 at xhci0: USB revision 3.0
[     1.011366] usb1 at xhci0: USB revision 2.0
[     1.011366] Intel 7 Series MEI Controller (miscellaneous communications, revision 0x04) at pci0 dev 22 function 0 not configured
[     1.011366] puc0 at pci0 dev 22 function 3: Intel 7 Series KT (com)
[     1.011366] com2 at puc0 port 0 (16550-compatible): ioaddr 0xf140, interrupting at ioapic0 pin 19
[     1.011366] com2: ns16550a, 16-byte FIFO
[     1.011366] wm0 at pci0 dev 25 function 0, 64-bit DMA: PCH2 LAN (82579LM) Controller (rev. 0x04)
[     1.011366] wm0: interrupting at msi2 vec 0
[     1.011366] wm0: PCI-Express bus
[     1.011366] wm0: 2048 words FLASH, version 0.13.4
[     1.011366] wm0: RX packet buffer size: 26KB
[     1.011366] wm0: Ethernet address 10:60:4b:81:4e:f0
[     1.011366] wm0: 0x6a4080<FLASH,PCIE,ASF_FIRM,AMT,WOL,EEE>
[     1.011366] ihphy0 at wm0 phy 2: i82579 10/100/1000 media interface, rev. 3
[     1.011366] ihphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
[     1.011366] ehci0 at pci0 dev 26 function 0: Intel 7 Series USB EHCI (rev. 0x04)
[     1.011366] ehci0: 64-bit DMA
[     1.011366] ehci0: interrupting at ioapic0 pin 16
[     1.011366] ehci0: BIOS has given up ownership
[     1.011366] ehci0: EHCI version 1.0
[     1.011366] ehci0: Using DMA subregion for control data structures
[     1.011366] usb2 at ehci0: USB revision 2.0
[     1.011366] hdaudio1 at pci0 dev 27 function 0: HD Audio Controller
[     1.011366] hdaudio1: interrupting at msi3 vec 0
[     1.011366] hdaudio1: HDA ver. 1.0, OSS 4, ISS 4, BSS 0, SDO 1, 64-bit
[     1.011366] hdafg1 at hdaudio1: Realtek product 0221
[     1.011366] hdafg1: DAC00 2ch: Speaker [Built-In]
[     1.011366] hdafg1: DAC01 2ch: Speaker [Jack], HP Out [Jack]
[     1.011366] hdafg1: ADC02 2ch: Line In [Jack], Mic In [Jack]
[     1.011366] hdafg1: 2ch/2ch 44100Hz 48000Hz 96000Hz 192000Hz PCM16 PCM20 PCM24 AC3
[     1.011366] audio1 at hdafg1: playback, capture, full duplex, independent
[     1.011366] audio1: slinear_le:16 2ch 48000Hz, blk 1920 bytes (10ms) for playback
[     1.011366] audio1: slinear_le:16 2ch 48000Hz, blk 1920 bytes (10ms) for recording
[     1.011366] spkr1 at audio1: PC Speaker (synthesized)
[     1.011366] wsbell at spkr1 not configured
[     1.011366] hdafg2 at hdaudio1: Intel product 2806
[     1.011366] hdafg2: DP00 8ch: Digital Out [Jack]
[     1.011366] hdafg2: 8ch/0ch 48000Hz PCM16*
[     1.011366] audio2 at hdafg2: playback, capture, full duplex, independent
[     1.011366] audio2: slinear_le:16 2ch 48000Hz, blk 1920 bytes (10ms) for playback
[     1.011366] audio2: slinear_le:16 2ch 48000Hz, blk 1920 bytes (10ms) for recording
[     1.011366] spkr2 at audio2: PC Speaker (synthesized)
[     1.011366] wsbell at spkr2 not configured
[     1.011366] ppb1 at pci0 dev 28 function 0: Intel 7 Series PCIe (rev. 0xc4)
[     1.011366] ppb1: PCI Express capability version 2 <Root Port of PCI-E Root Complex> x4 @ 5.0GT/s
[     1.011366] ppb1: link is x1 @ 2.5GT/s
[     1.011366] pci2 at ppb1 bus 2
[     1.011366] pci2: i/o space, memory space enabled, rd/line, wr/inv ok
[     1.011366] ppb2 at pci2 dev 0 function 0: Texas Instruments product 8231 (rev. 0x03)
[     1.011366] ppb2: PCI Express capability version 1 <PCI-E to PCI/PCI-X Bridge>
[     1.011366] pci3 at ppb2 bus 3
[     1.011366] pci3: i/o space, memory space enabled, rd/line, wr/inv ok
[     1.011366] fwohci0 at pci3 dev 0 function 0: Texas Instruments product 8235 (rev. 0x01)
[     1.011366] fwohci0: interrupting at ioapic0 pin 16
[     1.011366] fwohci0: OHCI version 1.10 (ROM=1)
[     1.011366] fwohci0: No. of Isochronous channels is 4.
[     1.011366] fwohci0: EUI64 01:02:03:04:00:00:01:5a
[     1.011366] fwohci0: Phy 1394a available S400, 2 ports.
[     1.011366] fwohci0: Link S400, max_rec 2048 bytes.
[     1.011366] ieee1394if0 at fwohci0: IEEE1394 bus
[     1.011366] fwip0 at ieee1394if0: IP over IEEE1394
[     1.011366] fwohci0: Initiate bus reset
[     1.011366] fwohci0: Clear PME# now
[     1.011366] ppb3 at pci0 dev 28 function 4: Intel 7 Series PCIe (rev. 0xc4)
[     1.011366] ppb3: PCI Express capability version 2 <Root Port of PCI-E Root Complex> x1 @ 5.0GT/s
[     1.011366] ppb3: link is x1 @ 2.5GT/s
[     1.011366] pci4 at ppb3 bus 4
[     1.011366] pci4: i/o space, memory space enabled, rd/line, wr/inv ok
[     1.011366] wm1 at pci4 dev 0 function 0, 64-bit DMA: Intel i82574L (rev. 0x00)
[     1.011366] wm1: for TX and RX interrupting at msix4 vec 0 affinity to 1
[     1.011366] wm1: for TX and RX interrupting at msix4 vec 1 affinity to 2
[     1.011366] wm1: for LINK interrupting at msix4 vec 2
[     1.011366] wm1: PCI-Express bus
[     1.011366] wm1: 2048 words FLASH, version 1.8.0, Image Unique ID ffffffff
[     1.011366] wm1: ASPM L0s and L1 are disabled to workaround the errata.
[     1.011366] wm1: RX packet buffer size: 20KB
[     1.011366] wm1: Ethernet address 68:05:ca:1a:df:15
[     1.011366] wm1: 0x224080<FLASH,PCIE,ASF_FIRM,WOL>
[     1.011366] makphy0 at wm1 phy 1: Marvell 88E1149 Gigabit PHY, rev. 1
[     1.011366] makphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
[     1.011366] ehci1 at pci0 dev 29 function 0: Intel 7 Series USB EHCI (rev. 0x04)
[     1.011366] ehci1: 64-bit DMA
[     1.011366] ehci1: interrupting at ioapic0 pin 23
[     1.011366] ehci1: BIOS has given up ownership
[     1.011366] ehci1: EHCI version 1.0
[     1.011366] ehci1: Using DMA subregion for control data structures
[     1.011366] usb3 at ehci1: USB revision 2.0
[     1.011366] ppb4 at pci0 dev 30 function 0: Intel 82801BA Hub-PCI Bridge (rev. 0xa4)
[     1.011366] pci5 at ppb4 bus 5
[     1.011366] pci5: i/o space, memory space enabled
[     1.011366] fxp0 at pci5 dev 0 function 0: i82558 Ethernet (rev. 0x04)
[     1.011366] fxp0: interrupting at ioapic0 pin 20
[     1.011366] fxp0: May need receiver lock-up workaround
[     1.011366] fxp0: Ethernet address 00:a0:c9:9a:8c:21
[     1.011366] inphy0 at fxp0 phy 1: i82555 10/100 media interface, rev. 0
[     1.011366] inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
[     1.011366] ichlpcib0 at pci0 dev 31 function 0: Intel Q77 LPC (rev. 0x04)
[     1.011366] timecounter: Timecounter "ichlpcib0" frequency 3579545 Hz quality 1000
[     1.011366] ichlpcib0: 24-bit timer
[     1.011366] tco0 at ichlpcib0: TCO (watchdog) timer configured.
[     1.011366] tco0: Min/Max interval 1/367 seconds
[     1.011366] pciide0 at pci0 dev 31 function 2: Intel 7 Series (desktop) SATA Controller (rev. 0x04)
[     1.011366] pciide0: bus-master DMA support present, but unused (no driver support)
[     1.011366] pciide0: primary channel configured to native-PCI mode
[     1.011366] pciide0: using ioapic0 pin 19 for native-PCI interrupt
[     1.011366] atabus0 at pciide0 channel 0
[     1.011366] pciide0: secondary channel configured to native-PCI mode
[     1.011366] atabus1 at pciide0 channel 1
[     1.011366] ichsmb0 at pci0 dev 31 function 3: Intel 7 Series SMBus Controller (rev. 0x04)
[     1.011366] ichsmb0: interrupting at ioapic0 pin 18
[     1.011366] iic0 at ichsmb0: I2C bus
[     1.011366] pciide1 at pci0 dev 31 function 5: Intel 7 Series (desktop) SATA Controller (rev. 0x04)
[     1.011366] pciide1: bus-master DMA support present, but unused (no driver support)
[     1.011366] pciide1: primary channel wired to native-PCI mode
[     1.011366] pciide1: using ioapic0 pin 19 for native-PCI interrupt
[     1.011366] atabus2 at pciide1 channel 0
[     1.011366] pciide1: secondary channel wired to native-PCI mode
[     1.011366] atabus3 at pciide1 channel 1
[     1.011366] isa0 at ichlpcib0
[     1.011366] tpm0 at isa0 iomem 0xfed40000-0xfed40fff irq 7
[     1.011366] tpm0: device 0x000b15d1 rev 0x10
[     1.011366] pcppi0 at isa0 port 0x61
[     1.011366] spkr3 at pcppi0: PC Speaker
[     1.011366] wsbell at spkr3 not configured
[     1.011366] midi0 at pcppi0: PC speaker
[     1.011366] sysbeep0 at pcppi0
[     1.011366] attimer1: attached to pcppi0
[     1.011366] acpicpu0 at cpu0: ACPI CPU
[     1.011366] acpicpu0: C1: FFH, lat   1 us, pow  1000 mW
[     1.011366] acpicpu0: C2: FFH, lat  59 us, pow   500 mW
[     1.011366] acpicpu0: C3: FFH, lat  80 us, pow   350 mW
[     1.011366] acpicpu0: P0: FFH, lat  10 us, pow 77000 mW, 3401 MHz, turbo boost
[     1.011366] acpicpu0: P1: FFH, lat  10 us, pow 77000 mW, 3400 MHz
[     1.011366] acpicpu0: P2: FFH, lat  10 us, pow 73840 mW, 3300 MHz
[     1.011366] acpicpu0: P3: FFH, lat  10 us, pow 67694 mW, 3100 MHz
[     1.011366] acpicpu0: P4: FFH, lat  10 us, pow 64705 mW, 3000 MHz
[     1.011366] acpicpu0: P5: FFH, lat  10 us, pow 61772 mW, 2900 MHz
[     1.011366] acpicpu0: P6: FFH, lat  10 us, pow 58907 mW, 2800 MHz
[     1.011366] acpicpu0: P7: FFH, lat  10 us, pow 53315 mW, 2600 MHz
[     1.011366] acpicpu0: P8: FFH, lat  10 us, pow 50601 mW, 2500 MHz
[     1.011366] acpicpu0: P9: FFH, lat  10 us, pow 47940 mW, 2400 MHz
[     1.011366] acpicpu0: P10: FFH, lat  10 us, pow 42787 mW, 2200 MHz
[     1.011366] acpicpu0: P11: FFH, lat  10 us, pow 40284 mW, 2100 MHz
[     1.011366] acpicpu0: P12: FFH, lat  10 us, pow 37833 mW, 2000 MHz
[     1.011366] acpicpu0: P13: FFH, lat  10 us, pow 35433 mW, 1900 MHz
[     1.011366] acpicpu0: P14: FFH, lat  10 us, pow 31421 mW, 1700 MHz
[     1.011366] acpicpu0: P15: FFH, lat  10 us, pow 29164 mW, 1600 MHz
[     1.011366] coretemp0 at cpu0: thermal sensor, 1 C resolution, Tjmax=105
[     1.011366] acpicpu1 at cpu1: ACPI CPU
[     1.011366] coretemp1 at cpu1: thermal sensor, 1 C resolution, Tjmax=105
[     1.011366] acpicpu2 at cpu2: ACPI CPU
[     1.011366] coretemp2 at cpu2: thermal sensor, 1 C resolution, Tjmax=105
[     1.011366] acpicpu3 at cpu3: ACPI CPU
[     1.011366] coretemp3 at cpu3: thermal sensor, 1 C resolution, Tjmax=105
[     1.011366] acpicpu4 at cpu4: ACPI CPU
[     1.011366] acpicpu5 at cpu5: ACPI CPU
[     1.011366] acpicpu6 at cpu6: ACPI CPU
[     1.011366] acpicpu7 at cpu7: ACPI CPU
[     1.011366] fwohci0: BUS reset
[     1.011366] fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode
[     1.011366] ieee1394if0: 1 nodes, maxhop <= 0 cable IRM irm(0) (me)
[     1.011366] ieee1394if0: bus manager 0
[     1.011366] timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
[     1.011366] timecounter: Timecounter "TSC" frequency 3392297000 Hz quality 3000
[     1.226499] uhub0 at usb0: NetBSD (0x0000) xHCI root hub (0x0000), class 9/0, rev 3.00/1.00, addr 0
[     1.238427] uhub0: 4 ports with 4 removable, self powered
[     1.238427] uhub1 at usb1: NetBSD (0x0000) xHCI root hub (0x0000), class 9/0, rev 2.00/1.00, addr 0
[     1.268426] uhub1: 4 ports with 4 removable, self powered
[     1.288426] uhub2 at usb2: NetBSD (0x0000) EHCI root hub (0x0000), class 9/0, rev 2.00/1.00, addr 1
[     1.308426] uhub2: 3 ports with 3 removable, self powered
[     1.308426] uhub3 at usb3: NetBSD (0x0000) EHCI root hub (0x0000), class 9/0, rev 2.00/1.00, addr 1
[     1.328426] uhub3: 3 ports with 3 removable, self powered
[     1.328426] IPsec: Initialized Security Association Processing.
[     1.358427] tpm0: read 8 bytes, expected 10
[     1.378430] tpm0: deactivating entropy source
[     1.398426] wd0 at atabus0 drive 1
[     1.418426] wd0: <MTFDDAK128MAM-1J1>
[     1.438426] wd0: drive supports 16-sector PIO transfers, LBA48 addressing
[     1.438426] wd0: 119 GB, 248085 cyl, 16 head, 63 sec, 512 bytes/sect x 250069680 sectors
[     1.468426] wd0: GPT GUID: 0b27f7c4-74b3-401c-88cd-c0d8c16ad0c3
[     1.468426] dk0 at wd0: "Basic data partition", 1021952 blocks at 2048, type: <unknown>
[     1.488425] dk1 at wd0: "EFI system partition", 204800 blocks at 1024000, type: msdos
[     1.508425] dk2 at wd0: "Microsoft reserved partition", 32768 blocks at 1228800, type: ntfs
[     1.528425] dk3 at wd0: "10bd2c78-377a-4082-8212-c1176362ec16", 80660480 blocks at 1261568, type: ntfs
[     1.548425] autoconfiguration error: wd0: wedge named 'Basic data partition' already existed, using '10bd2c78-377a-4082-8212-c1176362ec16'
[     1.568425] dk4 at wd0: "NetBSD", 163839936 blocks at 81922112, type: ffs
[     1.588425] dk5 at wd0: "swap", 4307535 blocks at 245762112, type: swap
[     1.618425] wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
[     1.618425] wd1 at atabus1 drive 0
[     1.638425] wd1: <WDC WD10EZEX-22BN5A0>
[     1.658425] wd1: drive supports 16-sector PIO transfers, LBA48 addressing
[     1.658425] wd1: 931 GB, 1938021 cyl, 16 head, 63 sec, 512 bytes/sect x 1953525168 sectors (4096 bytes/physsect)
[     1.748425] wd1: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133)
[     1.748425] wd2 at atabus1 drive 1
[     1.768424] wd2: <WDC WD5000AACS-00G8B0>
[     1.788424] wd2: drive supports 16-sector PIO transfers, LBA48 addressing
[     1.788424] wd2: 465 GB, 969021 cyl, 16 head, 63 sec, 512 bytes/sect x 976773168 sectors
[     2.328423] wd2: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133)
[     2.388433] uhub4 at uhub3 port 1: vendor 8087 (0x8087) product 0024 (0x0024), class 9/0, rev 2.00/0.00, addr 2
[     2.408421] uhub4: single transaction translator
[     2.428421] uhub5 at uhub2 port 1: vendor 8087 (0x8087) product 0024 (0x0024), class 9/0, rev 2.00/0.00, addr 2
[     2.448421] uhub5: single transaction translator
[     2.468421] uhub5: 6 ports with 6 removable, self powered
[     2.468421] uhub4: 8 ports with 8 removable, self powered
[     3.678417] umass0 at uhub5 port 1 configuration 1 interface 0
[     3.698416] umass0: Corsair (0x1b1c) Voyager 3.0 (0x1a03), rev 2.10/1.10, addr 3
[     3.718415] umass0: using SCSI over Bulk-Only
[     3.728415] scsibus0 at umass0: 2 targets, 1 lun per target
[     3.748415] sd0 at scsibus0 target 0 lun 0: <Corsair, Voyager 3.0, 000A> disk removable
[     3.768415] sd0: fabricating a geometry
[     3.788415] sd0: 29604 MB, 29604 cyl, 64 head, 32 sec, 512 bytes/sect x 60628992 sectors
[     3.818417] sd0: fabricating a geometry
[     4.188414] sd0: GPT GUID: 867794b8-d609-49ee-9c51-33a08260ec8b
[     4.188414] dk6 at sd0: "EFI system", 262144 blocks at 2048, type: msdos
[     4.208413] dk7 at sd0: "3c386667-4e85-4442-ac6e-943931e02174", 4853760 blocks at 264192, type: ffs
[     4.228413] dk8 at sd0: "ab4a17e6-df64-4eda-9827-8e4b3e9f52b9", 20480000 blocks at 5117952, type: ntfs
[     4.248413] autoconfiguration error: sd0: wedge named 'Basic data partition' already existed, using 'ab4a17e6-df64-4eda-9827-8e4b3e9f52b9'
[    22.818332] atapibus0 at atabus2: 2 targets
[    22.838331] cd0 at atapibus0 drive 0: <hp       CDDVDW SH-216BB, R8TM6YBD604VA1, HE50> cdrom removable
[    22.868333] cd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
[    22.868333] swwdog0: software watchdog initialized
[    23.588330] WARNING: 4 errors while detecting hardware; check system log.
[    23.588330] boot device: wd0
[    23.588330] root on dk4 dumps on dk5
[    23.608328] root file system type: ffs
[    23.608328] kern.module.path=/stand/amd64/10.1/modules
[    23.608328] nouveau0: NVIDIA GF119 (0d93d0a1)
[    23.788327] nouveau0: bios: version 75.19.79.00.02
[    23.938930] nouveau0: interrupting at msi5 vec 0 (nouveau0)
[    23.938930] nouveau0: fb: 512 MiB DDR3
[    24.248325] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[    24.248325] [drm] Driver supports precise vblank timestamp query.
[    24.248325] Zone  kernel: Available graphics memory: 9007199252161660 KiB
[    24.248325] Zone   dma32: Available graphics memory: 2097152 KiB
[    24.248325] nouveau0: DRM: VRAM: 512 MiB
[    24.248325] nouveau0: DRM: GART: 1048576 MiB
[    24.248325] nouveau0: DRM: TMDS table version 2.0
[    24.248325] nouveau0: DRM: DCB version 4.0
[    24.248325] nouveau0: DRM: DCB outp 00: 020003a6 0f220010
[    24.248325] nouveau0: DRM: DCB outp 01: 02000362 00020010
[    24.248325] nouveau0: DRM: DCB outp 02: 048113b6 0f220010
[    24.248325] nouveau0: DRM: DCB outp 03: 04011372 00020010
[    24.248325] nouveau0: DRM: DCB conn 00: 00410146
[    24.248325] nouveau0: DRM: DCB conn 01: 00820246
[    24.258325] nouveau0: DRM: MM: using COPY0 for buffer copies
[    24.258325] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[    24.258325] [drm] Driver supports precise vblank timestamp query.
[    24.278324] nouveau0: [drm] Cannot find any crtc or sizes
[    24.278324] [drm] Initialized nouveau 1.3.1 20120801 for nouveau0 on minor 0
[    24.278324] i915drmkms0: interrupting at msi6 vec 0 (i915drmkms0)
[    24.308324] [drm] Initialized i915 1.6.0 20200114 for i915drmkms0 on minor 1
[    24.338324] intelfb0 at i915drmkms0
[    24.338324] [drm] DRM_I915_DEBUG enabled
[    24.338324] [drm] DRM_I915_DEBUG_GEM enabled
[    24.338324] intelfb0: framebuffer at 0xd0005000, size 1280x1024, depth 32, stride 5120
[    24.408324] {drm:netbsd:intel_set_cpu_fifo_underrun_reporting+0x29c} *ERROR* uncleared fifo underrun on pipe A
[    24.408324] {drm:netbsd:intel_cpu_fifo_underrun_irq_handler+0x64} *ERROR* CPU pipe A FIFO underrun
[    24.408324] {drm:netbsd:intel_set_pch_fifo_underrun_reporting+0x14e} *ERROR* uncleared pch fifo underrun on pch transcoder A
[    24.408324] {drm:netbsd:cpt_irq_handler+0x217} *ERROR* PCH transcoder A FIFO underrun
[    24.738322] wsdisplay0 at intelfb0 kbdmux 1: console (default, vt100 emulation), using wskbd0
[    24.818322] wsmux1: connecting to wsdisplay0
[    32.278289] wsdisplay0: screen 1 added (default, vt100 emulation)
[    32.278289] wsdisplay0: screen 2 added (default, vt100 emulation)
[    32.278289] wsdisplay0: screen 3 added (default, vt100 emulation)
[    32.278289] wsdisplay0: screen 4 added (default, vt100 emulation)

bsd-keith · #2 **(View Single Post)** 4 Weeks Ago

Please enclose your output within code tags, makes it easier for people to read to help.

My guess is that it is looking at the wrong boot partition.....or maybe this - [ 1.548425] autoconfiguration error: wd0: wedge named 'Basic data partition' already existed, using '10bd2c78-377a-4082-8212-c1176362ec16'

peterbsd · #3 **(View Single Post)** 4 Weeks Ago

Thx !
I corrected it, there was two partitions with the same label, but this correction does not help.
I think this error comes before it reaches boot partition, because there does not appear text mode logo: "NetBSD/x86 EFI Boot (x64)".
So it seems like bootx64.efi has some problem and stops before displaying logo.
Still I cannot explain myself why it is able to start OS in the disk with help of USB key even I use the same file on USB key's EFI partition and harddisk EFI partition.

now dmesg sees nicely:

Code:

...

[     1.400626] wd0: <MTFDDAK128MAM-1J1>
[     1.400626] wd0: drive supports 16-sector PIO transfers, LBA48 addressing
[     1.400626] wd0: 119 GB, 248085 cyl, 16 head, 63 sec, 512 bytes/sect x 250069680 sectors
[     1.410627] wd0: GPT GUID: 0b27f7c4-74b3-401c-88cd-c0d8c16ad0c3
[     1.420627] dk0 at wd0: "Windows Recovery", 1021952 blocks at 2048, type: <unknown>
[     1.420627] dk1 at wd0: "EFI system partition", 204800 blocks at 1024000, type: msdos
[     1.420627] dk2 at wd0: "Basic data partition", 80660480 blocks at 1261568, type: ntfs
[     1.420627] dk3 at wd0: "NetBSD", 163839936 blocks at 81922112, type: ffs
[     1.420627] dk4 at wd0: "swap", 4307535 blocks at 245762112, type: swap
[     1.420627] wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
[     1.800625] wd1 at atabus1 drive 0
...

and gpt show -a wd0:

Code:

      start       size  index  contents
          0          1         PMBR
          1          1         Pri GPT header
          2         32         Pri GPT table
         34       2014         Unused
       2048    1021952      1  GPT part - de94bba4-06d1-4d40-a16a-bfd50179d6ac
                                 Type: unknown
                                 TypeID: de94bba4-06d1-4d40-a16a-bfd50179d6ac
                                 GUID: 7c76d0bd-b826-4db7-b671-e391fe3e6659
                                 Size: 499 M
                                 Label: Windows Recovery
                                 Attributes: required
    1024000     204800      2  GPT part - EFI System
                                 Type: efi
                                 TypeID: c12a7328-f81f-11d2-ba4b-00a0c93ec93b
                                 GUID: 7124e3aa-8ac6-4520-8845-578b7dde5348
                                 Size: 100 M
                                 Label: EFI system partition
                                 Attributes: None
    1228800      32768         Unused
    1261568   80660480      3  GPT part - Windows basic data
                                 Type: windows
                                 TypeID: ebd0a0a2-b9e5-4433-87c0-68b6b72699c7
                                 GUID: 10bd2c78-377a-4082-8212-c1176362ec16
                                 Size: 39385 M
                                 Label: Basic data partition
                                 Attributes: None
   81922048         64         Unused
   81922112  163839936      4  GPT part - NetBSD FFSv1/FFSv2
                                 Type: ffs
                                 TypeID: 49f48d5a-b10e-11dc-b99b-0019d1879648
                                 GUID: b4066079-fe8a-4e11-ac7d-0ff87b9f11c7
                                 Size: 80000 M
                                 Label: NetBSD
                                 Attributes: biosboot, bootme
  245762048         64         Unused
  245762112    4307535      5  GPT part - NetBSD swap
                                 Type: swap
                                 TypeID: 49f48d32-b10e-11dc-b99b-0019d1879648
                                 GUID: d319ec43-2ce5-4f30-bb8f-c67dd91c29d6
                                 Size: 2103 M
                                 Label: swap
                                 Attributes: 
  250069647         32         Sec GPT table
  250069679          1         Sec GPT header

bsd-keith · #4 **(View Single Post)** 4 Weeks Ago

Sorry, I'm not very well versed in EFI, & I don't dual/multi boot my computers, but hopefully, someone else with multi booting experience will see your post.

(My only installs are single O/S, which worked OK for me.)

shep · #5 **(View Single Post)** 3 Weeks Ago

I put together a Forum Howto on Dual Booting Linux and NetBSD:
https://daemonforums.org/showthread.php?t=11898 that probably won't be to helpful as it was based on the Grub2 bootloader. It does detail the extraction of

Code:

boot64.efi

and setting up the partitions.

A web search with terms: rEFInd, windows, netbsd does show it can be done:
https://mail-index.netbsd.org/netbsd...msg028143.html

Maybe there is enough information in that thread. I'd also consider reaching out to the rEFInd community. The main web page at the bottom has links to a SourceForge forum and Rod Smiths contact info:https://www.rodsbooks.com/refind/

There would be an option to use a Linux based Partition manager to set up the NetBSD partitions and install as detailed in the howto. Then take the risk of installing sysutils/grub2. efibootmgr is a wip so you would likely have to manually add the Windows boot entry.

A third path would be to install a Windows version of Grub2 https://sourceforge.net/projects/grub2win/

peterbsd · #6 **(View Single Post)** 3 Weeks Ago

Thank you Shep.

I resolved problem, bootx64.efi has problem specific for HP Compaq elite 8300 BIOS/UEFI or specific to EFI partition used on that machine.

I created workaround, details in mailing-list:
https://mail-index.netbsd.org/tech-i...d1.html#000760

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Problem with second hard drive on boot	Daffy	OpenBSD General	2	19th March 2011 12:49 AM
Boot problem. Geometry problem?	gulanito	FreeBSD Installation and Upgrading	0	3rd July 2009 03:03 AM
FreeBSD boot problem	kdi	FreeBSD General	2	25th May 2008 07:09 AM
Installation cd boot problem	michaela	FreeBSD Installation and Upgrading	1	20th May 2008 07:47 PM
mount on boot problem	topche	FreeBSD General	7	11th May 2008 04:07 PM